Question about 2011 Nissan Rogue
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
1. Open glove box
2. Unhook elastic retainer on right side
3. Locate the two "stop tabs", one on the upper left and the other on the right side. Push both to the left to clear their stops and the glove box will swing down, allowing access to the filter cover.
Posted on May 06, 2009
To change the cabin air filters (there are two, that are in same location), you first have to remove the glovebox. The glovebox itself will not come off. You have to get a phillips head screwdriver to remove the 5 screws. With the glovebox closed, locate the two screws underneath and remove, one on each side. Next open the glovebox, remove the two screws at the top. The fifth screw is on the right behind the plastic molding. Pull back on the top of the lower piece of molding until the bracket pops out. The piece of plastic located just above that piece needs to be pulled out. No need to take it out all the way, just enough to get to the screw. Once removed, with the glovebox open take the fuse panel cover to the right off to allow you better grip. Pull both sides evenly until glove box pops out.
Get a flashlight and shine it on the right side behind where the glovebox was. There is a small plastic cover about 1 inch tall by 5 inches long. It is clipped in place. Push up on the plastic clip with your thumb while pulling out and down with your other finger/fingers. Behind this is one filter. Remove it best you can. Be careful, mine had dead bee's/wasps/dust/dirt/pinestraw/etc. After removing the first, you will notice a second one to the right of that. Slide that one to the left and remove the same way as the first. Look at those filters when you remove and take note the direction of AIR FLOW ^marking. Before replacing with the new ones, vacuum out inside where the filters go as best you can to remove all that crud that fell off of the old filters when removed.
Reinstallation is the reverse of how you removed. I hope this helps all my fellow Pathfinders out there.
Posted on Jun 07, 2009
Remove instrument driver lower cover.
Remove accelerator pedal assembly.
Remove filter cover and then remove in-cabin microfilter.
Posted on Aug 27, 2009
I'm going to send you exploded view of the glove box and the in cabin micro filter cover illustration. Remove the two upper screws on the glove box and carefully pry metal clips loose.
Disconnect glove box lamp electrical connector. Do not let glove box assembly hang from glove box lamp harness.
Remove three lower screws and remove damper clip from glove box door. Separate glove box housing and passenger instrument lower panel.
Remove three screws and remove in cabin micro filter cover.
Remove in cabin micro filters from front heater and cooling unit assembly.
Note When installing two new in cabin micro filters ensure that the filters are facing in the direction indicated by the direction arrow for the airflow. Direction arrow is printed on side of in cabin micro filters.
Install in cabin micro filter cover. Reinstall glove box.
Posted on Oct 10, 2009
Testimonial: "Finaly I found the air flow door with three screws and removed it. The filter will need replacement soon. It is been replaced one time at the dealer."
Tips for a great answer:
Dec 10, 2015 | Nissan Cars & Trucks
Feb 01, 2015 | 2011 Nissan Murano
Oct 06, 2014 | 2011 Nissan Rogue
Jul 02, 2012 | 2008 Nissan Rogue
Jun 17, 2012 | Nissan Rogue Cars & Trucks
Jun 07, 2012 | 2008 Nissan Rogue
Aug 22, 2011 | 2011 Nissan Rogue
Aug 26, 2009 | 2008 Nissan Rogue
260 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: