Question about 2004 Chevrolet Silverado 1500 Crew Cab

Open Question

How to access silverado remote battery terminal

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can I program the car to recognixe the key fob.


1996 Roadmaster

  1. Locate the programming connector located in the LH trunk. Trim may have to be pulled back to access programming connector. ( Connector has black/white wires leading up to it and it is not connected to anything.)
  2. Jump programming connector terminals. Leave terminals jumped unitl step 6.
  3. System should now lock and unlock doors to indicate programming mode has been entered.
  4. Press any button on keyless remote once. System should now lock and unlock doors, indicating successful programming of keyless remote.
  5. Repeat step 4 for additional remote or other existing keyless remote. NOTE: A maximum of only two Keyless Remotes can be programmed.
  6. Remove programming connector jumper wire to exit programming mode.
  7. Test remote(s).

Oct 19, 2015 | 1996 Buick Roadmaster

1 Answer

Is there a BCM terminal on a 2001 Chevy Silverado?


No - access to all vehicle modules (including the BCM) is through the OBDII ALDL connector.

Sep 28, 2014 | 2001 Chevrolet Silverado

1 Answer

2004 sat ion cant access trunk to charge battery


Put a battery charger on the starter solenoid terminal
& a good ground,charge the battery then open trunk
& replace the battery

Feb 22, 2014 | 2004 Saturn ION

2 Answers

How do I change the battery in my 2005 Sebring, How do I remove the panel covering the battery compartment. Set by set instructions and or diagrams.


The battery is accessible without removing the left front wheel and tire assembly..
  1. Verify that the ignition switch and all accessories are OFF.
  2. Turn the steering wheel to the full left position.
  3. Disconnect and isolate the negative battery cable remote terminal from the remote battery post.
WARNING: NEVER GET UNDER A LIFTED VEHICLE IF NOT SUPPORTED PROPERLY ON SAFETY STANDS.


  1. Remove battery splash shield.
  2. Disconnect the heater blanket cord, if equipped.
Battery Location 112139093

Jan 01, 2011 | 2005 Chrysler Sebring Conv

1 Answer

We do not know how to jump the battery for the back door is shut


Hello, there is a place under the hood you can use to jump start this vehicle. here is the instructions.


Locate the remote positive terminal which is located under a red tethered cap on the engine compartment fuse block. Remove the cap to access the terminal.
  • Do not remove fuse block cover to jump start the vehicle.
  • Locate the remote negative (-) ground terminal, marked GND (-), which is located at the front of the engine compartment on the driver side of the vehicle.



    mrtechwrench_0.gifmrtechwrench_1.gif

    Nov 04, 2010 | 2006 Chevrolet HHR

    1 Answer

    Have replaced starter but when re-connecting battery, dash lights and key in ignition sound comes on without the key actually in the ignition also driving lights come on plus the truck will not crank when...


    If it didn't have this trouble before the starter was replaced, is there any remote possibility that the battery terminals got hooked up backwards?

    Feb 26, 2010 | 2000 Chevrolet Silverado

    2 Answers

    How do you reset the computer in a 2004 chevy silverado?


    Disconnect the battery negative cable for ten seconds but make sure you get the car radio code before you do this.

    Dec 20, 2009 | 2004 Chevrolet Silverado 1500 Crew Cab

    1 Answer

    Battery light stays on dim


    You may have a bad battery or alternator.
    The battery terminals should read 12V+-.2V when the car is off, and it should read 13V-14V+-.2V when the car is running. If it's lower, then your alternator is not charging your battery properly and if it's over, then it's overcharging and damaging your battery.

    Sep 16, 2009 | 2001 Chevrolet Silverado 1500

    1 Answer

    Do not know where the battery is located


    REMOVAL Disconnect and isolate the negative battery cable remote terminal from the remote battery post. Jack up the left front of the vehicle. Remove the left front wheel from the vehicle. Remove battery splash shield at the front of the wheel well.

    Feb 21, 2009 | 2005 Chrysler Sebring Conv

    1 Answer

    2002 chevy silverado


    clean ur battery terminals..take a wire brush and clean them..put it back together and make sure all terminals are tight...if that doesnt work..please let me know.

    Sep 02, 2008 | 2002 Chevrolet Silverado 1500

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    40 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    74945 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7697 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...