Question about Cars & Trucks

Open Question

Whirlpool fxvs6 oven: pizza getting burned under, in the middle of the oven

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Microwave with pizza oven connected to it, all quit at once, needs fuse but can't figure out where it goes.


It should be a ceramic fuse that has pigtails attached and is soldered to the circuit board near where the power comes in.

Aug 25, 2016 | Cars & Trucks

1 Answer

Las pizza de pizza hot son bienas


this isnt a question, please dont post random statements.

Aug 17, 2014 | Cars & Trucks

1 Answer

3800 burning oil


check your crankcase breather may need cleaned. so you get back pressure.

Dec 05, 2013 | 2000 Buick LeSabre Custom

1 Answer

Dodge caravan 2001 blowing burning power steering fluid.


I can answer some of your questions without being there in person.
The smell inside the van is from fresh air entering the venting system. Not sure why you don't get it from all vents. The fresh air intake is in front of the windshield and will pick up any smells from the engine compartment.
Loosing the serpentine belt would not necessarily cause you to loose ps fluid, but having a leak could drain the pump and damage the bearings in the pump, causing the pump pulley to drag on the belt.
The ps pump could be in the final stage of failing.
And the shaft seal in the pump could be leaking fluid onto the engine and exhaust.

Feb 23, 2013 | Dodge Grand Caravan Cars & Trucks

1 Answer

Whirlpool interior light won't shut off


That is a really good question....what category did you post it under?

May 28, 2012 | Cars & Trucks

1 Answer

Help. Can't change oven temperature on Whirlpool when oven is hot.


YOU HAVE ISSUES WITH CONTROLL PANEL , NEEDS REPLACED

Jan 02, 2012 | Cars & Trucks

1 Answer

How do i replace the bushing on the slider door


1. Remove sliding door trim panel , watershield, and access hole cover plates.
2. Unlatch pizza sliding door.

3. Remove latch actuator rod retainer from center door retainer hole.

4. Disconnect pizza rear door latch actuator rod from pizza remote control assembly by opening pizza clip.

5. Open pizza door sufficiently to gain access to pizza three bolts attaching pizza rear latch to pizza sliding door. Remove bolts.

6. Remove pizza sliding door rear latch with pizza remote control actuator rod attached to pizza latch, from pizza sliding door.-------------
First you need to get the right tools for the job and the right parts to fix the problem.There is a hinge pin in both the upper and lower hinges and four brass bushings and there is two different size bushings in each hinge and also two hinge pin retaining washers.as for the tools you need a spring compressor,jack,hammer,punch. First open the door all the way,put jack under door,I like to use a 2by4 board on top of the jack to help spread the wieght of the door out a little,next if the door has a wireing harness in the jamp loosen the rubber insulation form both the door and the body this gives a couble of inches of slack in the wireing.Next use the spring compressor to remove the spring,then use the punch and hammer to drive out the pins.it is very hard to get them to move an first but gets easyer as they start to move.I would recomend having a helper to hold the door upright as it will fall when the pin is removed from the hinge.Onece the pins are out move the door and jack away from the body to gain more axcess room the replace the bushings,two in the door side and two in the body side,then slide door and jack back and align hinge holes and install new pins. I allways grease the bushing and pins before installing.Drive the new pins all the way flush with the hinge and install the retainers.Reinstall the spring and reattach the wireing insulation. ------- Open the door so it is directly above the bench. Observe how all the fasteners, be they bolts or pins with bushings, are aligned. Generally, the bolts and pins point toward the center of the hinge from the top or bottom, The bolts and bushings are on the body-side bracket for the upper bracket and the door bracket for the lower one. This will help. Thanks please keep updated. please do rate the solution positively .thank you for using fixya

Apr 01, 2010 | Mercury Villager Cars & Trucks

2 Answers

Leaking transmission fluid from somewhere not under the motor.. more like middle of jeep


check your transmission pan gasket, and the Tranfercase (if 4x4) and rear of transmission seal where drive shaft goes in, if nothing else wash the underside of it first and d rive about 30 miles on the hyway and check it then for more accurate leak detection

Sep 15, 2009 | 2000 Jeep Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...