Question about 1993 Honda Accord

Open Question

1993 honda accord air flow not being directed

The blower motor has been replace. When we push on the directional buttons the air flow only goes through the front vents and the air flow is restricted. The main concern is we cannot defrost the windshield.

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 25 Answers

SOURCE: blower motor 1991 honda accord ex

the blower motor is located behind and under the glove box. its held to the blower housing by three screws. remove the three screws and the motor will slide down and towards you. to test the motor. apply power to the yelllow/black wire and ground to the blue/red wire. the motor should run. if not you prob have a faulty power resistor. 0881be0.jpg

Posted on Mar 17, 2010

iFixapples
  • 57 Answers

SOURCE: 2004 Honda Accord Air Conditioner Not Working

Sorry for the delayed response. For future reference, the blower motor resistor in an 04' Honda Accord is located under the glove box and a little to the left if you are facing it (the glove box). You just need to pull out the plastic panel (yes, you can just pull it out by hand, no tools needed for that). It should be right on the fire wall with a plug going into it. If you reach in there and pull the plug (it has a little notch so it clips into the resistor more securely; make sure you push the clip in) it should have 4 flat prongs on it that go into the resistor. The resistor itself will have 2 phillips head screws that are holding it into the fire wall. Unscrew them and you have the resistor. If you can unscrew both screws before unplugging, it will be easier to see how it unplugs. I know this sounds complicated but once you get in there you will notice it's fairly easy to change out.

Posted on Apr 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my 1993 buick roadmaster heat fine but most times the blower won't blow on my windshield to defrost?


Are you referring to the blower NOT blowing air or it is blowing air but will not direct the flow to defrost?

Aug 22, 2015 | 1993 Buick Roadmaster

1 Answer

How to test blower motor on 1997 honda accord


Use jumper wire to run juice direct from battery.

Feb 26, 2015 | 1997 Honda Accord

2 Answers

Weak air flow from heaters. takes ages to clear wind screen


Can you hear the blower motor working? If so, your pollen filter may be totally plugged up causing an obstruction which prevents proper air flow. You may also have a weak blower motor.

Nov 20, 2010 | 2000 Honda Accord

1 Answer

Where is the blower motor located for a 1993 honda accord


1990-93 Accord (click for zoom)

127c766.jpg

Fig. 1: Remove the glove box and frame


d9da350.jpg

Fig. 2:
Air conditioned models require the removal of the control unit. Handle it carefully


7151369.jpg

Fig. 3: Remove the lower covers from the blower unit



Hope help with this (remember rated this).

Jul 09, 2010 | 1993 Honda Accord

1 Answer

Replaced the blower motor resistor, the air still blows through the defrost vents. Fuses are ok, what should I do next?


the blower motor resistor is for the speed of the blower not the direction of air flow you need to check the operation of the air flow direction control flaps

May 27, 2010 | 1999 GMC Yukon

1 Answer

NEED INFO ON HOW TO FIND AND REMOVE BLOWER MOTOR IN A 1993 HONDA ACCORD. IT WILL NOT WORK ON ANY SPEED AND NEEDS TO BE REPLACED.


990-93 Accord
See Figures 2, 3 and 4
  1. Disconnect the negative battery cable. If so equipped, disable the Supplemental Restraint System (SRS).
  2. Remove the glove box.
  3. Remove the glove box frame (lower support)
  4. If not equipped with air conditioning:
  5. If equipped with air conditioning:To install:
  6. Install the blower unit and tighten the retaining nuts.
  7. On air conditioned vehicles:
    1. Install the lower covers and the retaining band.
    2. Install the control unit bracket and carefully engage the wiring connectors to their proper location.
    3. Install the kick panel and reposition the carpet.

  8. Connect the wiring to the blower assembly. For non-air conditioned vehicles, install the air duct and tighten the screws.
  9. Install the glove box frame and install the glove box. Note that some of trim on the frame is held with 2-sided tape; replace the tape when reassembling as necessary.
  10. If applicable, enable the SRS.
  11. Connect the negative battery cable.

8d1d518.jpg
efc7885.jpg

Dec 28, 2009 | 1993 Honda Accord

1 Answer

No heat or air


Check the blower motor speed control resistor pack is ok.
(The resistor pack is usually located in the blower fan ducting in the air flow).
Check condition of electrical connection terminals on the blower motor circuit - these terminals pass considerable current and over time may fatigue overheat and loosen.
Check operation/replace any blower motor control relay,
Check the blower motor will run if +12v directly applied to the blower motor.
Check operation of the blower motor speed control switch is ok.

Oct 08, 2009 | 1993 Dodge Dakota

3 Answers

The heater blower is not working, cheak the fuse


replace the blower motor, common problem

Oct 08, 2009 | 1993 Honda Accord

1 Answer

Climate control buttons dont work


these cars have i issue of the knobs breaking in the back try switching the blower knob with it and see if it works as far as the clock they are not tied together most likely the bulb is burned out stick a small screw driver under it pull down the clock pops out you will be able to see the bulb

Oct 18, 2008 | 1999 Honda Accord

2 Answers

Heater blower does not come out vents


Check your vacuum lines under the hood and particularly the vacuum reservoir which is a canister that supplies a reserve on vacuum to bridge the times the engine is pulling hard. These often have plastic nipples with pushed-on hoses that can snap off.
The directional control of air flow is most often accomplished with vacuum 'motors' that move vanes to change direction. 

Sep 21, 2008 | 1996 GMC Savana

Not finding what you are looking for?
1993 Honda Accord Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...