Question about Cars & Trucks
Posted by Anonymous on
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: serpentine belt diagram:
The belt routing diagram is located on the top radiator cross member by the hood latch. You should see it when you open the hood. If it is not there, all Chrysler, Dodge, and Plymouth minivans, from 1993 to at least 1999, used the same 3.3L engine setup, so find someone with one and look for the diagram where I described.
Posted on Jul 18, 2008
SOURCE: belt diagram
start at power steering down to ac compressor to crank...around crank to belt adjuster....over fan pulley to alternator up from alt and over both idler pulleys....a 17mm 12point wrench will fit on adjuster to move it
Posted on Sep 25, 2008
On the 1999 Dakota with the 3.9liter, the fan shroud absolutely DOES NOT have to be removed. Very simple job. Simply use a breaker bar with a 15mm socket on the belt tesioner pulley nut. Using the breaker bar push (as though tightening) the pulley nut...the reaction will be that the tensioner removes tension from the pulley and the entire belt can be removed by easily slipping it toward the front of the vehicle...comes right off. The new belt can go back on in exactly the same manner. By the way the belt routing diagram IS CONVIENENTLY LOCATED between the hood latch and the radiator mounting for simple and quick refernce...one person job, I did removal and installation four times in less than 10 minutes. (why four times? The auto parts store was selling replacement belts that were too long and did not allow the belt tensioner to provide suffiecient tension...I had to try four different manufacturers before the tensioner was adequately tight with room to grow as the belt naturally stretches from use.). I found no stringing around the fan is required because of the way the belt is routed (it doglegs around the main engine pulley which is centered below the fanhousing and then the belt runs from there to the left side of the fan housing...avoiding the fan/fanhousing all-together (sure you can try to go past the fan/fan housing if you so desire...but you dont have to...and besides the space between the pulleys and the fan is ample to allow the belt to pass between with minimal interference or a simple rotation of the fan as you attempt this method. One hint that made my installs easy as pie...the last pulley you put it over should not be a bezeled and ridged pulley or you will needlessly make life difficult for yourself...the last pulley should be the water pump pulley which is a smooth bore and non-ridged pulley (makes you wonder how the belt even stays on it!)...making it easy as pie to slip it right over...as your last act of defiance to that mean old serpentine belt!
Posted on Jan 17, 2009
Looking at the engine from front (right side of the Van): Stating at the Top, Going Left to Right and Clockwise:
Over the Alternator
To under the Idle Pulley,
To Over the AC Compressor.
To the Left Side of the Water Pump.
To the Right side and Under the Crankshaft Pulley
To the Right side and Over and Down the Tensioner
To Under the Power Steering Pump
And Back up-to the Left side of the Alternator.
Advise when puting it on:
Put the Belt around everything else accept for the Alternator. After it is around all the rest of the Pulleys - Pull the belt up - tight from the Power steering Pump and the Idle Pulley to form a loop, holding the Belt close to the Altenator Pulley.
Using the 15mm wrench or belt tensioner bar - rotate the Tensioner Pulley towards the front of the Van and then place the belt over the Alternator.
Let me know if this helped or if you have additional information or questions. Feel free to contact me at FixYa.com!
Posted on Jan 22, 2010
Tips for a great answer:
Oct 12, 2017 | Dodge Cars & Trucks
May 18, 2016 | Dodge Cars & Trucks
Jan 02, 2015 | 2009 Dodge Journey
Aug 02, 2011 | Dodge Sprinter
Apr 20, 2011 | Mercedes-Benz Sprinter Cars & Trucks
Jan 06, 2011 | Mercedes-Benz Sprinter Cars & Trucks
Mar 09, 2010 | 2009 Dodge Sprinter Cargo
Sep 21, 2009 | 2004 Dodge Sprinter
33 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: