Question about 2000 Mercedes-Benz S-Class

Open Question

Entrance position do not drive

My S500 is showing an error which is Entrance Position DO NOT DRIVE, I've searched and they told pull it up down left and right and each time u pull wait for 10 seconds but nothing worked out. anyone had the same problem and knows how to solve it.

Posted by on


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 11800 Answers


That relates to the position of the steering wheel and seat - for an easier entrance in the car. Normally after that (when you close the door) they both should go to their programmed positions.
Try to reset the system by moving all the adjustable elements all the way up then all the way down - start with the steering wheel. If that fails to erase the warning then one of the position sensors has failed and it will have to be replaced. To identify it you will need to take the car to a dealer to have the error codes read.

Posted on Jun 26, 2011


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Driver's side key entrance linkage come loose inside of door. How to get to it(take window out)?

remove inside door panel and roll window up. You have to get skinny, but you can access it.

Mar 11, 2013 | 1995 Chevrolet C1500

1 Answer

I recently replaced the battery on my 2001 Toyota Solara, and now the computer won't reset so that I can pass inspection. I'm told that most cars reset after 100-300 miles of driving. I've...

this can take sometimes awhile here are some tricks
drive car 48-52 mph for about 10 miles pull over and idle
for 5 minutes and drive again keep fuel level between 1/4
and 1/2 as best as possible and do not warm up car too
long in the Am just a minute or 2 then drive gently good luck

Jan 01, 2018 | Cars & Trucks

1 Answer

I can't start the engine. The battery is almost fully charged. I need to turn the key for about 3 or more times to start the engine.

If you turn key to START position, what is the sound, is it;
1. no sound at all means maybe starter problem.
2. only heard Tik sound means starter problem (you can add relay but it will still happen in future)
3. crank sound but not start means battery weak.

You can also try to move gearshift to N instead of at P position before turn key to START. if it work mean your car safety switch at gearbox not know which gear you're on.

Jun 16, 2017 | 2009 Kia Picanto 1.1

1 Answer

2005 Ford Crown Victoria P71 Police Interceptor won't accelerate or shift into first gear

ok whats the governor? i have a 05 interceptor cv. my lights the dims and high beams keep clicking out. i checked the fuse under the dash and they are all good,and to work the highbeams i need to pull back on the blinker switch?

Sep 29, 2012 | 2005 Ford Crown Victoria

1 Answer

The hazzard light comes on everytime i open door. goes off a few minutes after i drive off. And I've noticed it goes off quicker when it's very sunny

is it the hazards or is the alarm going off look for a small button under the dash a push it with the key in the run position

Aug 12, 2012 | Cars & Trucks

1 Answer

Why can't anyone tell me what fuse to pull,after I put in freewheel position. now I need to turn on key for towing and steering.

No we can not tell you which fuse because there is no fuse to pull.
If you do an internet search for "tow a blazer behind an RV" you will find the procedure to put the transfer case in neutral and take it back out when you want to drive the truck. Its about 10 steps using the 4wd buttons on the dash.

Jul 27, 2012 | 2000 Chevrolet Blazer

2 Answers

How do you put it in low gear?

Pull the lever towards you them all the way down.

Jun 20, 2011 | 1998 Plymouth Voyager

2 Answers

I have a 93 Toyota Pickup that has a gas leak near the tank. Cant see where but fuel lines run to the tank and itt is in that area.

I've never had a problem with a sly leak-Usually I lose my gas tank driving over rocks, and you can see the remnants, or it's a cab-mount (No smoking, please!), but here's my advice: No matches! Take some water, add food colouring, and dump it on the tank. That way, the gas will push the water aside so you can see where it goes/comes from. My guess is right at the side facing front, or right up top, at the fuel vent or pickup line. Also check to make sure the fuel level sensor is tight, as is the fuel line entrance.

Jun 01, 2011 | 1993 Toyota Xtracab

1 Answer

Flashing prnds with 17090 error code

punch this code into google search and research the answers that show similar symptoms

Sep 13, 2009 | 2003 Audi A4 Cabriolet

1 Answer

Upon into a circular entrance to a freeway, going

your car is a hybrid and has a regeneration system which uses braking to drive mg2 which is recharging the battery.

Jul 11, 2009 | 2007 Toyota Prius

Not finding what you are looking for?
2000 Mercedes-Benz S-Class Logo

Related Topics:

902 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers


Level 3 Expert

77186 Answers

Joseph Prosser

Level 3 Expert

771 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides