Question about 1997 Oldsmobile Aurora

Open Question

Need torque specs on intake manifold on 97 olds aurora

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Dak408
  • 277 Answers

SOURCE: i need torque specs got ptatnum anmd intake for




Lower Intake Manifold
dak408_86.gif

15 Nm (11 ft. lbs
########################################################

Upper Intake Manifold

dak408_87.gif
10 Nm (89 in. lbs)
##########################################################

Posted on Nov 25, 2010

Ad
  • 1201 Answers

SOURCE: Torque Settings for 3.4L DOHC Intake Manifold and Plenum

10 ft lbs.

Posted on Mar 16, 2009

cadman000
  • 607 Answers

SOURCE: Need cylinder head and intake

1976 OLDSMOBILE TORQUE SPECS
455 CI cylinder head torque 85 ft/lbs
455 CI intake manifold torque 40 ft/lb

Hope this helps

Posted on May 07, 2009

  • 8 Answers

SOURCE: lower intake manifold gasket leaking 02 Olds Silhouette

This is basicly a very time consuming job rather than a physically hard one to complete. In order to replace the gasket you must remove the intake plenum,throttle body, and misc. vacuum hoses. The wiring harness connections must also be disconnected. Finally the intake manifold is exposed. The bolts holding the manifold to the block are removed exposing the leaking gasket. After removing the push rods and placing them in the correct order to be replaced the gasket and sealants can be removed. Finally replace everything in reverse order. Be sure to consult a GM manual for correct bolt torch specs. The correct specs for the manifold bolts usually come with the gasket. Make sure to change your oil a few times after this job in case any coolant entered the block. Also,change the thermostat and the oil seal on the distributor half shaft cap while you have everything off. Good Luck

Posted on May 12, 2009

  • 1244 Answers

SOURCE: Need torque sequence and torque specs for intake

bottom intake bolts torque 15-18 ft lbs from center and in criss cross pattern top plenum bolts 12-14 ft lbs

Posted on Jan 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Intake manifold torque specs 2000 olds silhoutte 3.4


Follow the link for a complete listing of this engines bolt torque specs. Torque Specs Database

Jan 25, 2017 | 2000 Oldsmobile Silhouette

1 Answer

The torque specs when replacing the inake gaskets on a 97 Lumina 3.1 liter enne


The torque specification is a 2-step process; tighten the vertical lower intake manifold bolts (the four middle ones) to 7 Nm (62 lb in). Tighten the diagonal lower intake manifold bolts (two on each end) to 7 Nm (62 lb in). Tighten the vertical lower intake manifold bolts (the four middle ones) to 13 Nm (115 lb in). Tighten the diagonal lower intake manifold bolts (two on each end) to 25 Nm (18 lb ft).

Upper Intake Manifold
Tighten Bolt/stud 25 Nm (18 ft. lbs)
Notice inch pounds and foot pounds. 62 inch pounds is 5.2 foot pounds.

Jan 05, 2017 | Cars & Trucks

1 Answer

98 ford windstar intake manifold torque specs


Intake torque specs ' FordForumsOnline.com

www.fordforumsonline.com > Ford Tech Forums > Engine & Drivetrain

May 7, 2010 - 2 posts - ‎2 authors
ISO torque specs for the intake & plenum for a 98 Windstar...3.8 with the ... Our community is here to help you with any questions you have related to your Ford. ... Lower Intake Manifold to Cylinder Head Bolt 8-12 - (71-106).

Torque Specifications - AutoZone

www.autozone.com/.../Ford-Windstar.../Specifications/Torque-...

AutoZoneAutoZone Repair Guide for your 2004 Ford Truck Ranger 2WD 2.3L MFI DOHC 4cyl Engine Mechanical Specifications Torque Specifications. ... Ford Windstar 1999-2003 ... Bolts, Main Bearing Bolts, Rod Brearing Bolts, Crankshaft Damper Bolts, Flywheel Bolts, Manifold. Intake, Exhaust ... Vehicle: 2008 Ford F150, 98 Civic.

Dec 21, 2015 | 1998 Ford Windstar

1 Answer

What are the torque specs on a 2002 toyota sienna's spark plugs, air intake manifold, and valve covers? Thank you.


Spark plug torque on the 3.0L engine is 13 ft.lbs. and the 3.3L is 18 ft.lbs.

Valve covers-69 inch lbs.

Intake Manifold-11 ft. lbs.

Jul 07, 2014 | 2002 Toyota Sienna

2 Answers

Need torque specs for a 2001 jeep cherokee intake manifold


Intake manifold using new gaskets. Torque the bolts, in sequence, to 105 inch lbs. (12 Nm)...

6a7ecad.jpg

Fig. Intake manifold torque sequence-3.7 & 4.7L engines


Hope this help (remember comment and rated this).

May 07, 2010 | 2001 Jeep Cherokee

1 Answer

How to replace a starter on an 97 olds aurora with a northstar 4.0


Not sure how different, but on the 2001 4.0 you remove the fuel rails and intake manifold. Starter is under the intake manifold. Not too difficult of a job.

May 06, 2010 | 1997 Oldsmobile Aurora

3 Answers

Need head bolt, intake manifold, and exhaust torque specs


Cylinder Head Bolt Step1- (25 FT.Lbs) Step2(45 Ft.Lbs) Step3(65Ft,Lbs).....Intake Manifold(35Ft Lbs)....Exhaust Manifold Center (20Ft Lbs) All Others (20 Ftlbs).....Thanks

Mar 06, 2010 | GMC Suburban Cars & Trucks

1 Answer

Torque Spec for '99 Chevy C1500 5.7L engine lower intake manifold


On 5.7L engines, install the bolts and torque in sequence as follows:
  1. Step 1: 71 inch lbs. (8 Nm).
  2. Step 2: 106 inch lbs. (12 Nm).
  3. Step 3: 11 ft. lbs. (15 Nm).
f2266b6.jpg

Mar 14, 2009 | 1999 Chevrolet C1500

Not finding what you are looking for?
1997 Oldsmobile Aurora Logo

Related Topics:

266 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...