Question about 1990 Toyota Pickup

Open Question

How can i remove the upper control arm of a 1994 toyota pickup, 2wd 4-cyl. ?

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 599 Answers

SOURCE: Remove and replace 1994 Toyota pickup starter

disconnect battery ..remove skid plate..remove battery/ignition wire from starter (2 nuts)..remove starter bolts(2 )

Posted on Nov 07, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to remove upper ball joint on driver side of an 1994 GMC Sonoma


The OEM ball joint is riveted into the upper control arm. There are two possible ways to replace the joint. You can purchase the entire upper control arm/ball joint assembly, which comes complete with the upper control arm bushings. This part costs about $150.00. You will also have to deal with the coil spring when replacing it this way. You can also buy just the ball joint for about $30.00. This will require that you drill out the rivets of the original ball joint and then bolt in the replacement with the bolts that are provided with it. The 2WD and 4WD versions are the same. See this link.


http://www.autozone.com/suspension-steering-tire-and-wheel/ball-joint-upper/gmc/sonoma-4wd/1994/6-cylinders-z-4-3l-tbi

Mar 18, 2015 | 1994 GMC Sonoma

1 Answer

1994 Toyota pickup / 4WD / 4 cyl. Replaced heater core. Checked heater control valve- working correctly. Filled system from upper hoses at firewall to fill heater core. Connected hoses. replaced...


you could try running engine and open top heater core hose highest point should bleed it fully, failing that look at manual should tell how much water is in system

Feb 01, 2011 | 1994 Toyota Pickup

1 Answer

Replace alternator for 1994 toyota 4 cyl. pickup diagrams/pictures etc?


I've found the bolt that the alternator pivots on to be not much fun. A small palm type ratchet has been helpful. Here's an online manual's alternator section: http://myweb.dal.ca/is353832/93fsm/charging/3generato.pdf

Jul 28, 2010 | 1994 Toyota Pickup

1 Answer

How to replace front shock bsorbers


This is for the 2WD model:

2-Wheel Drive
  1. Raise and support the front of the vehicle safely using jack stands.
  2. Using an open end wrench, hold the shock absorber upper stem to prevent it from turning, then remove the upper stem retaining nut, the retainer and rubber grommet.
c16056c.gif
Common front shock absorber mounting-2WD vehicles

  1. Remove the shock absorber-to-lower control arm retaining bolts and lower the shock absorber assembly from the bottom of the control arm.
  2. Inspect and test the shock absorber; replace it, if necessary.
To install:
  1. Fully extend the shock absorber stem, then push it up through the lower control arm and spring so that the upper stem passes through the mounting hole in the upper control arm frame bracket.
  2. Install the upper shock absorber nut and tighten to 100 inch. lbs. (11 Nm) on 1994 models 145 inch lbs. (16 Nm) on 1995 models, 54 ft. lbs. (73 Nm) on 1996 models, or 106 inch lbs. (12 Nm) on 1997-99 models while holding the stem with an open end wrench. Be careful not to crush the rubber bushing.
  3. Install the shock absorber-to-lower control arm retaining bolts and tighten to 20 ft. lbs. (27 Nm) on 1994-95 models and 54 ft. lbs. (73 Nm) on 1996 models, or 22 ft. lbs. (30 Nm) on 1997-99 models.
  4. Remove the jack stands and carefully lower the vehicle.

Nov 01, 2009 | 1998 Chevrolet S-10 Pickup

2 Answers

Location of knock sensor on 1994 toyota 22vre engine


The Knock sensor on a 22re is located under the intake manifold on the engine block. to the upper left of the oil filter. With is the passenger side of the engine. I believe it is yellow in color. Not do be confused with the oil pressure sensor which is close by. The knock sensor has a larger electrical connector. Good luck it can be hard to get to.

Apr 10, 2009 | 1994 Toyota Pickup

1 Answer

Bolts for upper control arm assy on 1987 DODGE RAM PICK UP


Don't remember the size but they are likely grade 8 bolts not general hardware store stuff. See if you can get them from a junkyard (they usually discard them or cut off with a torch when removing control arm.

Mar 23, 2009 | 1987 Dodge Pickup 2WD

2 Answers

Remove and replace 1994 Toyota pickup starter


disconnect battery ..remove skid plate..remove battery/ignition wire from starter (2 nuts)..remove starter bolts(2 )

Nov 07, 2008 | 1994 Toyota Pickup

Not finding what you are looking for?
1990 Toyota Pickup Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...