Question about Cars & Trucks

Open Question

Inner door panel removal passenger side 2004 chevy venture van

Window will not operate,checked fuses they check out OK !I need access to the inner door to check the window motor, but am hindered removing the panel after removing 2 screws and can find no others! please respond to davepatrick1968@gmail.com THANKS

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 42 Answers

SOURCE: 1991 Nissan Maxima: Removal of front driver side door panel

This is out of my haynes manual
1 disconnect negative battery cable
2 on manual window equipped modesl remove the window crank using a hooked tool to remove the retainer clip.
3 on power window equipped models pry out the armrest switch control plate and disconnect the electrical connections
4 detach the armrest pull handle retaining screw then remove the inside door handle trim bezel
5 insert a wide putty knife, a thin screwdriver or a special trim panel removal tool between the trim panel and the head of the retaining clip to disengage the door panel retaining clips.then remove the remaining door panel retaining screws at the lower edge of the door panel.
6 once all of the clips are screws are disengage detach the trim panel disconnect any electrical connectors and remoe the trim panel from the vehicle by gently pulling it up and out.
7 for access to the inner door remove the door panel support bracket then peel back the watershield taking care not to tear it. it install the trim panel first press the watershield back into place. if necessary add more sealant to hold it in place.
8 installation is the reverse of removal

Posted on Mar 20, 2009

Ad
  • 3 Answers

SOURCE: Removing a door panel on a 1988 chevy C15 truck

There should be a couple of screws on the arm rest that you need to remove and probably one on the door handle then you need to find something to pry the panel off with, without breaking the plastic clips. They make a special tool for this that you can buy for just a few dollars at any auto parts store. If attempting to do it without the right tool be careful not to break the clips.

Posted on May 15, 2009

honeymokey
  • 3113 Answers

SOURCE: Removing passenger door panel

There is a screw behind the lock rod. Lift door panel straight up to remove

Posted on Jun 13, 2009

  • 1986 Answers

SOURCE: need to remove the windows switch

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 1986 Answers

SOURCE: need to remove inner rear passenger side door

On the inside trim, you can remove screws (these screws may be covered by filler pieces or may be visible, or they may require you pry a plastic piece off that covers the screws) that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you need to pull back the weather seal and then you can access the bolts securing the outer handle

Posted on Nov 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2004 Chevy venture passenger window won't go up or down what could it be


Have you tried the drivers door "passenger door window switch" and the passenger "door window switch" to try and roll the passenger window up?When you do try to roll it up make sure the vehicle is running as you want the most voltage to the window motor.If both door switches would not roll the window up,try the following.
With the engine running hit the up window switch on the passenger door just as you give the door a HARD FIRM RAP.The window should roll up.It may take a few tries.DO NOT roll the window back down until you have changed or dissembled the window motor for a good cleaning.Also,check for broken wires at the door hinge area on both the drivers and passenger sides,pull each wire firmly looking for a broken wire.

Mar 26, 2015 | 2004 Chevrolet Venture

2 Answers

Passenger window will go down but not up


Check fuses but if other windows work fuse is good. May have come off track pull door panel and check.

Feb 20, 2013 | 2002 Chevrolet Venture Passanger

1 Answer

Chevy venture van passenger side AC blows cold, driver's side blows warm to hot


Usually a blend door problem, either the control or the blend door itself.

Jul 03, 2012 | 2000 Chevrolet Venture

1 Answer

2004 chevy venture: driver's electric window hesitates when trying to lower or raise it. Do I need to replace a switch, motor, etc.?


if you have fully charged battery and you are having this problem well i would take the door panel off and watch it operate make sure every thing is moving smoothly and lubed if you can switch the switches from passenger to drivers test both see if the drivers window operates normal same with other side if no change then yes find new motor on craigs list .com hope this helps you out

Jul 24, 2011 | 2004 Chevrolet Venture Passanger

1 Answer

Why does the rear power window doesn't work on my 2004 chevy venture


check for a blown fuse in the fuse center on passenger side end of dash. open passenger door and you should see a cover marked fuses and there should be sticker on the back of the cover telling you what fuse to check or check your owners manual.

Feb 06, 2011 | 2003 Chevrolet Venture Passanger

1 Answer

I recently purchased a used 03 Chevy Venture van. The passenger sliding door doesn't open. It worked for 1 week and stopped. The driver side sliding door has a broken handle so I'm able to open that door...


Pain but fixable. Sounds like the linkage is not connected. Even a mechanic will have to remove the door panel and fight with it. If you can remove the rear seat from the drivers side side door then you might have room to remove the passenger side door panel to fix it. Usually clips are the first thing to break on door handle/latch linkages

Apr 06, 2010 | 2003 Chevrolet Venture Passanger

1 Answer

How to install a window 2004 nissan 350z coupe?


Remove inner panel carefully. find 2 black circle stickers and raise glass to access 2 screws holding glass. Door vent does not need to be removed.

Jan 30, 2010 | 2004 Nissan 350Z

1 Answer

Passenger power window powers down not up


If you can do it, run a jumper from the drivers door to the passenger door. Unplug both motors. try to run the passengers door off the drivers switch to rule out the motor. I don't think it is because the motor is dc. But this is the common point. Please mark this as helpful or fixya. Shuold you have anymore problems, I used to be a mobile mechanic electircian. Looking forward to hearing from you.

Dec 31, 2008 | 2004 Chevrolet Venture Passanger

2 Answers

Location of a secondary air pump on a 2002 chevy venture


The A.I.R pump is located on the driver's side of the vehicle, just in front of the front tire. If you remove the tire & look at the inner fender well, you'll see that it's designed with a "trap door". Remove the screws that hold the door closed, then fold the door back to reveal the pump. What usually happens is the pump sucks in the sponge filter on the intake side & it lodges in the impeller blade...this causes the fuse to blow & eventually a code will set & the Service Engine Light will come on. The fuse is located under the hood in the black fuse box on the passenger side...the box should be clearly visible & easily accessable. Look for a 30A fuse, probably in location # 39.

Jul 28, 2008 | 1997 Chevrolet Venture

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

66 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...