Question about 2002 Chrysler PT Cruiser
What all do you have to take off to get to the oil pump?
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: pt cruiser aerial
At the base of the antenna, take a small crescent wrench or pliers and unscrew the antenna from the mounting bracket. Any Chrysler dealer should have a replacement antenna.
Posted on Oct 06, 2008
SOURCE: PT Cruiser Brake Light
The bulb in the rear light has burned out and to replace it follow these instructions: 1) go to your owner's manual to find out the part number. You can find and purchase the replacement bulb at Target, any auto parts store and even at Walmart for under $4.00; 2) pop open the trunk door; 3) get a phillips screw driver and unscrew the 2 screws holding the rear brake light fixture to your car body; 4) as soon as you turn over the fixture you'll see where to pull out the burned out bulb and replace it with the new one(s). Good luck!
Posted on Oct 15, 2008
This is the pressure light, nothing to do with the oil needing to be being changed, you have low oil pressure being indicated, this will destroy the engine if the light is really indicating low oil pressure, have the oil pressure tested with a mechanical test guage at a shop, if the oil pressure is ok then replace the oil pressure light sending unit.
Posted on Nov 23, 2008
Hi, i have put together a step by step guide that will help you with this replacement job. Make sure the vehicle is in a cool state before starting this job.
* Drain some coolant into a clean container until the coolant level is below the thermostat housing.
* Remove the upper radiator hose connection from the thermostat housing.
* Loosen the housing bolts and remove the housing.
* Remove the gasket and scrape it carefully from the surface of the housing and the mounting surface on the engine. If the gasket remains on either of the surfaces, there will probably bea coolant leak after reassembly. Some engines use a rubber O-ring to seal a thermostat housing.
* Compare the size of the thermostat to the old one. They are of different sizes, types, and temperature ratings.
* The temperature rating is stamped on the sensing bulb on the bottom of the thermostat. The temperature bulb faces the block.
* When replacing a thermostat, be sure that the thermostat fits into the groove in the block or outlet housing. If the thermostat is installed upside down, the engine will overheat.
* Install the gasket.
* Reinstall the thermostat housing. Refill the system and run the engine or pressure test to check for leaks.
* When the engine has reached operating temperature make sure the thermostat opens.
* You should be able to see coolant circulating within the radiator.
* Another way of checking thermostat operation is to feel the top of the radiator hose or use a thermometer or multimeter with a temperature probe to confirm that the coolant is warming up.
* If the engine is overheating, but the top hose is still cool to the touch, the thermostat is stuck closed and must be replaced.
When a paper gasket is used and the recess is in the thermostat housing, it is a good practice to position the thermostat into the recess and glue the gasket to hold it in place. If it falls out of its groove during installation, the outlet housing can be cracked or a coolant leak will result. Before tightening the water outlet housing, try to rock it back and forth to be sure it is flush. Housings are often cracked during this step.
Posted on Apr 30, 2009
Not for the beginner, I will be doing one on monday. 2001 Twin Cam.
I have been in repair for 30 years, I would not let anyone with less than 5 years experience touch it. This motor has the potential to bend valves if out of time between the cams and crank.
Changing the right side mount too. 10 hours according to the book (all data) and thats for someone that knows how.
Posted on Feb 28, 2010
Tips for a great answer:
Oct 08, 2014 | 2005 Chrysler PT Cruiser
Feb 01, 2014 | 2002 Chrysler PT Cruiser
May 29, 2010 | 2002 Chrysler PT Cruiser
Nov 23, 2009 | 2005 Chrysler PT Cruiser
Jan 02, 2009 | 2003 Chrysler PT Cruiser
1,027 people viewed this question
Usually answered in minutes!