Question about 2006 Dodge Ram 1500

Open Question

How to replace a fan motor resistor for a 2005 dodge ram 2500

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
farroutideas
  • 78 Answers

SOURCE: where is the iat sensor on my 2005 dodge ram 2500

Hi there:

If your truck has a 3.7L or a 4.7L engine it is on the right side of the air box just on the engine end of the flexable rubber boot that extends from the right fender. If it is a SRT it is located in the rubber boot that extends from the front of the truck on the left hand side of the boot just before it connects to the engine.

Hope this helps
Farrout!

Posted on Mar 18, 2009

Ad
  • 3 Answers

SOURCE: water pump replacement procedure 2005 2500 dodge with cummins diesel

take off old water pump. clean up area on the motor real good.do this by using a scrapper and cleaning slolvent. when thats all done put hi temp silicon on the block water pump and the put gasket on silicon. let dry for like five minutes. put in on torque bolts to specs.

Posted on Mar 22, 2009

SOURCE: 1999 Dodge Ram 1500 Fan Motor Resistor Location

I've never seen a vehicle w/o a blower resistor. You don't need to remove the blower. The resistor is about 2 inches x 3 inches and is installed in a hole in the plenum (duct) near the blower motor. It will have a wiring harness connected to it. It could be under the passenger dash or under the hood, depending on where the blower motor is.

Posted on May 06, 2009

alicantecoli
  • 22219 Answers

SOURCE: Changing front ball joints on Dodge 2500 2005

can it not be done without removing the hub ?? dont think you can get hub off without removing the track control ball joint?do you have the right tools??

Posted on May 30, 2009

  • 270 Answers

SOURCE: Location of the rear blower

The blower motor resistor gets very hot, so it is always located in a position where the blower can keep it cool. Inside the box with the blower but accessed from the outside, usually with two screws holding it in.

Posted on Jul 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a dodge ram 3500 deisel pick up. The heater fan just quit. What do I do?


Check your fuse's first, replace if burnt out, test for power to fan motor using voltmeter. Test motor continuity same way to make sure this still works. Check that nothing is obstructing the fan down inside the vent, Blow out with air-hose (be careful)

Oct 27, 2010 | 2005 Dodge Ram 2500 Truck

1 Answer

My ac is very cold but doesn`t blow very hard even on high why and what is the fix. sam


the problem is the blower fan. it is either the resistor or the fan blower itself. check for power at fan, if power check fan resistor. if these check out ok, then it is in the switch.

Jun 19, 2010 | 2005 Dodge Ram 2500 Truck

1 Answer

2005 dodge ram 2500 a/c blower dosent kick on replaced the blower variable resistor. checked the fuses still dosent kick on the morot is good i hot wired it to test but only in high what am i missing ?


I am having the same issue. I can wiggle my keys in the ignition when it is not started and get the blower to come on. I am assuming it is ignition relay.

Jun 03, 2010 | 2005 Dodge Ram 2500 Truck

1 Answer

Dodge blower fan works on high only


Easy answer...see lots of these... typically the blower motor resistor

check for resistance readings of the resistor to confirm

part is pretty cheap... less than $30

Apr 21, 2010 | 2001 Dodge Ram 2500 Truck

1 Answer

Heater blower motor only runs on the highest setting. I have replaced the blower motor itself. What could be the problem?


if you are getting only one speed from the blower motor then it would be the (blower motor resistor) causeing the problem. the blower motor resistor is located under the dash on the passenger side next to the blower motor. unplug connector and remove two screws from housing. to test the resistor connect a continuity tester to the resistor. check between the input to the output sides of the resistor for continuity. if not replace the resistor.

Apr 12, 2010 | 2005 Dodge Ram 2500 Truck

2 Answers

No current going into the fan switch or fan motor on a 2005 dodge 2500 pickup. Where are the fuses located for these two?


There is a relay located in the engine. and there is a relay for the fan in the wiring going to the fan. You are going to have to trace the wiring from the fan back to the point of where the relay is located.

Good Luck

Jul 18, 2009 | 2006 Dodge Ram 2500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...