Question about Cars & Trucks

1 Answer

Saturn wont stay fireing i change plugs wires crank sensor

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 2,101 Answers

Try the ignition control module

Posted on Nov 03, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 96 jeep grand cherokee 4.0

change the computer .... PCM get a used one it fixed mine had same problem

Posted on Feb 19, 2009

  • 398 Answers

SOURCE: 1996 S-10 cranks but no fire

did you check to see if fuel pump is pumping. fuel filter isnt clogged is it? but you're sure there is no spark. because if there is spark it could be air flow problems.
and you changed the ignition switch so that's not it, how about the starter. is there any noise coming from the starter when you turn key? if it isn't lined up right.
there has to be spark if you did what you said take off a wire at night and try it . electricity to start goes, ign switch battery starter(is there a relay on s10s cant remember), the alternator is here also.to coil/distributor to wires to plugs to gasoline

also it could be the wires coming from the battery , check them for corrosion. if they are really corroded could be problem. and make sure your ground is good contact. ive seen corrosion inside wires causing no spark.
just a few ideas to check.

Posted on Feb 25, 2009

  • 23 Answers

SOURCE: 1984 volkswagen crank no start getting fuel and spark

You must have the plug leads in the wrong place on the distributor.
Firing order is 1-3-4-2
Remove the distributor cap. There is a tiny mark on the aluminum body where the cap sits on it. Turn the motor clockwise by hand until the rotor lines up with this mark. #1 plug lead should be in the distributor cap hole closest to the rotor in a clockwise direction.
If the motor still does not start rotate all the plug leads 180 Deg.

Posted on Aug 03, 2009

  • 1752 Answers

SOURCE: Acura 1992 Integra Hatchback wont start. It turns

Duh, check the coil.

Posted on Dec 22, 2009

alicantecoli
  • 22114 Answers

SOURCE: no fire? changed coil, distributor pick up and crank sensor, st

start by testing coil for power ,if no power then in the fuse panel you should have anything up too three fuses marked CONT and they should be about 10 amp ,check them

Posted on Mar 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Car wont stay started have changed my crankshift position sensor


How do you know it needed a crank sensor ? Does it have spark , did you pull a coil if it has coil on plug ignition or plug wire an see if it has spark ? If there is spark you do not need a crank sensor ! Try spraying carburetor cleaner in the intake an see if it fires , if it does you have a fuel delivery problem ! An when you change a crank sensor you need to have a crank relearn done with a scan tool. not a code reader !

Mar 22, 2015 | 2007 Dodge Charger Daytona R/T Sedan

1 Answer

What should i try next my truck quit on me and now we have replace the fuel pump and filter it run but rough so i changed out the plugs and now it will crank but wont stay running it is running and 40


You might want to remove the o2 sensor ahead of the catalytic converter and see if it will run. If it does you have a plugged catalytic converter or muffler. You can also try manually spraying gas into the throttle body and see if it stays running and if so you could have a bad fuel pressure regulator. You will also need to check the pickup wire in the dist to make sure you are getting fire or enough fire to the plugs. You can check for this by putting a tester in the spark plug wire and the other end on a spark plugs if you have a spark tester. Hope this helps.

Sep 20, 2014 | 2000 Chevrolet Silverado

1 Answer

1998 cavalier wont start no spark


If you have no spark try the ignition module, it controls the spark and if you don't have any and the coil is new its the only other option short of wiring or ecu!!

Nov 11, 2011 | 1998 Chevrolet Cavalier

1 Answer

1997 saturn sl1Trouble starting


check the crank shaft sensor its behind the starter they r cheap

Jul 01, 2010 | 1997 Saturn SL

1 Answer

My 2001 Saturn has the service engine soon light on. Checked it out and it is indicated that it is a cam position sensor. Problem here is from what I am told there is not a cam positioner sensor on the...


on a saturn the cam senser and crank senser is the same the ign system decides with the same senser wire rounting is spectic must be as factory placement also plugs must be same as oem a sight mis fire will cause that code

Mar 14, 2010 | 2001 Saturn S-Series

1 Answer

Wont start i put crank sensor on


If the crank sensor gets its signal from the torque convertor,the convertor has to go in the same way it came out,as the pickup for sensor is on the convertor...good luck...lee

Nov 06, 2009 | 2000 Saturn SL

1 Answer

'99 Saturn SC1 with intermittant check engine light P0341


a p0341 code mean cam reference performance, really it means you have a secondary ignition problem,,,,like a bad ignition module
a bad crank sensor
a high resistance spark plugs,do not use bosch platinum plugs in these cars
high resistance spark plug wires,,,i work at the dealer and the first thing we do is replace the spark plugs and wires if that dont work we replace the crank sensor,if thatdont work we reaplce the ignition mondule,and by then your fixed and you started with the cheapest items first,,,i would try plugs and wires and a crank sensor,,,,wires $50 plugs $14 crank sensor $37

Oct 23, 2009 | 1993 Saturn SC1

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...