Question about Cars & Trucks

Open Question

How to remove oil pan 1994 chevy beretta 3.1 liter

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Psych0Thrash
  • 53 Answers

SOURCE: 2000 7.3 Liter diesel engine needing oil pan replacement

sadly I don't think there is. The oil pan is huge and sections of the frame are in the way of getting it in and out without damaging the pan severly. pulling that massive engine and replacing the pan, then putting the engine back in and reconnecting everything in 14 hours is a good estimate. sorry for the bad news

Posted on Aug 18, 2008

  • 5 Answers

SOURCE: 2000 Chevy Blazer

i am working on a s 10 of the same yaer and problem i will post my results after tomorrow when i have finished the job i bout this truck cause of the forum i own one that is a great one and this one is for experimental purpose i will let u know so far you cant lift the motor with a jack or a hoist so we r going another route in the mornin

Posted on Dec 27, 2008

ZJLimited
  • 17970 Answers

SOURCE: where do i find the turn signal flashers for a

GM Corsica/Beretta 1988-1996 Repair Guide

The turn signal flasher is mounted in a clip on the right side of the steering column support bracket. The hazard flasher is located in the component center, under the instrument panel, on the right side. Replace the flasher by unplugging the old one and plugging in the new one.

Hope helped (remember rated this help) Good luck.

Posted on Oct 30, 2009

Testimonial: "Thank you soooo much. It took me no time once you told me where it was."

  • 834 Answers

SOURCE: removal procedure of oil pan for a 1997 chevy

To remove the engine oil pan either the engine has to be lifted all the way off of the motor mounts and the oil pan should just clear the flex-plate and transmission, or the front axle dropped down out of the way, or the transmission and flex-plate will have to be removed.

Usually if the engine can be lifted enough to fit a piece of 2x4 wood between the motor mounts and the frame then the oil pan will usually just have enough clearance to be removed from the rear and the oil pan should just clear the transmission and the flex-plate. Also, be sure to check that the fan blade does not damage the fan shroud when lifting the engine.

Let me know if you require any further assistance.

Posted on Jul 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the drain plug located on a 1995 chevy beretta 3.1 liter?


Radiator is on the drivers side in front of the radiator(White). Oil pan is on the back side of the pan in the middle. Not one for the transmission.

Nov 29, 2015 | Cars & Trucks

1 Answer

How do I replace a oil pan on a 1993 chevy c1500 2 wheel with a 5.7 liter engine?


Drain the oil. Loosen the engine mounts and jack up the engine. Put 2x4s under the mounts. Remove all the pan bolts and drop the oil pan. You will also need to disconnect the oil cooler lines at the oil filter housing to get to some of the pan bolts. There are also some engine support brackets you will need to remove.

Oct 21, 2014 | Cars & Trucks

1 Answer

How can I change my 3.0 Liter oil pan gasket


Hi, Im AL the owner of Big As Auto Repair.

I actually own a 1995 Dodge Spirit 3.0 and its not to difficult. The hardest part is removing the bracket on the transmission so you can remove the dust cover for the flywheel. (1) Drain the oil. (2) Remove the transmission bracket and the dust cover. (3) Remover all the pan bolts except one, just loosen this one so you can pry the pan off, because the pan will be stuck on. (4) Clean the engine block and the oil pan very clean. (5) Install the gasket OR sealer which ever it calls for and install the pan and fill with new oil and filter. Hope this helps and please visit my Auto-Repair-Website: http://www.bigasautorepair.com/

Apr 25, 2014 | 1994 Dodge Spirit

1 Answer

How to remove exhauste heat sheild on 1994 chevy beretta


there should be a couple of little screws on the body of your car.

Sep 18, 2012 | 1994 Chevrolet Beretta

1 Answer

Wher is the oil pump mounted on a 1989 Chevy Cavalier Z24 2.8 Liter motor


OIL PUMP IN THE OIL PAN.YOU HAVE TO REMOVE OIL PAN TO GET TO OIL PUMP.

Nov 18, 2010 | Chevrolet Cavalier Cars & Trucks

1 Answer

Oil pan leak on 1994 bronco with a 5.0 liter


Oil Pan Removal
  1. Remove the bolts attaching the fan shroud (8146) to the radiator (8005) and position the fan shroud over the fan assembly.
  2. Raise vehicle.
  3. Remove exhaust manifold-to-exhaust pipe.
  4. Disconnect the oil cooler line at the left side of the radiator if equipped with an automatic transmission (7003).
  5. Remove the nuts and lockwashers attaching the engine support insulators to the chassis bracket.
  6. Drain the crankcase.
  7. Loosen transmission mounting nuts.
  8. Raise the engine (6007) and place wood blocks securely under the engine supports.
  9. Remove the oil pan attaching bolts and lower the oil pan (6675) onto the crossmember.
  10. Remove the oil pan from the vehicle.

Apr 07, 2010 | 1994 Ford Bronco

2 Answers

Im replacing the distributor and ignition wires on my 1994 chevy beretta 2.2 liter engine, i need info on firing order?


If you want to do it for your self, I strongly recommended to buy the manual book of your car, and it cost you $20.00 bucks only and you will learn more a lot about your car and it help you a lot. ok

Feb 13, 2010 | 1994 Chevrolet Beretta

1 Answer

Where is the oil sending unit on a 2002 Chevy Suburban V 8 engine?


Your oil pump is located under your oil pan. You need to remove the pan in order to access it. There is one bolt holding it in place, remove that bolt and then remove the oil pump. This is if you have a 4.3 liter motor.

If you have a 4.8, 5.3 or 6.0 liter motor it is considerably more difficult. If you need step by step instructions let me know, but to answer your question it is located behind the front cover of the engine. You need to remove the front cover exposing the timing chain and the oil pan in order to remove the pump on these motors. Let me know if you need further help.

Nov 04, 2009 | Chevrolet Chevy Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...