Question about 2004 Land Rover Range Rover

Open Question

How do i adjust headlight height on 2003 range rover

The beam is to high on my range rover headlights. can i adjust them manually.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1986 Answers

SOURCE: can the headlights on 2006 range rover be adjusted

Depends....
If your car is right hand drive and you're taking it to another location that is right hand drive, then it will be fine the way it is.
However, if your car is right hand drive and you take it to another location that is left hand drive, then you cannot use those headlights. The reflector and projector assembly of a right hand drive car is designed to throw more light towards the passenger side of the vehicle (where your road signs would be)
_________________
\_________________\__________________

Posted on Nov 04, 2009

Ad
  • 16 Answers

SOURCE: 87 Range Rover Classic High-beams are always on when headlights

There is a relay, and fuses. Some realys under lower facia panel driver side UK 87 models, however there were some variations so check under the bonnet too.

This does sound more like a short, if all relays are ok. Check the head light units and work your way back. The wiring in these are not the best in the world, plug at back of head light unit suspect too.

Do your lower driving lights common too, when you have the switch in ? Has some one been messing about with this wiring, runs down by air dam.

Works and electrical manuals online try here http://www.landroverweb.com/Land-Rover-Range-Rover-manual-pdf.htm

Posted on Jan 23, 2010

  • 366 Answers

SOURCE: how to fit angel eyes to a range rover sport

you are not suppose to remove the lens cover, they are glued on, but if you really want to do it, you can try and use a diy blade and separate the cover and the lens, but it is not reccomended,

Posted on Jan 24, 2010

Testimonial: "ok thanx for your help"

  • 1 Answer

SOURCE: 2003 range rover headlight wiper blade driver side won't go down

Replace the fuse for the "Headlight Cleaning" circuit in the fuse box located inside the glove compartment on passanger side front. It should be fuse number 28 with an Amp Rating of 30. See Owner's Manual under Fuses.

Posted on Jan 25, 2010

  • 366 Answers

SOURCE: DOES ANYONE KNOW HOW TO TAKE THE LENS COVER OFF A

here's one way of doing it: http://www.youtube.com/watch?v=imIiglkq7HA

althou a different car its basically the same procedure as with the diy blade i mentioned before http://www.youtube.com/watch?v=e6qiaockkU8

all lens covers are glued on, some you have to cut, some melt and some pry open

Posted on Jan 25, 2010

Testimonial: "THAX MATE VERY HELPFUL"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i adjust my headlights?


  • Always adjust lights with optical headlight aimer VAS 5107, using detailed aiming procedure and specifications
  • Low and high beams are adjusted simultaneously.
98971520



Left headlight (adjustment screws for right headlight are mirror image):
1 - Lateral adjustment 2 - Height adjustment
  • Access adjustment screws through hole in lock carrier (Phillips head or socket head).
  • Turn the adjusting screws for lateral adjustment -1- and height adjustment -2- until the correct setting is achieved.
NOTE: Where equipped, ensure equal movement/function of headlights during automatic headlight range adjustment.

Oct 19, 2010 | 2001 Volkswagen Passat

1 Answer

Drivers side headlight assy change, Nissan Sentra 2003, Front lens was cracked and old one became opaque instead of mirrorlike(fogged up).Is it hard to change?


Just unscrew the screws holding down the black tabs on top of the headlights and you have to gently pull the headlight out , be careful because the bottom of the headlight has a tab holding it in place (be patient might have to move it around to release the bottom tab). And do the opposite when putting the new headlights on. Even if the bottom tab breaks. the tabs on the top will old the headlight in place. Once it's changed, you'll need to re-aim the headlights...

The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 20, 2009 | 2003 Nissan Sentra

2 Answers

Adjust headlites on a 2003 outlander


There is a screw adjuster on the back side of each headlight, near the outer edge.
Here is a picture of its location, from front and rear:

e7694bd.jpg

Oct 17, 2009 | 2003 Mitsubishi Outlander

2 Answers

How to adjust headlight alignment on Audi A6 2003


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 07, 2009 | 2003 Audi A6

2 Answers

How do you make adjustments to a 99 bonneville headlights. Repairs were done to the front end and the headlights don't shine on the road now.


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 01, 2009 | 1999 Pontiac Bonneville

1 Answer

Adjusting a headlight on a 04 discovery11 how too


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Sep 26, 2009 | 2004 Land Rover Discovery

1 Answer

I need to set up and adjust xenon headlights for a BMW Mini Cooper S from scratch. Need instruction manual and what Uk regulations have to be met i.e distance/height etc


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Sep 02, 2009 | 2005 Mini Cooper

2 Answers

2003 volvo s60, how do i adjust headlights


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Jun 18, 2009 | 2004 Volvo S60

1 Answer

Headlight adjustment 1999 S70


on each headlamp assembly, there will be either one or two plastic nuts that you can turn.

If you only have one nut on each, that will adjust the vertical aim of the headlights.

If you have two nuts on each, one will adjust the vertical and the other will adjust the horizontal.

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

Aug 18, 2008 | 1999 Volvo S70

1 Answer

Headlights


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Aug 01, 2008 | 2005 Acura MDX

Not finding what you are looking for?
2004 Land Rover Range Rover Logo

Related Topics:

122 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76673 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...