Question about Cars & Trucks
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
wow i feel sorry for you because Cadillac designed this bulb to be a don't get to bulb but OK here's what you do take the bottom cover off or skid plastic panel under neath the front end theirs little plastic clips holding it on just get come dikes and don't cut them but just use it to help pull them out. after you get that off use a flash light and locate your light housing you should see two screws holding the house in i think those screws are 8mm i cant remember remove those two screws and be careful the metal from the bumper cuts you pull the light housing out and remove all the screws around the housing and open the housing up replace the bulb and make sure your contact to the bulbs clean and then reassemble the way you took apart. if you cant get it well then best bet is take it somewhere i know Cadillac charges an arm and a leg so you can go somewhere else.
Posted on Jan 25, 2009
Hi It me Mohammad Siddiq my dear. First of all it will be wise of use to take your vehicle to a dealership or any other fully equipped w/shop. They can better tell you what the fault your vehicle has. But at the same time if your friend has the same model vehicle so you can exchange some parts with that vegicle, e.g., Mass Air Flow or TPS (Throttle Position Sensor) and can check your vehicle. These parts do not need to be programmed with scan tool. Just Simply replace these parts and switch on the ignition and wait for 01 minute, then switch off for 30 seconds and then start the engine. Now road test your vehicle, if no SES light or reduced power then there was fault with the part/s replaced. So Return those parts and now you must replace these parts with new or used ones. Anything else I may be contacted on my yahoo id email@example.com. Thanks. I am an auto technician and working in a GM dealership in Saudi Arabia. I am from Pakistan.
Posted on Apr 28, 2009
If you go to the auto parts store they should have a fuel line disconnect tool that has a 5/16ths end an a 3/8ths end. The tool is shaped like an X. Before you start you need to pull the fuel pump fuse under the front of the REAR passenger side seat while the car is running and let it stall. it will release the built up pressure. This is important unless you want gas to spray every where. Then take the tool and start with the end of the filter with two lines. Place the appropriate end of the tool over the smallest inlet, push the tool in then pull the line towards the filter and then push the line away and it should disconnect. Do the same with line above. Then you can use the two appropriate size wrenches to disconnect the outlet end. reconnecting the new filter is simple just make sure your quick connect lines click in all the way and you tighten the outlet line well, I think its like 22 or 25 ft/lbs.
Posted on Dec 15, 2009
this model has what they call fly by wire.. no accelerator cable. If the computer detects a problem in the thottle system it will not allow the engine to accelerate and will show reduced power and possibly set a check engine light. The dealer usually wants to replace the throttle assembly which is very expensive and usually un nessesary.
I have had a lot of succes with just cleaning the throttle plates real good.
Posted on Jul 08, 2010
Tips for a great answer:
Aug 10, 2017 | Cadillac Cars & Trucks
Sep 10, 2016 | 2008 Cadillac Srx
Sep 30, 2015 | 2004 Cadillac SRX
Nov 05, 2014 | Cars & Trucks
Dec 07, 2012 | 2008 Cadillac Srx
Jul 10, 2011 | 2005 Cadillac SRX
Jul 09, 2009 | 2004 Cadillac SRX
Mar 26, 2009 | 2004 Cadillac SRX
350 people viewed this question
Usually answered in minutes!