Question about Cars & Trucks

Open Question

Front axle nut torque specs for a 2004 dodge ram 3500 4x4

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
warlock61
  • 659 Answers

SOURCE: Axle nut torque spec

184 ft/lb

Posted on May 11, 2009

Ad
  • 7 Answers

SOURCE: front axle hub torque

Ram 1500 Pickup ...... 175 foot lbs. Then tighten until the cotter pin can be inserted. I had the same problem. I had to replace the inline check valves and I also had a bad hose. The check valves are not expensive.

Posted on Aug 14, 2009

Testimonial: "thanks for the help it was very useful"

canbruce75
  • 1776 Answers

SOURCE: I need the torque spec for the axle and the axle

Go to the autozone.com website and register there. It doesn't cost anything and you will have access to an online repair manual for the vehicle. (Kinda handy) They have a specification section, so the torque specs might be found there. Hope this helps and best wishes.

Posted on Aug 18, 2009

Testimonial: "hey thanks for the help"

  • 15 Answers

SOURCE: what are the front axle nut torque specs for a

185 ft.lbs

Posted on Oct 10, 2009

  • 11 Answers

SOURCE: torque spec for 2004 vibe front axle nut

Hello there is no specific torque on this nut torque it witch an inpact tool or a long bar and make sure to locked it witch a cutter pin or if there are a recess in your axle punsh the nut in the recess witch a punh.

Posted on Mar 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front Skf hub bearing torque spec 2003 dodge ram 2500 turbo diesel



Tighten the spindle nut to 149 ft-lbs to seat the bearing then
. rotate the axle 5 to 10 times to seat the hub bearing, then
tighten the spindle nut to a final torque of 263 ft-lbs I would just use a good impact gun to get it there.

Oct 15, 2016 | Dodge Cars & Trucks

1 Answer

Need torque specs for front wheel bearing on 2004 dodge 3500 dually


The hub bearing retaining bolts are 150 ft. lbs the center axle nut primary torque 135 ft.lbs rotate 5-10 times increasing torque by 50 ft.lbs until final torque of 265 ft.lbs is reached

Mar 23, 2014 | 2004 Dodge Ram 3500 Truck

1 Answer

Front hub torque specs


The torque for the hub bolts is 120 ft. lbs
The torque for the axle nut is 185 ft. lbs.

Dec 29, 2013 | Dodge Cars & Trucks

2 Answers

I need the torque specs for a 6 cyl 2004 Dodge Dakota 2 wheel drive- front wheel hub. In inch-lbs if possible.


Spindle nut. Tighten the nut to 185 ft. lbs. (251 Nm). Inch pounds is not an option, this critical torque spec is FT lbs.

Apr 26, 2011 | 2004 Dodge Dakota

1 Answer

I need the touque specs for the outer front axle nut on a 2005 dodge ram 2500 4x4


HUB AND BEARING ASSEMBLY NUTS TORQUE TO 125 FT LBS THE HALF SHAFT AXLE TORQUE TO 185 FT LBS.

Oct 16, 2010 | Dodge Ram 2500 Cars & Trucks

1 Answer

Replaced rear axle pinion bearing and seal, need to know pinion nut torque spec. for aam rear axle 2005 dodge 3500 4x4 Thanks.


There is no torque specs,this nut has to be tightened back like it was ,the best thing to do,was,to late now,is to use a torque wrench to remove the nut,and remember the torque,and when replacing it,torque it back to that spec,the reason being,there is a crush sleeve between the front pion bearing ,and the rear pinion bearing,and it has to be crushed to a certain amount,to aquire deepness into the ring gear,anyway just give it about 25 lbs torque,any more the crush sleeve will crush even more and the deepness of the pinion will be too much.

Apr 19, 2010 | 2005 Dodge Ram

1 Answer

I think my front Drivers side wheel bearing is going out on my 2004 dodge ram 1500 4x4. It is an ABS system. What should I do to replace this? I wouldnt mind doing it myself if its the cheaper route.


Remove the wheel, the brake caliper with the mounting bracket and pads all together, the brake rotor, and the axle nut. Make sure the axle is free inside the hub splines by pushing it in a bit. I believe this truck has 3 bolts for the hub/bearing assy. They remove from the inboard side of the knuckle, then the hub/bearing assy comes out. It may be corroded in the knuckle, so some force may be required to get it out. To reassemble, reverse the steps, being careful to torque the axle nut to the proper spec. Also pump the brake pedal before you road test to verify the noise is gone.

Jun 27, 2009 | 2004 Dodge Ram 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

227 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...