Question about 1987 Dodge Ramcharger

Open Question

Ignition switch removal 87 dodge ramcharger

I believe the ignition switch is bad. it just spins and won't start the truck. It has a tilt steering wheel. i don't see any pins, screw or anything which to remove, so the switch will come out.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

m036_094
  • 107 Answers

SOURCE: do my 2004 dodge intrepid have a kill switch?

Your dodge has an antitheft system that shuts down the ignition and fuel system when the lock was tampered with. This is why they did not take the car your anti theft system did exactly what it was designed to do. You will need to get it to the dealer to get the system reset.

Mike

Posted on Jan 07, 2009

  • 1 Answer

SOURCE: steering wheel removal

were airbag module for passenger

Posted on May 15, 2009

dnewcombe1
  • 1564 Answers

SOURCE: HI GUYES WHO HAS THE SECRET TO REMOVE THE TILT

You've got to be very well versed in steering assemblies before attempting to do this. There are very strong springs int there and if not carefully positioned they can hurt you severely. You must first remove the wheel with a steering puller set. Make sure that the wheel is in the upper most position, first. then pull the wheel. keep track of the order in which the parts come out.Taking pix along the way often lend to ease the reassembly. Use the circlip removal tool to remove the clip holding the lock plate down.By now you'll be able to see the turn signal switch. remove the lever hold down screw and slide the turn lever out.Remove the three retaining screws for the switch and pull it straight towards you enough to lay it to the side. No need to diconnect the wires.Once you've finished with this, take the tilt pin remover from the set and while keeping a slihght pressure on the respective side, 9:00 for the left pin, 3:00 for the right. Remove the pins and then you'll be able to slide the collar up and away enough to get at the tilt lever. That's all. Reverse the order for assembly. Thanks, Dana

Posted on Aug 26, 2009

  • 593 Answers

SOURCE: Remove headlight assembly from a 2001 Dodge Ram

On the upper grill side of the headlight assy. there
should be 1 or 2 push pins that hold the seal on the
headlight assy to the front of the fender. Also check
for a guide/push pin on the inner top of the assy on
the outer fender side. That should be all there is to
hold the headlight in place. Hope this helps.

Posted on Apr 10, 2010

csmock132
  • 4669 Answers

SOURCE: I have a 1989 Dodge Ramcharger 318 Rear End

Did you turn the bearing adjusters on the ends? They are held still with little bolts.

Posted on Jul 09, 2010

Testimonial: "Guru csmock132 spent time and multiple contacts to help me with my '89 Dodge Ramcharger Rearend issues. Thanks csmock132!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car won't start. No power to coil


I have a 1987 dodge ramcharger I have no power going to the coil

Feb 18, 2013 | 1990 Dodge Ramcharger

1 Answer

My 87 ramcharger ignition module went bad it's a


The control module in the parts books is about the size of a voltage regulator with a 3 or 4 wire plug in one side and a large transistor on the other.
What are they trying to sell you ? Do you have a part number ?

Jan 28, 2013 | Cars & Trucks

2 Answers

My 1987 Dodge Ramcharger seems to have a dead short. Keeps burning out the tail lights, has burned out coil and ignition in the past several times, window units don't work now but didn't work on...


A short won't cause such things. I would bet your alternator/regulator is putting out too much voltage.. It should be no more than 14.8 volts MAX and more like 13.x . Check the voltage while the engine is running at least 2000 rpms.

May 13, 2011 | 1987 Dodge Ramcharger

1 Answer

I tried fixingMy 87 ramcharger but it ran great after I reconnected the ground wire and the ignition rod connects to the steering collom but it wirked great then it wouldn't start I believe its the...


All the alternator does is charge the battery while you drive. Check if your new battery is dead. But I suspect some wire between the ignition and the starter is off or wrong.

Sep 20, 2010 | 1987 Dodge Ramcharger

1 Answer

87 Ramcharger not charging


the distributor and coil have nothing to do with charging, the alternator, voltage regulator. amp gauge on the dash, battery and ignition switch ,,thats your charging system, and its always a problem on these older ramchargers most people who have had these trucks for a long time know this , i put 3 batterys 2 alt. 2 voltage regulators in my 87 and a starter , tell me the whole story and ill tell ya what you have to do

Mar 04, 2009 | 1987 Dodge Ramcharger

1 Answer

The steereing and ignitionswitch have locked up.


i was try on switch and steering lock but why still locked

Nov 01, 2008 | 1986 Dodge Ramcharger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

224 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...