Question about 2004 Jeep Grand Cherokee

1 Answer

Head Bolt Torque for a 2000 Grand Cherokee Laredo 4.0L

Replacing the head gasket and can't find specs for the Head Bolt Torque for my friend's 2000 2000 Grand Cherokee Laredo 4.0L

Posted by on

  • Anonymous Mar 13, 2014

    What is the torque spec on 2000 stratus 2.5l

  • Anonymous Mar 29, 2014

    tightening head bolts on 2006 Chevrolet aveo and the sequence and torque

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 512 Answers

The torque is a 4 step process

1 torque all bolts to 22 ft/lbs
2 torque all bolts to 45 ft/lbs
3 recheck all bolts to 45 ft/lbs
4 torque bolts 1 thru 10 to 110 ft/lbs
bolt 11 to 100 ft/lbs
bolts 12 thru 14 to 110 ft/lbs
bolt #1 is the fourth bolt from the front on the passenger side....#2 is the fourth bolt on the drivers side then you continue in a clockwise order

Posted on Jan 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can anyone.tell me the Torqe specs for a 2004 or cruiser


Head and Cam Bolt Torque specs? - PT Cruiser Forum

www.ptcruiserlinks.com > ... > Tech & Performance Forum

Nov 5, 2012 - 2 posts - ‎2 authors
I am putting everything back on after replacing the head gasket. I was wondering what the Torque Specs and Sequences are for both the Head ... Torque Specs
10 posts
Jul 28, 2012
Valve cover torque specs
5 posts
Jul 4, 2011
Timing Repair Project - Bolt Torque Specs
7 posts
Jun 16, 2011
torque specs?
9 posts
Mar 20, 2006
More results from www.ptcruiserlinks.com

Dodge Stratus / Chrysler Pt Cruiser / Sebring Camshafts ...

? 5:07
https://www.youtube.com/watch?v=2wB2o27eWgo
Aug 20, 2015 - Uploaded by World Mechanics
Dodge Stratus / Chrysler Pt Cruiser / Sebring Camshafts Install and Torque Specs 2.4 Engine. ... 2004 Chrysler PT CruiserCamshaft Install

Dodge Stratus / Chrysler Sebring / Pt Cruiser 2.4 Head ...

? 6:08
https://www.youtube.com/watch?v=7rY7tDbye-8
Aug 16, 2015 - Uploaded by World Mechanics
... Stratus / Chrysler Sebring / Pt Cruiser 2.4 Head gasket Install and torque specs We took this video to ... 2004 Chrysler PtCruiser head gasket

Jan 18, 2016 | Cars & Trucks

1 Answer

Shock absorber torque specs for 2000 jeep grand cherokee laredo


specs, rear?
we just set them to 35ft./lbs
if frisky you can read the fSM for that.
or use google, ever use google,.????? amazing my 1st hit
here ill type it for you....... omg

http://www.jeepforum.com/forum/f67/rear-shock-bolt-torque-954751/#post9025080

Dec 18, 2013 | 2003 Jeep Grand Cherokee

1 Answer

What is 2004 grand prix gt 3.8 engine head torque table


Go to autozone.com create a free account put in you cars model year etc... then look at the free manual for replacing head gasket it will have a bolt tightening sequence diagram. also they usually have to be taken off in a paticular sequemnce to avoid warping the head. If aluminum heads they usually recommend new head bolt set and having the head shaved (Leveled)

Jul 13, 2010 | 2004 Pontiac Grand Prix

1 Answer

Head bolt torque specs


i'm guessing this is a V6 3400 since the headline is a 2000 Grand Am GT
44 LB FT plus 95 degrees

Apr 05, 2010 | 2000 Pontiac Grand Am GT

2 Answers

I need to know the torque settings on the head for a 94 jeep grand cherokee laredo


Assuming the motor is an inline six
1.Middle bolt is number 1.Clockwise torque to 22 f/lb
2.Same pattern to 45 f/lb
3. same pattern to 100 f/lb
Be sure to use loctite 592 to the threads and some head gasket sealer to both sides of the head gasket.
Hope this helps

Oct 18, 2009 | 1994 Jeep Grand Cherokee

2 Answers

What is the torque specs for a 1998 jeep Cherokee classic straight 6 4.0 liter? I am replacing the head gasket and need to find the lbs of torque. Thank you for any advice, pictures, etc.


Torque sequence ------------------ front | 12 8 4 1 5 9 13 | of | | engine | 11 7 3 2 6 10 14 | ------------------ Final torque must be reached in 3 equal steps Step 1: torque all bolts (except bolt 11) to 110 Ft/Lbs Step 2: torque bolt 11 to 100 Ft/Lbs Recheck final torque in sequence.

  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Disconnect the hoses at the thermostat housing.
  4. Properly relieve the fuel system pressure.
  5. Remove the cylinder head cover.
  6. Loosen the rocker arms.
  7. Remove the pushrods.

The valvetrain components must be replaced in their original positions.
  1. Remove the intake and exhaust manifold from the cylinder head.
  2. Disconnect the spark plug wires and remove the spark plugs.
  3. Disconnect the temperature sending unit wire, ignition coil and bracket assembly from the engine.
  4. Remove the accessory drive belt(s).
  5. Unbolt and set aside the power steering pump and bracket. Do not disconnect the hoses.
  6. Remove the intake and exhaust manifold assembly.
  7. If equipped with A/C, perform the following:
    1. Remove the compressor and position it aside with the lines attached.
    2. Remove the compressor bracket bolts from the cylinder head.
    3. Loosen the through bolt at the bottom of the bracket.

  8. Remove the alternator.
  9. Remove the cylinder head bolts, the cylinder head and gasket from the block.

Bolt No. 14 cannot be removed until the head is moved forward. Pull the bolt out as far as it will go and suspend in place by wrapping with tape.
  1. Discard the gasket. Thoroughly clean the head-to-block mating surface.
  2. Clean and inspect the cylinder head thoroughly. Refer to the engine reconditioning portion outlined later in this section.

To install:
  1. Coat a new head gasket with suitable sealing compound and place it on the block. Most replacement gaskets will have the word TOP stamped on them.

Apply sealing compound only to the cylinder head gasket. Do not allow sealing compound to enter the cylinder bore.

Oct 08, 2009 | 1998 Jeep Cherokee

1 Answer

Need to know cylinder head bolt torque specs


Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Feb 07, 2009 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Head bolt torque specs for 1992 Pontiac 3.1 ltr


the last time i did the same job the gasket kit had the specs inside the box. the parts store should have a book/reference manual

Dec 09, 2008 | 1992 Pontiac Grand Prix

Not finding what you are looking for?
2004 Jeep Grand Cherokee Logo

2,560 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...