Question about 2008 Dodge Avenger

Open Question

2008 dodge avenger in limp mode - 2008 Dodge Avenger

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 141 Answers

SOURCE: 2008 Dodge Avenger window problem?

Sounds like u have a bad window regulator which is a system of channels and guide wires that move the window up & down. since i do not know the whole situation I would make sure the window channels are lubricated with silicone spray to make sure the window is not being held up on anything.

Posted on Jun 04, 2009

Ad
  • 1 Answer

SOURCE: Battery changing

Ok, trust me on this one, take the drivers side tire off and remove the forward inner fender panel. If you try it without removing the tire, it is just a royal pain.

Posted on Jun 10, 2009

  • 1071 Answers

SOURCE: 2008 dodge avenger. Will not move out of park.

ther is an electric solenoid in the shifter the fuse may have blown but if you have ever spilled anything sweet ,soda juice etc it will get sticky and gum up not letting it operate as designed check fuses first, if fuse is good then go to solenoid

Posted on Jul 21, 2009

  • 63 Answers

SOURCE: 2008 Dodge Avenger check engine light

Not sure if this will work for you but worth a shot. I own a 2005 dodge neon. I know the ecu's are different but maybe dodge was smart and made all the cars this way. Insert you key into ignition. Turn key forward until you are at the last position right before the car starts to crank over. Repeat this for a total of three times then on your digital odometer display, you will see a set of numbers displayed. this will be your code for the malfanction(s) that set your check engine light. Like I said, it might not work on your car but give it a shot. If not, rent an obdII scanner and get your codes. Then you know where to start looking to fix your problem.

Posted on Dec 17, 2009

sandman357
  • 236 Answers

SOURCE: Brake Fluid for 2008 Avenger

it's DOT 4 or DOT 5 check with your manual and sometimes it's even in the fluid fill cap.

Posted on Feb 22, 2010

Testimonial: "Quick response, guided me in the right direction. Thanks!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My lighting bolt light is on and my car is running rough and I'm not able to go over 10-15 miles.. I have a 2008 dodge avenger 2.4L engine.


it is limp mode
you will have to run the fault codes to determine the fault
the sign indicates electrical problems so check alternator , drive n belt and have a load test done on the battery

Dec 28, 2015 | Dodge Cars & Trucks

1 Answer

I was told my 08 dodge avenger was in"limp mode" ( doesn't excellerate as normal an won't do over 45) what do I need to do to repair this issue . thanks in advance.


Limp Mode is the result of an exceptional condition occurring. It provides the driver a very restricted driving mode to travel a limited distance,

One hopeful cause is that this has occurred when the car was first started. If it is then it is likely that the battery was weak and tripped the cars computer into the limp home mode. Some times the limp mode doesn't activate but a CK engine light comes on.

Make sure that the car is in a safe location. Make sure that the battery is charged. Remove the battery terminal for about a minute or two. Reinstall the battery connection. If the car starts normal and runs OK you can assume the battery voltage had dropped below an except-able level and tripped the limp mode. Replace the battery.

Nov 23, 2015 | Dodge Cars & Trucks

1 Answer

Give a direction to start testing


Hello,
I do a LOT of electronic work on these dodge's, among many other vehicles. Are you getting any codes currently? If so please list them for me to go over for you. Also, you can disconnect the pos. and neg cables and hold them together for 3 to 5 minutes, this is called a hard reset and will reset any learned values/codes/parameters the vehicle has learned. Should do away with the limp mode assuming there is no other issues in the vehicle.. Finally, any after market wheels or tires? please advise

Jun 25, 2015 | 2008 Dodge Avenger

1 Answer

1999 Avenger Limp Mode


Best thing to try and thats to fit a manual gearbox,You will need the dealer diagnostic software on this car to find the fault which could anything and everything from the computer to a wiring block connection with dirty connections

Jul 26, 2013 | 1999 Dodge Avenger

1 Answer

How do I get my 1998 dodge avenger out of limp mode


you need to know what caused the limp mode and repair it otherwise you won`t be able to get it out of limp mode.

Jul 06, 2011 | 1998 Dodge Avenger

1 Answer

My 1998 dodge avenger automatic will not shift out of second what will cause this the computer i hooked it up to just gave me these codes po733, po700, po734 the motor is a 2.5


code po700 is what the pcm gets from the tcm when there is a problem with the transmission-anywhere from fluid level, sensor, solenoid, tcm problem, or mechanical problem.
the situation you have with the car being in 2nd gear is called "limp-in" mode. so you can limp-in to a repair center.

Mar 02, 2009 | 1998 Dodge Avenger

2 Answers

In limp mode cant get out 96 dodge avenger ES V6


unhook the battery for about 15 minutes and hook it back up... that should reset it

Jan 23, 2009 | 1998 Dodge Avenger

1 Answer

1996 dodge avenger when cold, the transmission go in limp mode


Is the vehicle's Check Engine Light on? It should briefly light up when you turn the key on (before you start the engine) to show that the light is working correctly. Based on what I've read I believe you should have one or more trouble codes. A place like AutoZone will read the trouble codes for you for free, and you can look them up here - http://www.engine-light-help.com/generic-check-engine-light-codes.html

Dec 12, 2008 | 1998 Dodge Avenger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...