Question about Cars & Trucks

Open Question

Replace rear wheel bearing on jaguar xj8 - Cars & Trucks

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75051 Answers

SOURCE: 1998 Jaguar XJ8 front wheel bearing

it does press out/in, but they can get stuck. u are using a hydraulic bearing press?

Posted on Mar 20, 2009

  • 1 Answer

SOURCE: Rear Wheel Bearing Repair; 2005 pontiac aztek

Remove the brake caliper
Remove the disc, (rotor)
Remove the 34mm nut on the axel shaft
Remove the three (3) bolts from the back side
You will need a wheel puller (three jaw will work well)
Place the puller over the hub and tighten, this will push the shaft out of the hub. Now you have to pull the hub assy. out of the mounting bracket. I found hitting each side,of the hub with a lead hammer to work well. Don't forget to disconnect the ABS senser on the back side of the hub assy.
Do not over tighten the 34mm axel nut when you install the new assy. If you use an impact whrench on it you will damage the bearing.

Posted on May 03, 2009

  • 52 Answers

SOURCE: how to replace rear wheel bearing on s type jaguar v reg

pretty basic the same and any other wheel bearing. But you need a hydraulic press, if you dont have one of those then their is just no way that you will be able to do it.

If it is newer than an 05 you need to take it to the dealership, because they need to hook up their computer and electronically disengage the rear parking brakes by putting it into service mode.

Posted on May 11, 2009

  • 119 Answers

SOURCE: Procedure for replacing rear wheel bearings 2000 Forester

i'm assuming you don't have a hubshark,this is a tool that will alllow you to remove the bearing while the knuckle is attached to the car,you may be able to rent this tool at a auto prts store .if not you need to remove the entie knuckle,first remove the trailing arm bolt,then the lateral link bolt{long and stubborn bolt},disassemble the brake shoes and parking brake cable,abs sensor if equipped the knuckle to strut bolt{no marking necessary they are not eccentric} then you need a to use or borrow a press to remove hub and bearings good luck

Posted on Jul 26, 2009

  • 101 Answers

SOURCE: how do i replace the rear wheel bearing on my peugeot 206

wheel off remove the tin cap in the centure of the hub undo the big nut put the wheel back on with just 2 bolts finger tight so you can pull the hub off.once the hub is off take the 2 wheel bolts back out.now look in side the hub were the big nut was and you will see a sir clip take that out.then use a socket and a bench vice to press the old bearing out.use the socket and bench vice to put the new bearing back in.

Posted on Aug 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does drive shaft on jaguar 1999 xj8 need greese


the rear drive shaft universal joints should have grease ******* but someone in the past may have changed one or more with sealed joints you need to look to decide jack up the car remove out of P release handbrake rotate rear wheels and check the universal joints for grease *******

Apr 01, 2017 | 1999 Jaguar XJ

1 Answer

How to remove back bumper on 2000 jaguar xj8


remove rear mudflaps if fitted, remove screws from rear of wheel arch liners. two 19mm headed bolts from underside of bumper, be warned they sieze and a lot of force will destroy the bumper mounts and the bumper beam not cheap to repair.

Oct 31, 2013 | Jaguar XJ8 Cars & Trucks

1 Answer

Looking for info to replace front brakes and wheel bearings on 2005 jag vdp. Pictures are a plus.


the brakes are pretty much just like any car,remove the fluid reservoir cap,then the tires,then disconnect the neg term on the battery,remove the calibers,then compress with a c clamp,then install,..the bearing are removed by releasing the hub assembly by removing the axle bolts and pin, i will send pictures Monday if need be...once the bearings are replaced make sure the hub isnt overtightened...and put the reservoir cap back on the brake unit...

Sep 16, 2011 | 2001 Jaguar XJ8

2 Answers

How do I get a hold of a front bearing removal tool for my XJ8


All you need to remove the abs reluctor is a 12 point 2" socket. No special jaguar tool needed.
Rick

Apr 30, 2010 | 1998 Jaguar XJ8L

1 Answer

How to fix rear axle houb bearing nose?


If you definitely have bearing noise, the hub assembly should be removed and taken to a machine shop that can replace the bearing with a new one.

Mar 14, 2010 | 2001 Jaguar XJ8

1 Answer

Since replacing rear axle output bearings on my jaguar xj8 i have devoloped a axle whine


you might be caring debrie in side the axxle you can drain the axle oil then fill again and drive for a while then drain and chage that should help

Oct 27, 2009 | 2002 Jaguar XJ-Series

1 Answer

How do i compress the caliber on rear 2006 xj8 jaguar?


you need a c-clamp and a small block of wood..place the wood n the caliber piston and twist the bar on the c-clamp make sure your master cylinder reservoir is opened up.

Oct 22, 2009 | 2006 Jaguar XJ8

1 Answer

Can't find fuel filter


The fuel filter is located above the rear axle on the driver's side. The easiest way to replace it is to break the fuel line nut loose on the side nearest the wheel and screw it all the way off (you may have a small amount of gasoline come out of the filter, so have a container handy). Then break the fuel line nut loose on the inlet side (farthest away from the wheel well) by using your wrench to turn the entire fuel filter using the nut that is part of the filter on the side nearest the wheel well. Reinstalling the filter is just the reverse of this procedure. Be sure to check that the O-rings inside the nuts are good and don't overtighten the filter or you might cut the O-rings and the filter connections will leak

Apr 13, 2009 | 2001 Jaguar XJ8

1 Answer

1998 Jaguar XJ8 front wheel bearing


it does press out/in, but they can get stuck. u are using a hydraulic bearing press?

Mar 20, 2009 | Jaguar Xj Series Cars & Trucks

2 Answers

Transmission clonks into drive ocassionally


I would check the universal joints front and rear on the drive shaft first. They are " greased for life " what usaully happens is the grease gets washed away and the needle bearings in the caps wear and become sloppy causing a clunk when the car goes into gear. If its front wheel drive I would suspect a bad cv joint.

Dec 09, 2008 | 2001 Jaguar XJ8

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

740 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...