Question about Cars & Trucks

Open Question

Temperature guage sensor location on ford f650

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 31 Answers

SOURCE: engine temperature sensor located on a 1998 Ford Mustang GT

Left hand side (if facing it), behind distributor, above oil fill.

Posted on Apr 22, 2009

  • 169 Answers

SOURCE: sensor locations

air intake look at snorkel it could be part of mass air flow check intake for eng coolant

Posted on Aug 29, 2009

emissionwiz
  • 75822 Answers

SOURCE: Temp guage stays at cold.

it is near the thermostat housing

Posted on Jan 15, 2010

Testimonial: "Guy knows his stuff. Thanks George"

  • 59 Answers

SOURCE: Does anyone know where the

The sensor you're looking for is called the ECT Sensor(Engine Coolant Temperature). It is located on the left hand side of the engine(left hand is closest to bumper/right hand is closest to firewall) closer to the back(driver side of vehicle).

Posted on Mar 24, 2011

archaeology
  • 662 Answers

SOURCE: location of engine coolant temperature sensor

Automobiles: 2000 Ford Escort ZX2 4-cylinder 2.0L MFI DOHC

NOTE
The "left" side of the engine is the driver's side.

The Engine Coolant Temperature (ECT) sensor is a thermistor (a device which changes resistance or voltage as temperature changes). The sensor detects the temperature of engine coolant and provides a corresponding signal to the PCM (Powertrain Control Module - aka "the car's computer").

The ECT sensor is mounted in the following locations (small Ford engines):

1.8L engines: in the cylinder head
1.9L engines: threaded into the heater hose inlet pipe
2.0L engines: at the left rear of the engine

2.0L Zetec Engine

(1) Partially drain the engine cooling system using a clean container. If coolant is in good condition, retain for reuse.
(2) Disconnect the battery ground cable.
(3) Disconnect the electrical wiring connector from the engine coolant temperature (ECT) sensor.
(4) Remove the retaining clip and the ECT sensor.


12_5_2011_5_38_05_pm.jpg

Fig. 1 Escort ZX2 ECT sensor - The retaining clip is removed (at the solid arrow). Withdraw ECT sensor by gently wiggling/pulling in the direction of the dashed arrow.

To install:

NOTE
Coat the ECT sensor O-ring with clean coolant prior to installation.

(1) Replace the retaining clip and the ECT sensor.
(2) Connect the electrical wiring connector from the Engine Coolant Temperature (ECT) sensor.
(3) Connect the battery ground cable.
(4) Refill the engine cooling system. An inexpensive plastic "Radiator Funnel" will help with this task.

Posted on Dec 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Coolant temperature sensor location on 97 ford expedition


I believe they are located in the intake manifold somewhere. Make sure the one that tells the computer the coolant temp is ACTUALLY giving out the correct temperature. I had a bad one one time in a 1993 Ford F-150, 5.8L....... no check engine light came on but hard to start. The bad sensor was telling the computer it was 32 degrees F when it was almost 80 degrees outside.!!
Garbage in=Garbage out.

Here is a video link from Youtube. There are 2 sensors, 1 for the guage and the other tells the on-board computer how hot/cold the coolant is. The one for the guage has 1-wire and the other one has 2 wires.
Hope this helps, ask more if you need to. What kind of problem are you having? No heat inside? Guage needle not getting into the normal area?


1997 Ford Expedition 5 4L V8 Triton Engine Coolant Temperature ECT Sensor...

Oct 20, 2015 | Ford Cars & Trucks

1 Answer

1991 ford v6 4.0 engine


Sounds like the temperature sensor needs replacement. Guage failure is a probability, but more likely the temp sensor is a problem.

Mar 31, 2015 | Ford Cars & Trucks

1 Answer

FORD F650 CUMMINS 5.9 COOLANT TEMPERATURE SENSOR LOCATION


It will be at or near the thermostat housing.

Aug 01, 2013 | Ford Cars & Trucks

1 Answer

Does anyone know where the sensor is located on the zetec 2.0 engine that regulates the temperature guage?


The sensor you're looking for is called the ECT Sensor(Engine Coolant Temperature). It is located on the left hand side of the engine(left hand is closest to bumper/right hand is closest to firewall) closer to the back(driver side of vehicle).

Mar 23, 2011 | 1999 Ford Escort

1 Answer

92 crown vic - temperature guage on the dash is not working...


0900c152801e4775.gif

The temperature gauge sending unit is located in the front section of the intake manifold, just to the right of the alternator on the 4.6L engines. Got this from autozones repair manuals


Mar 16, 2010 | 1992 Ford Crown Victoria

1 Answer

2001 Ford F650 with 7.2 Cat deisel acceleration problem


Check your TPS Throttle positioning sensor. Sounds like it has a dead spot in it or it is failing. May also be a wiring harness issue or loose connection at TPS too! If its intermittent then it will soon go out completely. It should be located on your fuel pedal. Remove it and check it with an ohm meter. Check resistance all the way thru from 0-100 percent. When it is not working it should do nothing and show no resistance. When it is working the resistance value will increase and or decrease as you turn the sensor.

Feb 21, 2010 | 2001 Ford Super Duty F 450

1 Answer

Where is the AIT located on a ford focus 2007 Duratec HE, and if the water temperature sensor is disconnected how does the temp gauge work


I'll assume you mean the IAT (intake air temperature) sensor. And while i'm not very familiar with the exact motor in your vehicle, the sensors are generally mounted on the Intake tube from the air box to the throttle body, sometimes mounted on the air box itself, or possibly even built into the Mass Air flow sensor. Which will be mounted most likely on the air box before the intake tube.

There is more than one water temperature sensor. One is for the ECM and the other for the guages. If the ECM one is unplugged it won't affect the gauges.

Oct 22, 2009 | 2007 Ford Focus (3 Door) Hatchback

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...