Question about Cars & Trucks

Open Question

How to replace clutch master cylinder Ford Econovan Maxi

2l petrol 5sp man

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
hank5899
  • 151 Answers

SOURCE: 97 chevy cavalier 2.2l 5sp clutch problem

get the hyd clutch system assembly complete and pre-bleed from the dealer

Posted on Sep 07, 2008

Ad
  • 1596 Answers

SOURCE: How do I bleed the clutch master cylinder

Same as You Bleed Any other System Being carefull not to get air IN and IT sometimes TAKES FOREVER ________ STICK WITH IT ------ Took Me 2 hours One time

Posted on Jan 19, 2009

  • 10 Answers

SOURCE: ford focus st170 clutch master cylinder

To replace the clutch master, you must remove the under hood fuse box and air filter housing assm, then remove the hydraulic line that goes into the inlet port of the clutch master, then inside the car, remove the hush panel/knee bolster panel from under the steering column, and loosen the boilts that retain the brake pedal to the firewall, then remove the two 10mm bolts that secure the clutch master to the brake pedal assm. Reverse procedure ti install, then fill the brake master cylinder with clean fluid, loosen the bleeder screw at the top of the trans, and bleed the clutch as you would the regular brake system, but never pump the pedal, tighten screw, with foot off of clutch pedal open screw and press pedal to floor, then tighten screw before you release pedal, then release pedal loosen screw, etc. until no more air comes out, it may take quite a few times to fully bleed the system.

Posted on Feb 07, 2009

DAD5bbbbg
  • 111 Answers

SOURCE: Clutch will not Engage

You need to bleed it out. It takes some time to do this. There is a bleeder valve above the hose fitting on the tranny. Have some one pump the clutch and hold it down and crack the bleeder nut. Just like you would when you do your brakes.

Posted on Apr 05, 2009

  • 70 Answers

SOURCE: no clutch pedal been bleeding it for 3 days

these are notorius for clutch bleeding problems, there is no good answer other than to keep pumping that pedal, eventually it will bleed out

Posted on Dec 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the master cylinder in a Ford Econovan


You must spray the brake lines with liquid wrench and let them soak for an hour then Just unbolt the lines amd move them out of the way unbolt the master cylinder and remove it you must bench bleed the new one to get the air out then install it and attach the lines then bleed the system starting with the wheel farthest from the master cylinder

Nov 25, 2016 | Ford Cars & Trucks

1 Answer

How to replace clutch master cylinder Ford Econovan Maxi 1993 without pulling the entire dash out?


Wait. Maybe you're in the wrong place. All cars I have seen have the clutch master cylinder bolted to the firewall inside the engine compartment. You take off the line going to the clutch, remove two bolts or nuts holding the unit to the firewall; and remove the unit. The only thing maybe to remove under the dash is the pushrod from the clutch pedal to the master cylinder.
Now if yours is different, then proceed, but check under the hood for the clutch master cylinder first.

Nov 02, 2012 | Cars & Trucks

1 Answer

Replaced master cylinder in clutch in an attempt to stop the car sticking in gear and moving when foot taken of brake. It still moves while the clutch is still depressed and needs brake to stop...


Sounds like a worn-out clutch plate or broken/damaged throw-out bearing or pressure plate. You need to replace the clutch - including the pressure plate, throw-out bearing, pilot bearing, and I also recommend a new slave cylinder. (Especially since you have allready replaced the master cylinder.) You may want to weigh the pros and cons of having your flywheel machined or just replacing it with a "Remanufactured " flywheel.

Mar 13, 2011 | Volkswagen Golf Cars & Trucks

2 Answers

Whats the gap on the points of a 1991 ford econovan swb ? Think its a 1800 or 2000, Thanks


The 1991 vans did not have points, they have a fully electronic igntion system.

Feb 12, 2011 | Ford Econoline Cars & Trucks

2 Answers

Valve clearances for a ford econovan 1.8lt, 1990


what are the valve clearance specs for a 1990 ford econovan maxi

Mar 14, 2010 | 1989 Ford Econoline

1 Answer

Where is the clutch fluid reservoir


if it's a hydralic clutch, then it's shared

May 30, 2009 | 1996 Ford Econoline

1 Answer

Nissan clutch problem


If your not able to shift into any gear that means your clutch is not engage/disengaging. Check for fluid leaks, you said topped off and fluid levels were low? It sounds like you have a Slave cylinder or master cylinder leak, if its leaking its bet to replace both.

Apr 27, 2009 | Nissan Sentra Cars & Trucks

2 Answers

97 chevy cavalier 2.2l 5sp clutch problem


get the hyd clutch system assembly complete and pre-bleed from the dealer

Sep 03, 2008 | 1997 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...