Question about 1995 Chevrolet Blazer

1 Answer

Torque for eshaust to manifold in GMC Jimmy 1995 4WD vin W

I have a leak from exhaust at joint with manifold; one nut is loose and I want to tighten it. It sounds like a **** and may I don't have to replace those gaskets yet.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 239 Answers

45 -55 lb

Posted on Jan 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torque specs for ball joints on 2000 gmc jimmy


Upper ball joint knuckle nut 60 ft lbs, lower ball joint knuckle nut 80 ft lbs....mounting nuts and bolts 17 ft lbs

Jul 12, 2014 | 1996 GMC Jimmy

1 Answer

What is the torque setting for 1999 ford 182 exaust manifold


Check this for 1996-1999 FORD 3.0L (182) V6 DOHC...
- Install the exhaust manifold with a new exhaust manifold gasket.
- Install the exhaust manifold retaining studs and tighten to 13-16 ft. lbs. (18-22 Nm) in the sequence illustrated.
Raise and safely support the vehicle.
Position the Y-pipe assembly using a new flange gasket and install all the retaining nuts and bolts loosely.
Starting at the front of the system tighten the Y-pipe to exhaust manifold nuts to 26-34 ft. lbs. (34-46 Nm).

- Tighten the converter to transaxle nut and bolt to 30 ft. lbs. (40.3 Nm). Tighten the converter outlet bolts to 26-34 ft. lbs. (34-46 Nm).

zjlimited_1988.jpg

Fig. Right side exhaust manifold mounting bolt tightening sequence-3.0L DOHC engine (click image for zoom)


zjlimited_1989.jpg

Fig. Left side exhaust manifold mounting bolt tightening sequence-3.0L DOHC engine (click over image for zoom)

Hope this helps (remember to rating this answer).

Oct 06, 2011 | 1999 Ford Taurus

1 Answer

WHAT IS THE TORQUE ON A 94 BUICK CENTURY 3.1 V6 ON THE INTAKE AND EXHAUST PUSH RODS?


Tightening sequence would be to tighten from the center most bolts to the outer most bolts.
Intake Upper Bolts = 18 lb.ft.
Intake Lower Bolts = 10 lb.ft.
Exhaust Manifold Nut = 12 lb.ft
Exhaust Manifold pipe = 22 lb.ft.
Exhaust Manifold Heat Shield = 18 lb.in.
Rocker Arm Torque Nuts = 18 lb.ft.

Hope this helped you ?? if you need more info, get back to me.....

Jun 16, 2011 | 1994 Buick Century

1 Answer

Torque spec on exhaust manifold for 2000 yukon xl


EXHAUST MANIFOLD BOLT TORQUE 2000 GMC Truck Yukon XL 1500 2WD 5.3L SFI 8cyl The Exhaust Manifold Bolt Torque

Exhaust manifold bolts (first pass) 11 Lb/Ft.Exhaust manifold bolts (final pass) 18 Lb/Ft.Exhaust manifold nuts 39 Lb/Ft.Exhaust manifold stud 16 Lb/Ft.Air injection reaction (AIR) Pipe to exhaust manifoldnuts 18 Lb/Ft.(AIR) Pipe to exhaust manifold studs 4 Lb/Ft.Exhaust manifold AIR pipe studs 4 Lb/Ft.Note:To torque bolts and nuts, start in center usingcrisscross pattern working outward.

May 07, 2011 | GMC Yukon XL Cars & Trucks

1 Answer

Need cylinder head torque specifications 2004 hyundai elantra


Install the cylinder head bolts. Starting at top center, tighten all cylinder head bolts in sequence as shown in illustration, using the Cylinder Head Bolt Wrench (09221 - 32001) or equivalent. Repeat the procedure, re-tightening all cylinder head bolt to the specified torque. (torque spec is Cold Engine 105-115 Nm (76-83 ft lb) )
. Install the timing belt tensioner pulley.
. Install the timing belt on the camshaft sprocket, making sure that the tension side is tightened by turning the camshaft sprocket in reverse, all timing marks are in alignment.
. Adjust the timing according to "Timing Belt"
. Install the rocker cover and tighten the bolts to the specified torque. Tightening torque: Rocker cover belt:

2.5-3.5 Nm (25-35 kg.cm, 2-3 ft. lbs.)

. Install the timing belt cover.
Install the new intake manifold gasket and the intake manifold. Tighten the nuts and bolts to the specified torque.
Install the new exhaust manifold gasket and the exhaust manifold. Tighten the exhaust manifold attaching nuts to the specified torque.
. Install the surge tank and tighten the nuts bolts to the specified torque.
. Install the power steering oil pump and bracket.
. Install the ignition coil.
. Install the air intake hose.
Connect the vacuum hose, fuel hose and water hose.
. Install breather hose.

Dec 22, 2010 | 2004 Hyundai Elantra

1 Answer

How to replace a waterpump on a 2001 olds alero 2.4 cam


Water pump is driven by timing chain idler and is mounted on the rear of the timing chain housing. Disconnect the neg. battery cable. Drain cooling system. Disconnect oxygen sensor connector.
Remove upper exhaust manifould heat sheild. Remove exhaust manifold brace. Remove lower exhaust manifold heat sheild. Loosen manifold to exhaust manifold spring loaded nuts. Remove radiator outlet pipe to water pump coverbolts. Disconnect exhaust pipe from manifold.
Pull down on the exhaust pipe to disconnect it from exhaust manifold bolts. Disconnect outlet pipe from oil pan and transaxle. If equipped with manual tranaxle, remove exhaust maifold brace. Leave lower radiator hose attached and pull down on radiator out look pipe to disengauge from water pump. Leave outlet pipe hanging.
Lower vehicle. Remove exhaustmanifold to cylinder head nuts. Remove exhaust manifold to cylinder head nuts. Remove manifould. Remove timing chain front cover. Remove timing chain tensioner. Remove bolts bolts securing water pump cover to cylinder block. Remove water pump to timing chain housing nuts. Remove water pump attaching nuts. Remove water pump and cover assembly. Separate componets as necessary.
WHEN INSTALLING WATER PUMP MAKE SURE YOU FOLLOW THE TIGHTENING SEQUENCES THAT AFFECT SEALING. My frist one I messed up and broke the pump so becarful.
Installation
If cover was separated from body during removal, join this componets with a new gasket and hand tighten bolts. Apply bearing grease to splines of water pump drive. Set body and assemble into position.
Install and hand tighten bolts securing cover to cylinder block. Install and hand tighten bolts securing cover to cylinder block. Installand hand tighten nuts securing body to timing chain housing. Lubracate outlet pipe "O" ring with antifreeze. (I use RTV) Connect outlet pipe. Install and hand tighten bolts. Tighten bolts and nuts to specification in the following sequence. I'll ad the torque spec. at the end but this is where if you tighten out of order something will break.
pump assembly to timing chain housing nuts.
pump cover to pump body bolts
pump cover to cylinder block bolts (Bottom Bolt First)
outlet pipe to cover bolts
To complete installation reverse removel procedure.
Torque specs are 19 in. or 26mm all except water pump cover bolts which are 124 in or 14Nm
I never torque the bolts just make sure there done in the right order.

Oct 19, 2010 | Oldsmobile Alero Cars & Trucks

2 Answers

How to change an exhaust manifold leak 7.5L


Right-Hand
Removal
  1. Remove spark plug heat shield (12A406).
  1. Remove distributor to spark plug wires (12286) using Spark Plug Wire Remover T74P-6666-A.
    1. Disconnect muffler inlet pipe.
    1. If equipped with secondary air injection, disconnect the secondary air injection check valve tube (9B480).
    1. Remove attaching bolts and right exhaust manifold (9430).
    1. Inspect joint faces for signs fo exhaust leaks, cracks or any defect that would make exhaust manifold unfit for use







Left-Hand Removal






1. Remove oil level indicator tube (6754).
  1. Remove spark plug heat shield.
  1. Remove distributor to spark plug wires using Spark Plug Wire Remover T74P-6666-A.
  1. Disconnect EGR valve to exhaust manifold tube (9D477). If equipped with air injection, disconnect the secondary air injection check valve tube.
  1. Disconnect muffler inlet pipe.
  1. Remove attaching bolts and exhaust manifold (9431).
  1. Inspect joint faces for signs of exhaust leaks, cracks or any defect that would make the exhaust manifold unfit for use.
Installation
  1. Clean mating surfaces of right exhaust manifold or left exhaust manifold and cylinder head (6049). Clean mounting flange of right exhaust manifold or left exhaust manifold and inlet pipe(s). Clean mounting surface for air injection tube or right exhaust manifold. Apply light film of Premium Long-Life Grease XG-1-C or -K or equivalent meeting Ford specification ESA-M1C75-B to right exhaust manifold or left exhaust manifold.
  1. Position right exhaust manifold or left exhaust manifold on cylinder head. Install attaching bolts and washers, starting at fourth bolt hole from front of each right exhaust manifold or left exhaust manifold. Tighten bolts to 34-47 Nm (25-35 lb-ft), working from center right to both ends.
    1. Position inlet pipes to right exhaust manifold or left exhaust manifold. Install attaching nuts and tighten to 34-47 Nm (25-35 lb-ft).
    1. Position the secondary air injection check valve tube and the secondary air injection tube gasket (9C435) at rear of right-hand exhaust manifold. Install attaching bolts and tighten to 19-25 Nm (14-18 lb-ft).
    1. Attach the secondary air injection manifold tube (9B449) to left-hand exhaust manifold fitting (located under EGR tube). Tighten nut to 30-40 Nm (22-30 lb-ft).
    1. Attach the secondary air injection check valve tube to rear of right-hand cylinder head. Tighten bolts to 75-85 Nm (56-62 lb-ft).
      1. Connect EGR valve to exhaust manifold tube to left exhaust manifold, if removed. Tighten nut to 53-72 Nm (39-53 lb-ft).
      1. Install spark plug heat shield and distributor to spark plug wires.
      1. Install oil level indicator tube to left exhaust manifold, if removed. Tighten nut to 13-24 Nm (10-18 lb-ft).
      2. Start engine (6007) and check for exhaust leaks.







b913da4.gif
28b39c6.gif
Hope this helps you...WF †

Mar 10, 2010 | 1996 Ford F250 Crew Cab

1 Answer

Ball joints


Alldata is usually the correct source of information tho recheck that it is showing ft lbs.
best way to find out exactly what it should be is to call your local dealer, ask for the parts guy and see if he will look up the correct torque for those bolts.

robert

Sep 25, 2009 | 1996 GMC Jimmy

2 Answers

How to replace the water pump on 1993 oldsmoblie achieva.


2.4 enigine is the harder of the 3 enignes. it will need a timing chain to be removed and a coolant tube in the back of the engine to be removed. this job on the book calls for almost 7 hours.

if its 3.3 or 3100 its alot easier.

3100 is just 4 10mm pulley bolts and 5 or 6 small 8mm water pump bolts.

3.3 is alittle more work, but same concept as 3100 engine. more owkr only cause its in a tighter area.

good luck,
michael

Apr 29, 2009 | Oldsmobile Achieva Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...