Question about 1998 Isuzu Trooper

1 Answer

No hot air from heater

Engine is hot. Heater radiator is not clogged. Heater blower works in all positions (floor, defrost, etc..). Temperature control knob rotates freely.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 444 Answers

Replace the termostat,

Posted on Nov 03, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 261 Answers

SOURCE: Heater Fan/Blower does not work.

what you need is a blower motor resistot

Posted on Dec 04, 2008

  • 19 Answers

SOURCE: Heater Blower won't work

There was a bulletin reguarding water contaminating the blower motor, which overheats the blower resistor and renders it inoperative. The fix was to replace the blower and the resistor and seal the culprit hood cowl screw at the base of the windshield, which is the second screw from the passenger side. They say water drips off of it down into the fresh air opening.
Here's what I'd do: Assuming your switch and blower motor is good, replace the blower resistor. Remove the blower motor and see if it spins without any excessive drag. If it's okay, reuse it. If it's dragging, it will overheat your new resistor in a short period of time and you'll be back at square one. The blower resistor is mounted to the front of the case with 2 screws to the left of the blower motor. Remove the glove box and you'll see it.
The Hood cowl screw is straight down into the cowl, the second one from the right side, about 10-12 inches from the right fender. Pull it out, put some sealer on it, and reinstall it.

Posted on Oct 02, 2009

Danniboi
  • 1098 Answers

SOURCE: 1992 Isuzu Rodeo Heater only blowing cold air

Thermostat! or blockedf heater matrix, no idea where the thermostat is on that car never worked on one.

hope this helps

Posted on Jan 15, 2010

Elradiuzi
  • 127 Answers

SOURCE: AC/Heater controller is not working. It is stuck

Yes it should. The assembly should have a few wires plugged into the rear of the unit. It's plug and play.

Posted on Jun 28, 2010

duane_wong
  • 6826 Answers

SOURCE: my heater doesn't seem to

If it's not blowing out hot air, the blend door may be the problem on the 1990 Isuzu Trooper.

Heater Water Control Valve REMOVAL & INSTALLATION On early models the heater control valve was part of the heater core inlet. To replace the control valve, remove the heater core as outlined in this section. Remove the control valve from the heater core, being careful not to damage the core. Use new gaskets when installing new valves. The remainder of the vehicles are not equipped with heater water control valves. They use heater unit doors to regulate the amount of heat entering the vehicle. --- I would check that both tubes running to the heater core are getting hot. If they are, then there is a blend door problem. If both tubes are not getting hot, the heater core is blocked somewhere or the heater control valve, if so equipped, is in need of replacement. Good luck on this repair. prev.gif next.gif

Posted on Oct 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need pitcure of vaccum lines on 1999 Ford Ranger v6 3.o air and heat blows only threw the defroster.


26392097-cvaukpwazi2vnl4fgradjhua-2-2.gif

Item Part Number Description 1 18A318 Vacuum Control Motor-, Panel/Defrost Door 2 18A478 Panel/Defrost Door (Full Vacuum Position) 3 - Defrost Air Flow 4 - Side Window Demister Air Flow 5 18B545 Temperature Blend Door (Full Heat Position) 6 19860 A/C Evaporator Core 7 19A813 Air Inlet Duct Door (Full Vacuum Position) 8 - Outside Air Inlet 9 18A318 Vacuum Control Motor-, Air Inlet Duct Door 10 - Recirculated Air Inlet 11 18527 Blower Motor 12 19A566 A/C Vacuum Reservoir Tank and Bracket 13 - Vacuum from the Engine Intake Manifold 14 19B888 A/C-Heater Function Selector Switch 15 - Vacuum to the 4x4 Hub Solenoids 16 18495 Water Diverter Valve (Full Vacuum Position) 17 18476 Heater Core 18 18A559 Floor/Panel Door (Full Vacuum Position) 19 - Floor Air Flow 20 18A318 Vacuum Control Motor-, Floor/Panel Door 21 - Panel Vent Air Flow

Dec 09, 2016 | Ford Ranger Cars & Trucks

3 Answers

1999 ford expedition , runs good doesn't overheat , but puts out no heat ?


heater core might need replaced . check the hoses going to it under the hood after it gets to operating temperature .One should be hot and the other not so much

Nov 19, 2015 | Ford Cars & Trucks

1 Answer

Heat stopped working in 2000 pontiac sunfire


With blower on high and tempature to max heat check to see if you have good air flow in all mode selections (defrost, vent, floor etc.). If so and you still have no heat then check heater core hose going from engine to inside car to heater core with vehicle running and coolant tempature about half on guage. If both hoses are hot and coolant in radiator/overflow bottle is full then hot cold blend door is stuck in cold position. If coolant level is low you will get no heat, check coolant level first.

Dec 18, 2011 | 2000 Pontiac Sunfire

1 Answer

The heater stays on the floor will not go to defrost


294653.gif



Could be faulting acutar motor for the hot air door. stocks5958.gif (1) Heater Core Cover (2) Heater Core (3) A/C Defroster Seal (4) Upper HVAC Module Case (5) Dash Seal (6) A/C Valve (7) Heater/Defroster Valve (8) Temperature Valve (9) A/C Valve Lever (10) Mode Valve Actuator (11) Heater/Defroster Valve Lever (12) Mode Valve Cam (13) Lower HVAC Module Case (14) Rear Heater Duct Seal (15) Temperature Valve Actuator Screw (16) Temperature Valve Actuator (17) HVAC Module Wiring Harness (18) Blower Motor Resistor/Relay Assembly (19) Blower Motor Acoustic Insulator (20) Blower Motor (21) Blower Motor Fan (22) Passenger Compartment Air Filter Access Door (23) Dash Seal (24) Evaporator Block Seal (25) Evaporator Core (26) Passenger Compartment Air Filters (27) Air Inlet Valve (28) Air Inlet Housing (29) Air Inlet Housing Seal (30) Air Inlet Actuator (31) Heater Core Pipe Seal

Dec 28, 2010 | 1999 Chevrolet Silverado 1500

2 Answers

Temperature gauge goes up blower motor works but absolutely know warm let alone hot air and its cold in michigan.


The first thing I would check is the level of antifreeze in the radiator. If it is low, you need to find out why. Hose or water pump leaking, blown head gasket, etc.

If it is not low, possible air mix door malfunction or clogged heater core.

Dec 09, 2010 | Ford Freestyle Cars & Trucks

3 Answers

I put a brand new heater core, radiator, water pump an thermastat but it still takes forever to blow heat out an then it doesn't get that hot.. what's the problem? my vehicle is a 1995 jeep wrangler 2.5 4...


Could be the heater bypass valve is stuck or the heater core is blocked.
I'd check the heater core first.You may have trapped air in the cooling system or the heater core may be partially plugged up. Engine coolant is delivered to the heater core through two heater hoses. With the engine idling at normal operating temperature, set the temperature control knob in the full hot position, the mode control switch knob in the floor heat position, and the blower motor switch knob in the highest speed position. Using a test thermometer, check the temperature of the air being discharged at the HVAC housing floor outlets.
Temperature Reference
Ambient Air Temperature 15.5° C (60° F) 21.1° C (70° F) 26.6° C (80° F) 32.2° C (90° F)
Minimum Air Temperature at Floor Outlet 52.2° C (126° F) 56.1° C (133° F) 59.4° C (139° F) 62.2° C (144° F)
If the floor outlet air temperature is too low, Both of the heater hoses should be hot to the touch. The coolant return heater hose should be slightly cooler than the coolant supply heater hose. If the return hose is much cooler than the supply hose, locate and repair the engine coolant flow obstruction in the cooling system.
OBSTRUCTED COOLANT FLOW
Possible locations or causes of obstructed coolant flow: Pinched or kinked heater hoses. Improper heater hose routing. Plugged heater hoses or supply and return ports at the cooling system connections. A plugged heater core. If proper coolant flow through the cooling system is verified, and heater outlet air temperature is still low, a mechanical problem may exist.
MECHANICAL PROBLEMS
Possible locations or causes of insufficient heat: An obstructed cowl air intake. Obstructed heater system outlets. A blend door not functioning properly.
TEMPERATURE CONTROL
If the heater outlet air temperature cannot be adjusted with the temperature control knob on the A/C Heater control panel, the following could require service: The A/C Heater control. The blend door actuator.
The blend door. Improper engine coolant temperature

Dec 04, 2010 | 1995 Jeep Wrangler

1 Answer

2006 grand prix heater only blows cold air. both heater hoses are hot blower motor works fine.


Sounds like the temperature blend door actuator may be bad or the vacuum hose to it is disconnected.

Poor Heater System Performance CAUTION
Check all fluid levels and adjust as needed, before operating vehicle for extended periods at idle.
  1. Start the engine.
  2. Idle the engine until the thermostat opens (upper radiator hose will be hot) Is the engine at normal operating temperature (approx. 200° F)? If yes, go to the next step. If no, go to step 16.
  3. Set the mode selector to FLOOR mode.
  4. Set the heater control selector to the warmest temperature setting.
  5. Set the blower speed the lowest setting.
  6. Carefully feel the inlet and outlet heater hoses at the heater core. Is the inlet heater hose significantly hotter than the outlet heater hose? If yes, go to step 14. If no, go to the next step.
  7. Set the mode selector to PANEL mode.
  8. Select the maximum blower speed.
  9. Select the warmest temperature setting.
  10. Place a thermometer into the center I/P PANEL air outlet and affix a second thermometer to the heater core outlet heater hose.
  11. Record the temperature at the center I/P PANEL air outlet and at the heater core outlet heater hose. Are the two temperature readings about equal? If yes, go to the next step. If no, go to step 13.
  12. Inspect and repair the cowl, cowl area, recirculation door, and the HVAC evaporator/heater core case for cold air leaks. Repair any problems found, go to step 17.
  13. Inspect the temperature door operation. Repair any problems found, go to step 17.
  14. Turn OFF the engine. Back-flush the heater core. Start the engine. Select the FLOOR mode and the lowest blower speed. Select the warmest temperature setting. Feel the temperature of the inlet and outlet heater hoses at the heater core. Is the inlet heater hose feel significantly hotter than the outlet heater hose? If yes, go to the next step. If no, go to step 17.
  15. Replace the heater core. When the repair is completed, go to step 17.
  16. Check for low engine temperature problems, Repair or replace as needed, go to step 17.
  17. Operate the system in order to verify the repair. If the system operates properly, the repair is complete. If the heater still does not work properly, repeat the entire procedure.

Nov 19, 2010 | 2006 Pontiac Grand Prix

2 Answers

Heater blows cold air. also, the temperature gage


A thermostat stuck in the open position can cause both of these problems

Nov 12, 2009 | 2002 Chevrolet S-10

2 Answers

I have a mercury mountaineer 2003 V6. It has a problem of making sound repeated when I want to have heat turned on. No sound when the dashboard A.C/Heat stays at AC level, which is the zero? level. The...


When the engine is cold,check the coolant level.

Make sure it's on max.

===

A coolant system should be flush every two years.

===

If you did a coolant flush recently then air pocket can be the cause of the un-even heating problem.

The DIY method is to drive you car onto a ramp or a steep hill.

Iet the engine cool off and top off the coolant tank.

Set MAX heat + MAX fan

Let the engine ran for 20 minutes wih the cap off and the trap air will escape from the coolant reserve tank,

Check coolant level and top off coolant when the engine cools down.



A shop will charge $75+ for this but using an air operated excavate tool!

========

A car with over 90K miles may experience linkage problem to the heater control valve.

The heater control valve (near the firewall) may be stick over time.

Open the hood and move the heater to max and min. Back and forth.

Clean and lube the linkage with WD-40 to free the heater control valve.

If it's a vacuum type heater control valve then cash for leaky vac. hoses.


=======
Move the fan switch back and forth to re-new the electrical conductors.

Pass a vacuum over the control panel to prevent dust build up behind the console.

Sep 13, 2009 | 2003 Mercury Mountaineer

1 Answer

I have the same problem with my windstar blower is fine but is coming cold air but no heat i dont know what to do can any one show me how to fix it thnx


First, feel the heater hoses going into the firewall under the hood. If they are hot, then you have hot engine coolant going into the heater core. If they are not hot, then you either have a bad thermostat or you are very low on engine coolant.

Next you need air flowing through the heater core so it can come out heated through your vents. If the iar is flowing somewhere else, your temp blend door is not moving because the bend door motor is bad or your temp knob on your heater controls is bad. The blend door motor is an electric motor.

------------------------------------------------
Air Flow Control
Air flow control is accomplished in the following manner:
  • Primary control is through the function selector knob , mounted on the heater function selector switch, which is part of the heater control .
  • The function selector knob has the following positions: OFF, PANEL, PANEL/FLOOR, FLOOR, FLOOR/DEFROST and DEFROST.
  • The heater function selector switch combines a vacuum selector valve with an internal electrical switch.
  • The vacuum selector valve directs source vacuum to various vacuum control motors (18A318) . Refer to the System Airflow Schematic and Vacuum Control Charts.
  • An internal single-pole electrical switch is also controlled by the selector. The switch controls the electrical supply to the heater blower motor switch (18578) .
  • The position of the function selector knob determines the manner in which the system will operate.
  • Each position of the function selector knob is detented for positive engagement.
Temperature Control
The temperature control operates in the following manner:
  • Temperature control of the heater system is determined by the position of the temperature control knob (between COOL-BLUE and WARM-RED) of the heater control .
  • This control knob is connected to a potentiometer mounted in the heater control . This potentiometer is electrically connected to the electric blend door actuator that operates the A/C air temperature control door.


e72a310.gif

  • Movement of the control knob from COOL (Blue) to WARM (Red) causes a corresponding movement on the air temperature control door and determines the temperature that the system will maintain.
System uses a reheat method to provide conditioned air to the passenger compartment.
  • All airflow from the blower motor (18527) passes through the A/C evaporator housing .
  • Temperature is then regulated by reheating a portion of the air and blending it with the remaining cool air to the desired temperature.
  • Temperature blending is varied by the air temperature control door, which regulates the amount of air that flows through and/or around the heater core (18476) , where it is then mixed and distributed.
--------------------------------------------------------------------------------------------------------------------------
inside you plenum box:

09f3f8a.gif

Mar 03, 2009 | 1998 Ford Windstar

Not finding what you are looking for?
1998 Isuzu Trooper Logo

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14384 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...