Question about 1994 Dodge Intrepid

1 Answer

How to replace water pump in a 3.5 engine dodge intrepid 1994

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 14,384 Answers
Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: how do you replace a

The intake where the thermostat goes is in the driver side of the motor behind the altenator. I had to remove the front clip of the car and the altenator to get to it. It is quite a job.

Posted on Jul 31, 2008

  • 116 Answers

SOURCE: Need Diagram of water pump on a 1998 Dodge Intrepid 2.7,

the water pump is timing chain driven and to replace it requires serious disassembly of the engine. it is a 13 + hour job and is not for the casual mechanic

Posted on Apr 13, 2009

  • 2187 Answers

SOURCE: 1997 dodge intrepid running hot!

check first if you are loosing water or cooling fluids on your radiator. There may be a leak or the radiator cap may no longer prevent the steam from escaping. check the radiator fans if they are turning. You can check the fan if it is working by removing the temp sensor at the lower radiator hose. The fan should turn on by then.

Posted on Jun 22, 2009

  • 396 Answers

SOURCE: 1997 Dodge Intrepid 3.5L How to replace water pump

This a dificult and time consuming project. Suggest you purchase you a repair manual which gives you diagrams and detailed instructions for this type of repair. Difficult to explain procudure in writing.

Posted on Sep 10, 2009

  • 972 Answers

SOURCE: Dodge Intrepid 1996 Water Pump Replacement Needs

a timing belt. the water pump uses it to turn it and you got to take it off to change the pump anyway so you might as well get a new one.also the hydralic timing belt tensioner should be replaced at the same time just to be sure.you will need anti freeze of course as well

Posted on Apr 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace water pump 99 2.7


Hope this helps you....

Instructions
  1. Prepare the Dodge Intrepid
    • 1 Lay out a drop cloth underneath the Dodge Intrepid to protect the floor from coolant spills. Designate an area to lay out each part alongside its bolts and connecting hoses and wires. Use a drop cloth here as well, some of the parts will have traces of grease and coolant.
    • 2 Disconnect the negative battery cable, using a screwdriver to unscrew the clamp that secures the cable to the negative (-) post. Pull the cable away from the battery post.
    • 3 Use a jack to elevate the Dodge Intrepid and jack stands to shore up the jack. Release the pressure in the radiator by removing the cap. Take out the drain plug located underneath the radiator. Catch the coolant in a resealable container
    • 4 Use a grease pencil to mark on the timing belt its position in each pulley before removal. This will save time when reinstalling. If needed, replace the timing belt and skip marking the old one.
    Remove the Damaged Pump
    • 5 Locate the water pump on the Dodge Intrepid. It's mounted on the front of the engine block and connected to the radiator and various other parts through a series of hoses. It's rotated by the timing belt. Study these parts, as you'll have to remove them.
    • 6 Disconnect or remove the parts in front of the water pump, using an adjustable wrench. In the most common Dodge Intrepid engine--the 2.7L--you'll find, in order: the upper radiator crossmember, fan module, accessory drive belts, crankshaft damper, timing cover, timing chain and guide wires.
    • 7 Unbolt the water pump from the engine block, using an adjustable wrench. You may have to use a chisel to gently break the seal between the mount and the pump. Discard both the pump and the bolts.
    • 8 Clean off the mounting area with a shop rag.
    Install the New Pump
    • 9 Inspect the new water pump to ensure it's identical to the old pump and free of any metal splinters or debris.
    • 10 Arrange the new water pump on the mount. You won't need sealant for the o-ring on a Dodge Intrepid. Hold the water pump and o-ring in place as you secure it with the new bolts. Tighten them with a torque wrench to 105 inch pounds torque in any order.
    • 11 Install the timing belt and wires, using the grease pencil marks to guide you in installation. Install the rest of the parts in the order removed. The camshaft must be reconnected with a torque wrench at 125 foot pounds torque.
    • 12 Replace the radiator's drain plug and refill the radiator with the amount and type of coolant specified in your owner's manual. Release the jack and jack stands.
    • 13 Attach the negative battery cable to the post and tighten the screw on the clamp. Crank the Dodge Intrepid's engine and check for leaks. Then, close the hood.

Read more: How to Install a Water Pump in a Dodge Intrepid ' eHow.com http://www.ehow.com/how_4508707_install-water-pump-dodge-intrepid.html#ixzz29Q1ZC1uZ

Oct 15, 2012 | 1999 Dodge Intrepid

1 Answer

1999 dodge intrepid idles at 3000 rpm


Check your I A C motor (idle air control motor) Check all your hoses and tubes leading to and from. Check the throttle linkage itself to make sure nothing is obstructing it from returning to normal rpm,

Apr 01, 2012 | 1999 Dodge Intrepid

1 Answer

How do I replace the water pump on a 1999 Dodge Intrepid 3.2?


3.5L Engine To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain cooling system.
  3. Remove or disconnect the following:
    • Accessory drive belts
    • Engine timing belt
    • Water pump mounting bolts and note position of longer bolt for proper re-installation
    • Water pump body from engine
To Install:
  1. Apply Dielectric Grease or equivalent silicone grease to the O-ring. Install new O-ring on water pump.
  2. Position water pump to engine.
  3. Install or connect the following:
    • Mounting bolts
      1. Torque to 105 inch lbs. (12 Nm)
    • Timing belt
    • Accessory drive belts
  4. Fill cooling system.

Sep 18, 2010 | 1999 Dodge Intrepid

1 Answer

Dodge Intrepid 1996 Water Pump Replacement Needs


a timing belt. the water pump uses it to turn it and you got to take it off to change the pump anyway so you might as well get a new one.also the hydralic timing belt tensioner should be replaced at the same time just to be sure.you will need anti freeze of course as well

Apr 05, 2010 | 1996 Dodge Intrepid

1 Answer

HOW TO CHANGE WATERPUMP 1999 INTREPID 2.7


    Prepare the Dodge Intrepid
  1. Step 1 Lay out a drop cloth underneath the Dodge2_bing.gif Intrepid to protect the floor from coolant spills. Designate an area to lay out each part alongside its bolts and connecting hoses and wires. Use a drop cloth here as well, some of the parts will have traces of grease and coolant.
  2. Step 2 Disconnect the negative battery cable, using a screwdriver to unscrew the clamp that secures the cable to the negative (-) post. Pull the cable away from the battery post.
  3. Step 3 Use a jack to elevate the Dodge Intrepid and jack stands to shore up the jack. Release the pressure in the radiator by removing the cap. Take out the drain plug located underneath the radiator. Catch the coolant in a resealable container
  4. Step 4 Use a grease pencil to mark on the timing belt2_bing.gif its position in each pulley before removal. This will save time when reinstalling. If needed, replace the timing belt and skip marking the old one.
    Remove the Damaged Pump
  5. Step 1 Locate the water pump on the Dodge Intrepid. It's mounted on the front of the engine block and connected to the radiator and various other parts through a series of hoses. It's rotated by the timing belt. Study these parts, as you'll have to remove them.
  6. Step 2 Disconnect or remove the parts in front of the water pump, using an adjustable wrench. In the most common Dodge Intrepid engine--the 2.7L--you'll find, in order: the upper radiator crossmember, fan module, accessory drive belts, crankshaft damper, timing cover, timing chain and guide wires.
  7. Step 3 Unbolt the water pump from the engine block, using an adjustable wrench. You may have to use a chisel to gently break the seal between the mount and the pump. Discard both the pump and the bolts.
  8. Step 4 Clean off the mounting area with a shop rag.
    Install the New Pump
  9. Step 1 Inspect the new water pump to ensure it's identical to the old pump and free of any metal splinters or debris.
  10. Step 2 Arrange the new water pump on the mount. You won't need sealant for the o-ring on a Dodge Intrepid. Hold the water pump and o-ring in place as you secure it with the new bolts. Tighten them with a torque wrench to 105 inch pounds torque in any order.
  11. Step 3 Install the timing belt and wires, using the grease pencil marks to guide you in installation. Install the rest of the parts in the order removed. The camshaft must be reconnected with a torque wrench at 125 foot pounds torque.
  12. Step 4 Replace the radiator's drain plug and refill the radiator with the amount and type of coolant specified in your owner's manual. Release the jack and jack stands.
  13. Step 5 Attach the negative battery cable to the post and tighten the screw on the clamp. Crank the Dodge Intrepid's engine and check for leaks. Then, close the hood.

Apr 04, 2010 | 1999 Dodge Intrepid

1 Answer

How to adjust timing for 94 dodge intrepid


1st the belt must ALWAYS be replaced when the water pump is done or anytime the belt is distrubed, here are the only instructions I could find on the belt replacement.
http://www.allpar.com/fix/timingbelt35.html

Jun 18, 2009 | 1994 Dodge Intrepid

1 Answer

Water pump went out, just need to know where it is to replace it


It's mounted on the front of the engine blockmag-glass_10x10.gif and connected to the radiator and various other parts through a series of hoses. It's rotated by the timing belt. Study these parts, as you'll have to remove them.

May 27, 2009 | 1994 Dodge Intrepid

1 Answer

3 05 bolt patter on 96 intrepid for water pump


Really depends on the engine you have.

If you have a 3.3 L engine then the water pump is a 5 bolt pattern

If you have a 3.5 L engine then the water pump is a 3 bolt pattern.

Apr 23, 2009 | 2003 Dodge Intrepid

1 Answer

Need Diagram of water pump on a 1998 Dodge Intrepid 2.7,


the water pump is timing chain driven and to replace it requires serious disassembly of the engine. it is a 13 + hour job and is not for the casual mechanic

Apr 13, 2009 | 1998 Dodge Intrepid

Not finding what you are looking for?
1994 Dodge Intrepid Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...