Question about Cars & Trucks

Open Question

Code P0717 2003 ford sports trac - Cars & Trucks

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
chuck943
  • 783 Answers

SOURCE: 2007 FORD EXPLORER SPORT TRAC 4X4 Change oil light on

Press and hold the SELECT/RESET
control switch to select SYSTEM
CHECK when “SYSTEM CHECK /
HOLD RESET” is displayed in the
message center. Selecting this
function from the SETUP MENU
causes the message center to cycle through each of the systems being
monitored. For each of the monitored systems, the message center will
indicate either an OK message or a warning message for two seconds.
Pressing the SELECT/RESET control switch cycles the message center
through each of the systems being monitored.

The sequence of the system check report and how it appears in the
message center is as follows:
1. OIL LIFE RESET
2. CHARGING SYSTEM
3. WASHER FLUID
4. DOOR AJAR
5. EXTERIOR LAMP
6. BRAKE SYSTEM
7. PARK BRAKE
8. MILES TO EMPTY
9. FUEL LEVEL LOW (will only display if 50 miles or less to empty)
To reset the oil monitoring system to 100% after each oil change
[approximately 5,000 miles (8,000 km) or 180 days] perform the
following:
1. Enter SYSTEM CHECK to display
“OIL XXX% RESET IF NEW”.
2. Press SELECT/RESET control
switch to display “HOLD RESET IF
NEW OIL”.
3. Press and hold the
SELECT/RESET control switch for
more than 2 seconds. Oil life is set
to 100% and “OIL CHANGE SET TO
100%” is displayed.

Posted on Apr 02, 2009

Ad
  • 148 Answers

SOURCE: Ball joint replacement-2003 Ford Sport Trac

if you dont have a ball joint press and dont know how to use one then dont do it, but if you do its not that bad of a job just jack the truck up under the control arm remove the brake rotor then take the lower ball joint nut off then use a pickle fork to break the ball joint loose then take the axle nut off push the axle out of the bearing and use the ball joint press to remove and replace the ball joint

Posted on Jul 19, 2009

  • 1 Answer

SOURCE: 01 ford explorer sport trac rear timing chain diagram

They will not loan you the tools.....how else will they continue to rip off the average garage junkie and make lots of money?

Posted on Nov 18, 2009

  • 5 Answers

SOURCE: how to replace fuel filter on 2001 ford sport trac

Buy a manual and read it. The manual will tell you how to replace...

Posted on Nov 23, 2009

  • 7 Answers

SOURCE: how do i reset my keyless entry keypad code

You can call the ford dealer and give them your VIN and they can give you the code.

Posted on May 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace headlight bulb on 2007 ford explorer sport trac


How To Install Replace Headlight Ford Explorer Sport Trac ...

? 4:28
https://www.youtube.com/watch?v=NzMVcCsZ860
May 11, 2010 - Uploaded by 1A Auto Parts
How To Install Replace Headlight Ford Explorer Sport Trac 01-05 1AAuto. .... We offer the replacement headlights on our website for your truck.

Jan 11, 2016 | 2007 Ford Explorer Sport Trac

1 Answer

What will fix codes po320 & po446?


EOBD code Fault location Probable cause
P0320 Crankshaft position WiringCKP/RPM ,
(CKP) sensor/engine sensorECM
speed (RPM) sensor
circuit malfunction
,
EOBD code Fault location Probable cause P0446 Evaporative emission (EVAP) system, vent control - circuit malfunction Wiring, EVAP canister purge valve, ECM Hope that helps

Oct 19, 2014 | 2007 Ford Explorer Sport Trac

1 Answer

Ford keyless entry code


for the best solution of your problem visit this site
Best Manuals

Aug 06, 2014 | 2004 Ford Explorer Sport Trac

1 Answer

2007 Ford Sport Trac dashboard flashing engine code. What does this mean?


Hi Charles:
You will need to scanned the car computer to know exactly what fault code is stored there; note this code number and send us for additional details.

Sometimes Autozone or Autoshop with OBD scanner reader make this job for free, try it and keep us updated.

Dec 18, 2011 | 2007 Ford Explorer Sport Trac

1 Answer

Trying to find the door key code for a ford explorer sport trac 2003


You will have to take this one to the dealer. they can retrieve the code or put a new one in for you. call around because some of them will do it for free.
Randy

Nov 09, 2010 | 2003 Ford Explorer Sport Trac

1 Answer

What is code 171 and 174 on a 01 Ford Sport Trac


171 is system too lean (bank 1)
174 is system too lean (bank 2)
you might have a vacuum leak or bad injector o rings

Oct 08, 2010 | 2001 Ford Explorer Sport Trac

2 Answers

How do i reset my keyless entry keypad code for ford sport trac


You can call the ford dealer and give them your VIN and they can give you the code.

Nov 13, 2009 | 2005 Ford Explorer Sport Trac

1 Answer

What is code 51 on a 2005 ford explorer sport trac


What kind of code is that? Normally OBD-II codes are in the format p0051 or p1051. I'm going to guess it's a p0051?

Apr 10, 2009 | 2003 Ford Explorer Sport Trac

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...