Question about Cars & Trucks
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 2005 Acura tl brake replacement
The Brembos that come on Type S/Manual models wear fast. I've changed them at 20,000 miles. They are expensive also.
Non-Type S/Manual models I have seen go 80,000 miles. The biggest factor on brake wear is how the vehicle is driven.
At 50,000 miles I would have them inspected. Depending on where you go, make sure you get an accurate measurement of both pads (inboard and outboard). 2mm is the service limit and about that time the indicators start making noise, but not always. Most indepent shops are going to sell you brake pads at 4mm. That's another 10,000 miles at least you could have driven on them.
Never replace just the brake pads, resurface or replace the rotors. The uneven surfaces of the rotor will cause your new pads to wear incorrectly and possibly cause brake noise. Most aftermarket pads will cause a squeel.
Posted on Sep 21, 2008
This starter can be changed without disassembling the top of the engine on the 2.5 with automatic transmission. You will need a 10mm, 14 mm, 17mm, and a 9mm wrench. First with any electrical repair disconnect the battery at the negative terminal. The starter is on the driver's side close to the firewall below the intake manifold. Remove the transmission dip stick so you don't ruin it, then look and study the starter itself. You will notice the starter drive housing with a top and bottom bolt. The top bolt is a 14mm and the bottom a 17mm, loosen both a half turn. Remove the top 14mm bolt first, then the bottom 17mm, this will allow you to pull the starter out of the bell housing. With some angling and no brackets holding the back of the starter you should be able to pull it out enough to disconnect the positive wire and 9mm nut from the soleniod. Disconnect the starter ignition small wire by pulling it off it's connector. Now just pull it out of the engine and fender void and you've got it, saving about a hundred and fifty dollars of labor. Take it to the parts house and match it up with a well made remanufactured or new starter. Reverse the proceedure, hook up the battery.
Posted on Mar 19, 2009
grantgga2: I don't think this is one you are going to want to try to change out.
It entails having to remove the left axle and part of the exhaust pipe to gain access to the starter. At that point, you have one bolt which goes in at the bottom from the starter side and bolts to the engine. The other bolt passes through the trans axle housing and bolts into the starter, pulling it up to the engine.
SCARED YA HUH? I'D SAY FROM A 1-10 FOR A WEEK END WARRIOR, IT WOULD BE ABOUT A 6.
Was I helpful?
Posted on May 03, 2009
Fig. Fig. 1: Remove the thermostat housing bolts
Fig. Fig. 2: Pull the water outlet neck away from the housing
Fig. Fig. 3: Note the installed position of the thermostat, then remove it
Good luck (remember rated this help).
Posted on Mar 15, 2010
Tips for a great answer:
Sep 26, 2016 | 2002 Acura TL 3.2 Type S
Nov 04, 2015 | Honda Cars & Trucks
Jul 18, 2014 | Acura TL Cars & Trucks
Jan 11, 2014 | 2002 Acura 3.2TL
Jul 27, 2010 | 2002 Acura 3.2TL
Jan 08, 2010 | 1996 Acura TL Series
Jul 05, 2009 | 2002 Acura 3.2TL
Jul 24, 2008 | 1999 Acura TL
Oct 20, 2017 | Cars & Trucks
24 people viewed this question
Usually answered in minutes!