Question about Cars & Trucks

Open Question

2012 VW JETTA OUTER DOOR HANDLE REMOVAL - Cars & Trucks

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: 1994 vw jetta drivers door window crank inside handle removal(man

You'll see a small ring on the inside of the crank where it meets the panel. That ring holds the crank in place. To remove the handle simple push the ring up and the handle will slide right off. Depending on the position of the crank the ring might have to be pushed up down or sideways. Hope that helps.

Posted on Feb 08, 2009

  • 2 Answers

SOURCE: how do i remove the outer rear door handle on a 07 audi Q7

Ok
Remove plastic plug on the inside of door there is 10 mm hole use a hooked pick set pick put through the hole and pull the plastic cir clip towards the back of the door that will release the smaller part of the outer handle then the handle itself can be taken out.this is so simple but so deceiving the actual cir clip is hard to notice because of all the plastic **** on the inside backing plate the cir clip is just on the inside of hole look hard it is 2mm thick & 20mm high (black plastic) place point of pick in between backing plate & cir clip hook it and pull back the front door is based on the same principle but is a lot easier

Posted on Jul 16, 2009

  • 1 Answer

SOURCE: 2006 vw jetta No power on drivers door.

I have the same Problem. I Simply cut into the middle of the boot between the door and body The broken wire was right there, I pulled each end out and held the wire there with a pair needle nose pliers, stripped the end with a knife and attach a mulyi-strand jumper between both ends with electrial wire twists. Leave 2" approx. then slip the boot back over them. Use # 14 Wire. A Quick reasonable fix. If brakes again repeat again. The new Haness will have the same Problem down the road.
John

Posted on Apr 07, 2010

Testimonial: "I had the problem fixed at the dealer. It was the harness They made the harness longer & it was free.. "

  • 1 Answer

SOURCE: 2008 BMW X3, removing the left rear outer door

2004 x3 Rear passenger door handle came off/apart. What are the steps to remove the inner door panel to access the door handle and repair it?

Posted on Oct 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

VW Jetta 2012 exterior handle will not open door; however, interior handle will open the door.


Remove the inner door panel and make sure the actuator rod for the exterior handle is still engaged. If it is then the handle itself needs to be replaced.

Oct 29, 2013 | Cars & Trucks

1 Answer

2012 vw jetta rear door outside handle removal


have this done by the pros it bolts on from the inside the door

Sep 20, 2013 | 1996 Jeep Grand Cherokee

1 Answer

How do I remove left rear door handle on 2012 vw jetta


First you need to get inside the interior panel of the car and open it. Once in there you will need to pull things aside to reach the bolts that hold the outside handle in place. If you think it will be too much to do without a guide, get a copy of Haynes auto repair for the 2012 Jetta at your local auto parts store. It will step you through it.

Jan 14, 2013 | Cars & Trucks

1 Answer

How do you remove outside handle on driver's door on 2012 s60


On a S60, 2012, (drivers door) you first remove the plastic cover in under which you find the lock (with keyhole).
secondly, open the door and remove the 15 mm diameter plastic cover near the handle. Insert a long torx scrwdriver(T25 ?) in the
opening and while keeping the door handle "open" (this gives you the possibility to easily replace the handle later) Turn the torx until it stops
(do not use much force). Now you can pull out the metallic lock, peer
out the small white plastic under the door handle and pull out the handle. Do not turn the torx before you have replaced the handle.

In the case of back door, you start by finding the hole for the torx under the doors rubber sealing near the door handle.

Jan 08, 2013 | Volvo S60 Cars & Trucks

1 Answer

How do you replace the driver's side door handle on a 1998 VW Jetta


There is only one screw holding the door handle in, the screw is right on the inside of the door. Its right above where the door attaches to the door.

Jan 08, 2013 | 1998 Volkswagen Jetta

1 Answer

How to remove exterior door handle 2011 vw jetta


Open door and look where striker is,just above striker towards outer door is a black plastic insert,remove that,looking inside the smaller hole is a little black bar,with a hook pull bar towards yourself,will only move very little,then go to outside of door and pull handle out like to open,and pull the stationary part of handle out,let go of handle,slide handle out towards back of vehicle.

Jan 18, 2012 | Volkswagen Jetta Cars & Trucks

1 Answer

How do you replace the driver's side door handle on a 1991 vw?


on this car there should be a black strip cover on the inside of door handle. take small screw driver and remove it starting from near lock cylinder, pry very gently and cover should come off, then gently peel the cover towards the front of the car until it is off. phillips screw is located in the rear of the door and at the front of the handle.

Mar 21, 2009 | 1991 Volkswagen Jetta

1 Answer

1994 vw jetta drivers door window crank inside handle removal(man


You'll see a small ring on the inside of the crank where it meets the panel. That ring holds the crank in place. To remove the handle simple push the ring up and the handle will slide right off. Depending on the position of the crank the ring might have to be pushed up down or sideways. Hope that helps.

Jan 19, 2009 | 1997 Volkswagen Jetta

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,235 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...