Question about 2007 Dodge Caliber SRT4 Hatchback

Open Question

Oil pressure sensor position 2007 dodge caliber

Looking for where the oil pressure sensor is, for troubleshooting

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
lebones337
  • 152 Answers

SOURCE: Dodge caliber oil viscosity

no it will not cause any harm over the corse of 3000 miles. 5w30 is just a little thicker. 5 is the thickness when oil is cold. 20 or 30 is thickness when oil i hot, it will be ok just dont do any hotroding. only down part is that if the dealer finds out it will void the warranty.

Posted on Jan 02, 2009

Ad
  • 701 Answers

SOURCE: where is oil pressure sensor located on 2001 dodge 2500 cummins?

Hello mhak330: My name is Roger and I can give you the answer to your question. Locate the ECM on the drivers side of the engine.look for the bottom bolt holding the ECM. To the right of the bolt you should see the oil pressure sender unit. Should you need further help please just ask. Please rate the quality of your answer. This way we know you received helpful information. Thank You for using Fix Ya. Roger

Posted on Jul 07, 2009

arauzvictor1
  • 466 Answers

SOURCE: how do i replace the cam shaft position sensor? on

What type of engine saver to have and exact model of the car

Posted on Aug 10, 2009

moparhart
  • 245 Answers

SOURCE: Reset Tire Pressure Sensor on 2007 Dodge Caliber

Hello
Welcome, If you have driven over a month and it has not reset there is a problom with one of the 4 sensors, You will need to have the TPMS scaned to see witch sensor is not working,, Here is a link explainin this in detail
http://www.chryslertpms.com/

Posted on Jul 14, 2010

  • 8 Answers

SOURCE: 2007 Dodge Caliber check engine

Most times, once your car posts a trouble code you need a OBD-II code reader to pull the code and reset the check engine light. You can get one pretty cheaply from your neighborhood auto parts store. However, some parts stores have one available that they will let you borrow for a small fee or even for free. It connects to a diagnostic port just under the driver's side dash. Dealers and repair shops will typically charge you $50-75 to read the code and reset the light.

Posted on Feb 26, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What does low oil pressure on 2008 Chevy Impala 3.5 V6 LS


Do you mean what causes low oil pressure? This is a very reliable engine for the most part. If the oil light is on or gauge is reading low, have the oil pressure sensor inspected for failure. These sensors do go bad.

Jan 27, 2016 | Cars & Trucks

1 Answer

How do i tell if i have a bad oil pump or a bad oil sensor


If oil level in engine is at proper level, I wouild suspect oil pressure sending unit, does vehicle have an oil psi gauge on dash,,,if so what does it read. if oil psi reads well then it may be an oil level sensor. if you have access to a manual oil pressure gauge, you can remove the oil psi sensor and install manual gauge to get a true reading of what oil pressure is while running. if manual gauges shows low psi, then you may be looking at an oil pump.

DW Mylin

Nov 27, 2012 | 2006 GMC Envoy

1 Answer

How to troubleshoot engine oil low pressure


if the engine is not making noise then more times then others its just a bad pressure sensor

Aug 30, 2012 | 2003 Cadillac CTS

1 Answer

I cant find the oil pressure switch


What engine? 4.7 liter it's right above the oil filter. Typically oil pressure sensors/switches are close to the oil filter on most vehicles.

Aug 07, 2012 | 2002 Jeep Grand Cherokee

3 Answers

Oil light is on but full of oil


the red oil light is on? if so you may have a faulty oil pressure sending unit or you have lost oil pressure. best way to check this is by installing a mechnical gauge on engine and seeing what pressure it is reading. if it is low oil light on then the low oil level sensor is defective

Jan 14, 2011 | 2001 Chevrolet Cavalier

1 Answer

I'm looking for the oil presher switch on a 2000 Grand Am GT


Look on the engine block for a sensor with wires on it: Sending Units & Switches Oil Pressure Sensor/Switch Removal & Installation To Remove:
  1. Remove the battery negative cable from the battery.
  2. Raise and safely support the vehicle.
  3. Disconnect the electrical connector from the engine oil pressure sensor.
  4. Remove the engine oil pressure sensor.
To Install:
  1. Install or connect the following:
    • Engine oil pressure switch. Tighten the switch to 12 ft lbs (16 Nm) on the 3.4L engine, 16 ft lbs (22 Nm) on the 2.2L engine and 106 in lb (12Nm) on the 2.4L engine.
    • Electrical connector to the engine oil pressure sensor.
  2. Lower the vehicle.
  3. Install the battery negative cable to the battery.

Aug 19, 2010 | 2000 Pontiac Grand Am GT

2 Answers

Oil pressure gauge not working ,need to know location of same.


Oil Pressure Sensor Testing
  1. Check the oil level and correct as necessary. Turn the ignition switch on, but do not start the engine.
  2. Disconnect the sensor lead at the sensor. The gauge should read full scale.
  3. Ground the connector. The gauge should read at the bottom of the scale.
  4. If the gauge functions properly, replace the sensor.

4.8L, 5.3L & 6.0L Engines
  1. If necessary, remove the engine sight shield.
  2. Disconnect the oil pressure sensor electrical connector.
  3. Using J 41712 or equivalent, remove the oil pressure sensor.
95508f3.gif
Using J 41712 or equivalent, remove the oil pressure sensor.

To install:
  1. Apply sealant to the threads of the oil pressure sensor.
  2. Using J 41712 or equivalent, install the oil pressure sensor.
    • Tighten the oil pressure sensor to 26 ft. lbs. (35 Nm).
  3. Connect the oil pressure sensor electrical connector.
  4. If necessary, install the engine sight shield.

Dec 07, 2009 | 2004 Chevrolet Avalanche

1 Answer

Oil light flickers or comes on at idle in park when engine is warmed up


Your engine oil pressure is low. Things that can cause this, are: Worn engine, oil viscosity too thin, oil pump failing, clogged pickup tube screen, filter clogged, or the pesky little oil pressure sensor is going bad. You'll need to hook up a manual oil pressure gauge to where the sensor screws in, and see what you're actually getting for oil pressure, and then decide from there as to what troubleshooting action to take. Hope this helps.

Nov 26, 2009 | 2002 Dodge Stratus

2 Answers

Oil Pressure Problems, leaks


I believe what you're looking for may be called an oil pressure switch or oil pressure sensor instead of an oil sensor. If this is correct it should be easy to locate at almost any local auto parts supplier or online at places such a www.rockauto.com. Rock Auto has an easily searched catalog and the prices seem reasonable. Also there are pictures of the part.

If what was removed is an oil pressure unit and the engine is started oil will definitely be pumped out of the engine. I hope this is of some assistance.

Nov 27, 2008 | 1994 Pontiac Bonneville

Not finding what you are looking for?
2007 Dodge Caliber SRT4 Hatchback Logo

Related Topics:

1,051 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...