Question about 2006 Ford Explorer

Open Question

Freestyle remove instrument cluster - 2006 Ford Explorer

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 328 Answers

SOURCE: remove insrument cluster

This isn't too hard, but does take a while. Turn the car off & disconnect the battery. Set some blocks on the wheels. Turn the ignition on, and move the shift lever all the way to the right (low gear). Then, remove the screws from all the dash trim and (carefully!!!) pull it away - there might be some snap locks also, you don't wanna break those! After that, the panel comes out just by removing some screws. You disconnect the speedometer cable and the small string going to the gear indicator (again, be careful!!)

Posted on Dec 14, 2008

  • 4 Answers

SOURCE: dont have fuse box diagram

Theirs a reset switch for the fuel pump,try looking in the trunk under the covering somewhere i have an 01 cobra and its in the trunk but yours could be some where else

Posted on May 09, 2009

  • 1 Answer

SOURCE: How do you remove the instrument cluster for a 1999 Windstar?

i have a 1999 ford windstar with 3.0 engine it keeps damaging the instrument cluster( nothing works) it all started when i changed the headlight bulbs to a brighter one , it keeps popping the fuse so i then when to a higher rated fuse, this is when it then burnt the instrument cluster(smoke came out from under the cluster

Posted on Aug 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Cluster panel lights on 2005 ford freestar goes off and comes back on no problem with engine etc why


Pull the fuse and put it back in, first. Then pull the plug on the back of the IP and put it back in. It is intermittent. These will usually fix the problem... Corrosion.

Jul 01, 2016 | 2005 Ford Freestar

2 Answers

In my ford freestyle 2005 the dash lights and everything on there as in gauges, miles , odom, turn signals, won't work, all of the lights on the outside work tho please help !


Check all fuses sometimes fuses tie things together that u would not think have anything to do with one another there should be a full fuse box lay out in the owners manual

May 17, 2015 | 2005 Ford Freestyle

1 Answer

What do the code u1900 mean on the freestyle


it is no communication with the gem module. is the instrument cluster going crazy? if so it usually means theres a problem in the cluster and needs to be replaced

Sep 14, 2014 | Cars & Trucks

1 Answer

How to remove a dash cluster 94 toyota camry


Remove the 2 screws from the center cluster lower finish panel and remove the center cluster lower finish panel.

Remove the 4 screws from the lower edge of the instrument cluster finish panel.
Using a screwdriver, carefully pry rearward on the instrument cluster finish panel to release the clips and remove the instrument cluster finish panel.

Remove the 4 screws from the instrument panel cluster carrier. Disconnect the electrical connector and remove instrument cluster.

Reverse procedure to install.

Oct 09, 2011 | 1994 Toyota Camry

1 Answer

Insturmentation panel lights fuse blows when i start car


Try to remove the instrument panel and disconnect the harness to see if doing that gets rid of the blown fuse when starting the car. If it does, then the instrument panel should be replaced with another. If the fuse still blows when starting, then there is a wire shorted to ground somewhere.
---
Instruments and Switches Instrument Cluster Removal & Installation To Remove:
  1. Remove the instrument cluster trim plate.
  2. Remove the instrument cluster mounting screws.
  3. Rotate the instrument cluster rearward and lift up on the top of the cluster in order to disengage the locating pins.
  4. Disconnect the electrical connectors from the instrument cluster.
  5. Remove the instrument cluster.
To Install:
  1. Connect the electrical connectors to the instrument cluster.
  2. Position the locating pins to the holes in the instrument panel.
  3. Install the instrument cluster by rotating the top inward.
  4. Install the mounting screws.
  5. Install the trim plate.
prev.gif next.gif

Nov 09, 2010 | 2001 Pontiac Grand Am SE

1 Answer

I have a 2005 ford freestyle the ac is fully charged the rear works great the front passenger side is ok but the drivers side is warm about 20 degrees difference between the drivers side an passenger


there is a door that directs cold or hot air behind the dashboard in order to make the passenger's side colder or hotter relative to the driver's side.
The a/c door servo may be bad, or the temperature settings for each zone are not balanced.
In-vehicle Temperature Sensor Removal & Installation
  1. For the Five Hundred and Montego;
    • Lower the steering column to the full tilt-down position.
    • Remove the instrument cluster finish panel screws.
    • Release the locking tabs on the steering column upper shroud located behind the steering wheel.
    • Remove the instrument cluster finish panel and the steering column upper shroud as an assembly.
  2. For the Freestyle;
    • Remove the lower steering column cover.
    • Remove the lower steering column shroud.
    • Disconnect the electrical connector from the in-vehicle temperature sensor.
  3. Remove the in-vehicle temperature sensor.
To Install:
  1. Reverse the removal procedure to install.
ford_500_05-06__ac_specs.gif
prev.gif

Jul 22, 2010 | 2005 Ford Freestyle

1 Answer

Need to replace instrument cluster/AC bulbs


Hello, You can obtain a 2004 Ram Factory Service Manual with all of that information available from Promanuals.net. The reason why it may be so important is because right before the removal instructions the service manual has diagnostic instructions to try. There are numerous pages on removing the instrument cluster, and cluster bezel.

(1) Disconnect and isolate the battery negative
cable. (For Airbag)

(2) Remove the cluster bezel from the instrument
panel. (Refer to 23 - BODY/INSTRUMENT PANEL/
CLUSTER BEZEL - REMOVAL).

(3) Remove the four screws that secure the instrument
cluster to the instrument panel structural support
(Fig. 5).

(4) Pull the instrument cluster rearward far
enough to access and disconnect the instrument
panel wire harness connectors for the cluster from
the connector receptacles on the back of the cluster
housing.

(5) Remove the instrument cluster from the instrument
panel.
9e8a042.jpg

Oct 01, 2009 | 2004 Dodge Ram 1500

1 Answer

How is the instrument panel removed from the dash of a 97 mercury cougar problem


1997 Thunderbird/Cougar Instrument Cluster Removal
  1. Disconnect battery ground cable (14301).
  1. Remove retaining screws and instrument panel reinforcement (017A28).
  1. Remove retaining screws and instrument panel lower shield (045G02).
  1. Make sure air bag system is properly disarmed. Remove fasteners holding steering column. Gently lower steering column.
  1. Remove screws holding the instrument panel finish panel (044D70) and gently pry off.


    Instrument Panel Finish Panel

  1. Remove four instrument cluster retaining screws. (Do not remove screws from the instrument cluster main lens (10887) and instrument cluster mask (10890)).
  1. Slide the instrument cluster (10849) to the right of the instrument panel opening and disconnect the instrument panel harness from the back of the instrument cluster.
  1. Remove the instrument cluster from the instrument panel (04320).

1997 Thunderbird/Cougar Installation
  1. Follow removal procedure in reverse order.
  1. Tighten instrument cluster retaining screws to 2-3 Nm (18-27 lb-in).

Jun 01, 2009 | 1997 Mercury Cougar XR7

1 Answer

I need to remove the cover on the gauges on a 2001


Instrument Cluster Removal and Installation Disconnect the battery ground cable. For additional information, refer to Section 414-01 . Remove the instrument panel center finish panel. Remove the screws. Disconnect the connectors and remove the instrument panel center finish panel. Remove the hood latch release handle. Remove the screws. Lower the hood latch release handle out of the way. Remove the instrument panel steering column cover. Remove the screws. Remove the instrument panel steering column cover. Remove the instrument panel steering column opening cover reinforcement. Remove the four screws. Remove the instrument panel steering column opening cover reinforcement. Position the column gearshift lever in the low position. Partially remove the instrument cluster finish panel. Remove the screws. Position instrument the cluster finish panel to gain access to electrical connectors. Remove instrument the cluster finish panel. Disconnect the connectors. Remove instrument the cluster finish panel. NOTE: Illustration shows steering column removed for clarity. Remove the instrument cluster. Remove the screws. Remove the transmission range indicator and position the cluster forward to disconnect the three electrical connectors on the back. Remove the instrument cluster.

May 15, 2009 | 2001 Ford Explorer Sport

Not finding what you are looking for?
2006 Ford Explorer Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...