Question about 2001 Ford Excursion

1 Answer

How to remove fuel filter

Checking fuel pressure

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

If it is a 7.3diesel you have to open a fuel line and use a fuel gauge in if is 5.4 or the v10 if you look arou.d the fuel rail there is a port to scew a gauge on to it

Posted on Nov 03, 2012

  • Brad Scribner Nov 03, 2012

    v10 I"ll look for the port

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i change the fuel filter on a 2004 hyundia sonata?


NOTEThe fuel filter is located underneath the car, near the fuel tank.
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:

    Negative battery cableFuel supply and pressure linesFuel filter bracket, if equippedFuel filter

To install:


0996b43f80231741.jpgenlarge_icon.gifenlarge_tooltip.gif

Fig. Remove the fuel filter

  1. Install or connect the following:

    Fuel filter and torque the mounting bolts to 18-25 ft. lbs. (25-35 Nm)Fuel filter bracket, if equippedFuel supply and pressure linesNegative battery cable
  2. Start the engine, check leaks and repair if necessary.


NOTEThe fuel filter is located underneath the car, near the fuel tank.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:

    Negative battery cableFuel supply and pressure linesFuel filter bracket, if equippedFuel filter

To install:

9347kg12.jpgenlarge_icon.gifenlarge_tooltip.gif

Fig. Remove the fuel filter


  1. Install or connect the following:

    Fuel filter and torque the mounting bolts to 18-25 ft. lbs. (25-35 Nm)Fuel filter bracket, if equippedFuel supply and pressure linesNegative battery cable
  2. Start the engine, check leaks and repair if necessary.


NOTEThe fuel filter is located underneath the car, near the fuel tank.
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:

    Negative battery cableFuel supply and pressure linesFuel filter bracket, if equippedFuel filter

To install:

9347kg12.jpgenlarge_icon.gifenlarge_tooltip.gif

Fig. Remove the fuel filter


  1. Install or connect the following:

    Fuel filter and torque the mounting bolts to 18-25 ft. lbs. (25-35 Nm)Fuel filter bracket, if equippedFuel supply and pressure linesNegative battery cable
  2. Start the engine, check leaks and repair if necessary.

icn_arrow.gifBack to Topbuyithere.gif

    Sorry, there are no parts available for the selected vehicle: 2004 Hyundai Sonata 2.7L MFI DOHC 6cyl.

Nov 24, 2012 | Hyundai Motor 2004 Sonata

2 Answers

Where is the fuel filter located


The fuel filter is located under the rear seat.
Fuel Filter Replacement:

  1. Reduce the internal pressure of the fuel lines and hoses by completing the following operations:
    • After removing the rear seat cushion, disconnect the fuel pump harness.
    • Start the engine. Allow it to stop by itself, then turn the ignition switch OFF .
    • Disconnect the battery negative (-) terminal.
    • Connect the fuel pump harness connector.

  2. Remove the eye bolts while holding the fuel filter nuts securely.
  3. CAUTION: Cover the fuel filter with a shop towel to avoid residual gasoline from splashing.
  4. Remove the fuel filter mounting bolts, then remove the fuel filter from the fuel filter clamp.
  5. After replacing the fuel filter, check for fuel leaks.

emissionwiz_96.gif

May 22, 2011 | 2001 Hyundai Accent

1 Answer

How would I replace my fuel Filter


The fuel filter is an integral component of the fuel pressure regulator, which is mounted on top of the fuel pump module, located in the fuel tank. When the fuel filter/regulator assembly requires service, the fuel tank must be removed from the vehicle, however, the fuel pump module does not need to be removed.
  1. Disconnect the battery ground cable.
  2. You dont have to relieve your fuel systems pressure because your jeep has an automatic bleeder.
  3. Remove the fuel tank assembly.
  4. Clean the area around the fuel filter/regulator.



0900c152800a96ce.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 5: Remove the fuel filter/pressure regulator retaining clip from the top of the assembly


0900c152800a96cf.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 6: Replace the old fuel filter/pressure regulator mounting gasket

  1. Disengage the retaining clamp from the top of the filter/regulator assembly. Discard the retaining clamp.
  2. Using 2 small prying tools, pry the filter/regulator assembly out from the top of the fuel pump module. The filter/regulator assembly will unsnap from the fuel pump module.
  3. Remove and discard the mounting gasket below the filter/regulator.
  4. Before discarding the fuel filter/pressure regulator assembly, inspect the assembly to verify that the O-rings are intact. If the smallest of the 2 O-rings cannot be found on the bottom of the filter/regulator, it may be necessary to remove it from the fuel inlet passage in the fuel pump module.

To install:


0900c152800a96d0.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 7: Check the condition of the fuel filter/pressure regulator O-rings

  1. Clean the recessed area in the pump module where the filter/regulator assembly is to be installed.
  2. Check the replacement filter/regulator assembly to make sure that the new O-rings are already installed on the assembly.
  3. Apply a small amount of clean engine oil to the O-rings.
  4. Install a new gasket on top of the fuel pump module.
  5. Press the new fuel filter/pressure regulator assembly into the top of the fuel pump module until it snaps into position (a positive click must be heard or felt).
  6. The arrow on top of the fuel pump module should be pointed towards the front of the vehicle (12 O&rsquoclock position).
  7. Turn the filter/regulator assembly until the supply tube (fitting) is pointed to the 11 O&rsquoclock position.
  8. Install new retainer clamp (the clamp snaps over the top of the filter/regulator and locks to the flanges on the pump module).
  9. Install the fuel tank assembly.
  10. Connect the negative battery cable.

Jan 28, 2011 | 1996 Jeep Grand Cherokee

1 Answer

How to locate the gas filter on a voyager 4cl lx 2003


FUEL FILTER LOCATED ON TOP OF FUEL TANK.YOU HAVE TO LOWER TANK JUST ENOUGH TO REMOVE FUEL FILTER.FIRST RELIEF FUEL PRESSURE BEFORE REMOVING FUEL FILTER.TO RELIEF FUEL PRESSURE REMOVE FUEL FILLER CAP.REMOVE FUEL PUMP RELAY FROM THE FUSE AND RELAY BOX LOCATED LEFT SIDE OF THE ENGINE COMPARTMENT. START ENGINE LET IT RUN UNTIL IT RUN OUT OF FUEL.CRANK ENGINE OVER FEW MORE TIMES TO MAKE SURE ALL FUEL OUT OF FUEL LINE.NOW FUEL PRESSURE IS RELIEF.WHEN YOU ARE DONE CHECK FOR FUEL LEAKS BEFORE DRIVING VECHICLE.

Dec 26, 2010 | 2003 Chrysler Voyager

1 Answer

How do I change the fuel filter


Fuel Filter REPLACEMENT It is recommended that the fuel filter be replaced periodically. The filter is of one-piece construction and cannot be cleaned, so it must be replaced. Carbureted Engines Fig. 1: View of the fuel filter used on carbureted engines 85551036.gif
  1. Remove the air cleaner.
  2. Loosen and remove the fuel tube from the filter.
  3. Unscrew the filter from the carburetor.
  4. Apply Loctite® or equivalent to the external threads of the new filter and screw the filter into the carburetor.
  5. Hand-start the tube nut into the fuel filter. While holding the filter with a wrench to prevent it from turning, tighten the fuel line tube nut.
  6. Start the engine and check for fuel leaks.
  7. Replace the air cleaner.
Fuel Injected Engines Fig. 2: Exploded view of the fuel filter mounting on fuel injected engines 85551037.gif
Fig. 3: Use a hand vacuum pump to relieve the fuel system pressure 85551038.gif Fig. 4: Exploded view of the fuel inertia cut-off switch and its location 85551039.gif
Fig. 5: Exploded view of the 5⁄16 in. hairpin clip type quick-disconnect coupling 85551040.gif
Fig. 6: Connecting and disconnecting the garter spring type quick-disconnect couplings 85551041.gif
Remove the fuel filter mounting bracket retaining nuts . . . 89681p04.jpg. . . then loosen the filter retaining clamp and slide the bracket assembly back . . . 89681p05.jpg. . . to provide better access to the push connect fittings (arrows) 89681p06.jpgWith a rag positioned to catch any spilled fuel, disengage the retainer clip and remove the line 89681p07.jpg NOTE: The inline reservoir type fuel filter should last the left of the vehicle under normal driving conditions. If the filter does need to be replaced, proceed as follows: CAUTION
If the fuel filter is being serviced with the rear of the vehicle higher than the front, or if the tank is pressurized, fuel leakage or siphoning from the tank fuel lines could occur. To prevent this condition, maintain the vehicle front end at or above the level of the rear of vehicle. Also, relieve tank pressure by loosening the fuel fill cap. The cap should be tightened after pressure is relieved.
  1. Shut the engine OFF. Depressurize the fuel system as follows: On the 2.3L EFI engine, a valve is located on the throttle body for this purpose. The valve can be located by removing the air cleaner. On the 2.9L EFI engine use the following steps:
    • Remove the gas cap.
    • Disconnect the vacuum hose from the pressure regulator located on the engine fuel rail.
    • Using a hand vacuum pump, apply approximately 25 in. Hg pressure to the pressure regulator.
    Fuel pressure will be released into the fuel tank through the fuel return hose. On most EFI engines the fuel pressure can be relieved as follows. Use special tool T80L-9974-B or equivalent attached to the pressure measuring port on the engine fuel rail. Direct the drain hose to a suitable container and depress the pressure relief button. An alternate method of relieving the fuel system pressure is to disconnect the electrical connector from the inertia switch and crank the engine for about 15–30 seconds until it runs out of fuel and dies.
  2. Raise and support the vehicle safely.
  3. Remove the push connect fittings at both ends of fuel filter. Install new retainer clips in each push connect fitting.
  4. Remove the filter from the bracket by loosening the filter retaining clamp enough to allow the filter to pass through. NOTE: The flow arrow direction should be positioned as installed in the bracket to ensure proper flow of fuel through the replacement filter.
  5. Install the filter in the bracket, ensuring proper direction of flow as noted by arrow. Tighten clamp to 15–25 inch lbs. (1.7–2.8 Nm).
  6. Install the push connect fittings at both ends of the filter.
  7. Lower the vehicle.
  8. Start the engine and check for leaks. Clean all dirt and/or grease from the fuel filter fittings. "Quick Connect'' fittings are used on models equipped with a pressurized fuel system. These fittings must be disconnected using the proper procedure or the fittings may be damaged. The fuel filter uses a "hairpin'' clip retainer. Spread the two hairpin clip legs about 1⁄8 in. (3mm) each to disengage it from the fitting, then pull the clip outward. Use finger pressure only; do not use any tools. Push the quick connect fittings onto the filter ends. Ford recommends that the retaining clips be replaced whenever removed. The fuel tubes used on these fuel systems are manufactured in 5⁄16 in. and 3⁄8 in. diameters. Each fuel tube takes a different size hairpin clip, so keep this in mind when purchasing new clips. A click will be heard when the hairpin clip snaps into its proper position. Pull on the lines with moderate pressure to ensure proper connection. Start the engine and check for fuel leaks. If the inertia switch (reset switch) was disconnected to relieve the fuel system pressure, cycle the ignition switch from the OFF to ON position several times to re-charge the fuel system before attempting to start the engine. prev.gif next.gif

Aug 13, 2010 | 1987 Ford Bronco II

2 Answers

Locating fuel pressure regulator


Fuel Pressure Regulator Removal & Installation 2.2L Engine To Remove:
  1. Relieve the pressure in the fuel system.
  2. Disconnect the negative battery cable.
  3. Disconnect the vacuum hose from the fuel pressure regulator.
  4. Remove the pressure regulator mounting screw.
  5. Remove the fuel pressure regulator assembly with O-ring. Inspect filter screen for contamination. If contaminated, remove and discard.
Fuel pressure regulator removal/installation (2.2L SFI engine) gm-05-22-619.gif

To Install:
  1. Apply clean engine oil to the new pressure regulator O-ring and install the O-ring on the regulator.
  2. Install the regulator on the fuel rail. Apply thread-locker to the mounting screw.
    • Tighten the screw to 106 lb in (12Nm).
  3. Connect the negative battery cable.
  4. Use the following procedure to pressurize the fuel system and check for leaks;
  5. Turn the ignition ON for 2 seconds.
  6. Turn the ignition OFF for 10 seconds.
  7. Turn the ignition switch back ON to run the fuel pump again and pressurize the fuel system.
  8. Check the fuel rail assembly for fuel leaks.
4.3L Engine RPO L35 To Remove:
4.3L (RPO L35) Fuel meter body assembly gm_trk_sil15_02-04_43_fuel_metr_body_assy.gif

  1. Before servicing the vehicle, refer to the Cautions and Warnings in the beginning of this section
  2. Remove or disconnect the following:
    • Upper intake manifold (See: Upper Intake Manifold)
    • Fuel pressure regulator retainer clip (M) and discard the clip
    • Regulator (N) from the housing by twisting and pulling the fuel pressure regulator (N) and using a shop towel to catch any spilled fuel
    • Regulator seal O-ring (R) and discard the O-ring seal
    • Regulator filter (Q) and discard the filter
    • Regulator seal O-ring (P) and discard the O-ring seal
    • Backup ring (O) and discard the ring
  3. Cover the fuel pressure regulator housing to prevent contamination from entering the fuel system
To Install:
4.3L (RPO L35) Fuel meter body assembly gm_trk_sil15_02-04_43_fuel_metr_body_assy.gif

  1. Lubricate the NEW O-ring seals with clean engine oil
  2. Assemble the following new parts to the fuel pressure regulator:
    • Backup ring (O)
    • Regulator seal O-ring (P)
    • Regulator filter (Q)
    • Regulator seal O-ring (R)
  3. Install or connect the following:
    • Fuel pressure regulator with the vacuum tube pointing down
    • Fuel pressure regulator retainer clip (M)
    • Upper manifold
  4. Test drive the vehicle to confirm the repairs
RPO LU3 To Remove:
4.3L (RPO LU3) Fuel meter body assembly gm_trk_sil15_02-04_43_rpolu3_fuel_metr_body_assy.gif

  1. Before servicing the vehicle, refer to the Cautions and Warnings in the beginning of this section
  2. Remove or disconnect the following:
    • Upper intake manifold
    • Fuel pressure regulator retainer clip (E)
    • Regulator (F) from the housing by twisting and pulling the fuel pressure regulator (F) while using a shop towel to catch any spilled fuel
    • Regulator seal O-ring (J) and discard the O-ring seal
    • Regulator filter (I) and discard the filter
    • Regulator seal O-ring (H) and discard the seal
    • Backup ring (G) and discard the backup ring
  3. Cover the fuel pressure regulator housing to prevent contamination from entering the fuel system
To Install:
4.3L (RPO LU3) Fuel meter body assembly gm_trk_sil15_02-04_43_rpolu3_fuel_metr_body_assy.gif

  1. Lubricate the NEW O-ring seals with clean engine oil.
  2. Assemble the following new parts to the fuel pressure regulator:
    • Backup ring (G)
    • Regulator seal O-ring (H)
    • Regulator filter (I)
    • Regulator seal O-ring (J)
  3. Install or connect the following:
    • Fuel pressure regulator (F) with the vacuum tube pointing down
    • Fuel pressure regulator retainer clip (E)
    • Upper intake manifold
  4. Test drive the vehicle to confirm the repairs
prev.gif next.gif

Aug 05, 2010 | 2001 Chevrolet Blazer

2 Answers

How to change fuel fillter


2002 Hyundai Sonata 2.4L MFI DOHC 4cyl the Fuel Filter is located uUnder vehicle, driver side, below seating area, driver side of fuel tank, mounted on frame in fuel line.


Hyundai Car 1999-05 - Removal & Installation

NOTE The fuel filter is located underneath the car, near the fuel tank.
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    Negative battery cable Fuel supply and pressure lines Fuel filter bracket, if equipped Fuel filter
To install:

d8227e1.jpg

Fig. Remove the fuel filter
  1. Install or connect the following:
    Fuel filter and torque the mounting bolts to 18-25 ft. lbs. (25-35 Nm) Fuel filter bracket, if equipped Fuel supply and pressure lines Negative battery cable
  2. Start the engine, check leaks and repair if necessary.
NOTE The fuel filter is located underneath the car, near the fuel tank.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    Negative battery cable Fuel supply and pressure lines Fuel filter bracket, if equipped Fuel filter
To install:

  1. Install or connect the following:
    Fuel filter and torque the mounting bolts to 18-25 ft. lbs. (25-35 Nm) Fuel filter bracket, if equipped Fuel supply and pressure lines Negative battery cable
  2. Start the engine, check leaks and repair if necessary.
NOTE The fuel filter is located underneath the car, near the fuel tank.
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    Negative battery cable Fuel supply and pressure lines Fuel filter bracket, if equipped Fuel filter
To install:

  1. Install or connect the following:
    Fuel filter and torque the mounting bolts to 18-25 ft. lbs. (25-35 Nm) Fuel filter bracket, if equipped Fuel supply and pressure lines Negative battery cable
  2. Start the engine, check leaks and repair if necessary.

Hope this help to solve your problem.

Apr 24, 2010 | Hyundai Motor 2002 Sonata

3 Answers

Where Is The Fuel Filter Located On A 2003 Ford Explorer V8 And How Do You Change It?


  1. Disconnect the battery ground cable.
  2. Properly relieve the fuel system pressure.
  3. Raise the vehicle on a hoist.
  4. Remove the bolts and the fuel filter heat shield.
  5. Remove the nuts and the fuel filter shield.
  6. Disconnect the quick release and spring lock couplings and remove the fuel filter.

To install:
  1. Remove any fuel line caps.
  2. Install the new fuel filter, connecting the quick-release and spring-lock couplings.
  3. Install the fuel filter shield.
  4. Install the fuel filter heat shield. Torque the bolts to 15 ft. lbs. (20 Nm).
  5. Reconnect the battery ground cable.
  6. Lower the vehicle.
  7. Start the vehicle, check for leaks and repair if necessary.


e38232f.jpg

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Mar 26, 2010 | 2003 Ford Explorer Sport

3 Answers

What is the correct fuel pressure at the rail for a 2004 Lincoln Aviator?


Disconnect the electrical connection to relieve the system's pressure. Start the Navigator and let the engine run until it stalls from lack of gasoline. Turn off the ignition, reconnect the pump's electrical connection and disconnect the negative battery cable.
  • Step 2 Detach the fuel pressure sensor vacuum hose. Check for fuel in the line. If there is fuel present in the line, the fuel delivery problem is likely caused by a faulty fuel pump pressure regulator. If there is no fuel in the line, reattach the vacuum hose and continue with the fuel delivery diagnostic.
  • Step 3 Twist off the fuel pressure test port cap and secure a pressure gauge to the fuel pressure valve. Reconnect the negative battery cable and start the engine. The pressure gauge needs to read 45 psi when at wide open throttle. High pressure readings indicate a malfunctioning pressure regulator. Low pressure readings indicate a clogged fuel filtermag-glass_10x10.gif or a broken fuel pump.
  • Step 4 Cut the engine. Relieve system pressure and remove the negative battery cable again so you can safely remove the fuel filter to check for clogs.
  • Step 5 Loosen the filter fittings and unhook the fuel lines from the filter. Undo and remove the bracket on the fuel filter.
  • Step 6 Inspect the filter for clogs and replace it with a new one if necessary. If there are no clogs, the fuel delivery problem is probably a faulty fuel pump.
  • Mar 07, 2010 | Lincoln Aviator Cars & Trucks

    2 Answers

    I need to replace a fuel filter for a 2003 hyundai xg350, where is it located?


    Please don't forget to rate!!!


    NOTE The fuel filter is located underneath the car, near the fuel tank.

    1. Before servicing the vehicle, refer to the Precautions section.
    2. Relieve the fuel system pressure.
    3. Remove or disconnect the following:

      Negative battery cable Fuel supply and pressure lines Fuel filter bracket, if equipped Fuel filter
    3dcb13b.jpg
    Fig. Remove the fuel filter


    1. Install or connect the following:

      Fuel filter and torque the mounting bolts to 18-25 ft. lbs. (25-35 Nm) Fuel filter bracket, if equipped Fuel supply and pressure lines Negative battery cable
    2. Start the engine, check leaks and repair if necessary.

    Oct 09, 2009 | Hyundai Motor 2003 XG350

    Not finding what you are looking for?
    2001 Ford Excursion Logo

    Related Topics:

    206 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    76649 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    fordexpert

    Level 3 Expert

    5537 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...