Question about 2002 Chevrolet Cavalier Coupe

Open Question

Air blend actuator location on 2002 cavalier

Only have air to floor and vents would like to change actuator

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: 1995 Chevy k1500 heater problems.

For a 95 Chevy Silverado....I replaced the Blend Door Actuator on the passenger side. Just behind the slide out cup holder. Yo ucan acces easily by removing the ash tray piece and the glove box....Or just the glove box and work like hell to get a socket in a tight place.

There are 2 actuators....one controlling the (Mode and Temp 89018681) and the other the (Air Inlet 89018367). I called the dealer and the parts were 85-125. I got it From TBA Auto (local store) for 39.00. A 20 min job at most.

Posted on May 28, 2009

  • 1 Answer

SOURCE: 2000 Chevy Silverado 1500 The heater does not

Had the same thing happen to my truck, the blen door actuator is under the console on passenger side, but the heater core is going to be clogged if you dont have any heat coming through, but a/c works..

Posted on Oct 06, 2009

michigan man
  • 3533 Answers

SOURCE: How to change spark plugs of Chevy cavalier 2002

for the most part they are in between the fuel injector the best thing for you to do is stop by your local GM dealership in the part department and they be able to print you off the pictures and diagrams you need if all fails stop by your local library and get your hands on a Haynes auto repair manual for your car Merry Christmas and Happy New Year as always wish you the best of luck Michigan Man.

Posted on Dec 21, 2009

Testimonial: "great thanks for the info. bobbotg2005"

  • 63 Answers

SOURCE: 2003 Trailblazer No air from front face vents

first check to see if you have power going to the actuators when you switch the switch to it location if no power replace controller if you have power and no movement from actuators replace actuator. if actuators move remove hvac box and check for broken blend doors.

Posted on Jan 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 ford explorer air only blows through dash vents will not switch to floor or defrost vents


This sounds like an actuator. There is usually several (three or four) on different vehicles. There will be at least one that directs the air to different locations such as defrost. You also may have a defective selector switch. I would check this before I changed the actuator or blend door. If the blend door is defective, this usually calls for totally removing the entire dash panel and usually requires several hours work. If you have to have a repair shop do this it can be very expensive.

Dec 10, 2016 | 2002 Ford Explorer

1 Answer

Replacing 2002 chevy tahoe blend door actuator


Generally,they will be located under the middle of the dash between the blower and the controls...find a service manual for exact location

Mar 08, 2014 | 2002 Chevrolet Tahoe

1 Answer

Air blend door actuator


Possible bad blend door actuator .some gm cars can be relearned to the new climate control head

Jul 28, 2013 | 2001 Oldsmobile Aurora

1 Answer

Air, either heated or cooled only comes out the dash vents, cannot redirect air to any other vents.


The most common cause of your problem is the blend door actuator. This controls air flow from defrost, vent, floot etc. In most cases, replacing the blend door actuator will fix your problem. It's commonly located above or behind the heater vents on the floor of the cabin.

Oct 01, 2011 | 2004 Dodge Ram 1500

1 Answer

2002 ford explorer....Just changed the blower motor. Everything worked fine for a few days and now the air will only come out of the defrost and floor vent areas. When I turn the vent selector switch...


Check under dash in duct system for any vacuum hoses blown off then check under the hood on the passenger side of engine compartent.If all hoses are connected then you will have to check the heater blend door actuator and the heater blend door lever for proper operation.

Aug 04, 2011 | 2002 Ford Explorer

2 Answers

Front defroster does not work


More likely the blend door cable won't do what the actuator is asking because it's in a bind. This is common with the Cavalier. Lay on the drivers side looking up with a flashlight pointed above the gas pedal and you'll see where the blend door movement should occur. You can get thru winter by moving it with your hand.

Dec 07, 2010 | 2003 Chevrolet Cavalier

1 Answer

What is a blender/ it is suposed to a part of the heater area


The "blender" would refer to the blend actuators that change the flow of air from floor to vent to defrost or combinations. Properly working blend doors will allow you to direct air to the dash vents, the floor, the defroster, the floor and defroster or the floor and dash vents. If it is not working the heater will still work but you will hae no control oer where the air flows.

Dec 19, 2009 | 1999 Jeep Grand Cherokee

1 Answer

HVAC vent selector does not function. Air flow is


THe blend door seems to be stuck. When you change settings from defrost to floor air or, vent, the blend door opens and closes directing the air to the place you want it to go to. I have had some success spraying a lubricating oil such as WD40 under the dash on the blend door. You need to get under the dash with a flashlight to locate it. It looks like a flap. Spray it with a couple of shots of the WD40. Go easy on the spraying as you may be inhaling the fumes. Keep the doors and windows open to minimize the fumes. Wait about 1/2 hour and try the A/C functions. (defrost, floor, vent air)

Mar 09, 2009 | 2002 Buick Rendezvous

2 Answers

Heating system only blows out hot air through the vents


I would look at the air blend doors first, it sound like they are not working or your control in the dash is not working send a signal to them. they work by changing the air from hot to cold or in between.

Avalanche, Sierra And Silverado
  1. Remove the floor air outlet duct extension (1) from the floor duct (2). 0900c152801c9c8a.jpgRemove the floor air outlet duct extension (1) from the floor duct (2)
  2. Disconnect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  3. Remove the blend door actuator mounting screws from the HVAC module.
  4. Remove the blend door actuator as an assembly with the actuator cam. 0900c152801c9c8c.jpgRemove the blend door actuator mounting screws from the HVAC module
To install:
  1. Install the blend door actuator as an assembly with the actuator cam.
    1. Line up the heater/defroster valve lever with the blend door actuator cam slot.
    2. Line up the A/C valve lever with the blend door actuator cam
  2. Install the blend door actuator mounting screw to the HVAC module.
    1. Tighten the blend door actuator mounting screw to 14 inch lbs. (1.6 Nm).
  3. Connect the electrical connection at the blend door actuator (10). 0900c152801c9c8b.jpgBlend door actuator and related components
  4. Install the floor air outlet duct extension (1) to the floor air duct (2).
C/K Series
  1. Disconnect the electrical connector to the mode actuator that is located on the left side of the air distribution case.
  2. Remove the screws.
  3. Remove the adjuster links from the control lever.
  4. Remove the mode actuator.
  5. Adjust the mode actuator by completing the following steps:
    1. Connect the electrical connector to the actuator.
    2. Turn the ignition switch to the RUN position. Allow the self-positioning of the actuator.
    3. Turn the ignition switch to the OFF position.
    4. Remove the actuator from the electrical connection. 0900c152801c9c8d.jpgBlend door actuator-C/K Series
To install:
  1. Install the mode actuator.
  2. Install the screws.
  3. Install the adjuster links to the control lever.
  4. Connect the electrical connector.
  5. Test the circuit operation

Nov 27, 2008 | 2001 Chevrolet Silverado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...