Question about Cars & Trucks

Open Question

How do you change the throttle position sensor in a mack truck

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: Replacing A Throttle Position Sensor

the tps is attached to the throttle body. It operates the plate inside.

Posted on Dec 29, 2008

  • 54 Answers

SOURCE: Check engine light is on and high idle (1500rpm)

Check for a vacuum leak.

Posted on Feb 03, 2009

keemo68
  • 1263 Answers

SOURCE: how to install a throttle position sensor on 93' 4.3 chevy 1500 truck

the two bolts that hold the sensor are torqued to 18 inch pounds. other than that it's self adjusted through the ecm

Posted on Apr 30, 2009

c17hydro
  • 2984 Answers

SOURCE: where is the throttle positioning sensor located

Please don't forget to rate!



b487a12.gif
Disconnect and remove the TP sensor from beneath the throttle body


1d94cbf.gif
View of the throttle position sensor mounting-4.9L, 5.0L and 5.8L MFI engines shown, others similar



76a43b3.gif

Exploded view of the throttle body mounting-5.0L and 5.8L engines

Posted on Mar 06, 2010

c17hydro
  • 2984 Answers

SOURCE: changing throttle position sensor on a 2004

Removal & Installation

  1. Disconnect the negative battery cable.
  2. Disconnect the throttle position (TP) sensor electrical connector.
  3. Remove the screws and the TP sensor.

923d1f7.gif
Throttle position (TP) sensor electrical connector


b3a94a2.gif
TP sensor


To install:
  1. Install the screws and the TP sensor. Tighten screws to 7 inch lbs. (3 Nm)
  2. Connect the throttle position (TP) sensor electrical connector.
  3. Connect the battery ground cable.

Posted on Apr 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I solve for My Hyundai sonata model 2009 code P2110 , P2118 in scaning. I changed throttle body and TP sensor. after change of these even I am getting problem in accelerator not increases above


P2110...Faulty Throttle Actuator Control Module
- Throttle Actuator Control Module harness is open or shorted
- Throttle Actuator Control Module circuit poor electrical connection

P2118 - Electronic Throttle Control(ETC) system is made of the components throttle body, Throttle Position Sensor(TPS)1&2 and Accelerator Position Sensor(APS) 1&2. The throttle body contains the actuator, the throttle plate and the throttle position sensor (potentiometer), which are integrated in one housing. The actuator consists of a DC motor with a two-stage gear. The opening angle of the throttle valve is detected by the throttle position sensor which is mounted on the throttle body. And it provides feedback to the ECM to control the throttle motor in order to control the throttle valve opening angle properly in response to the driving condition.

Jan 06, 2015 | 2009 Hyundai Sonata

1 Answer

I need to know the code po120


Throttle Position Sensor/Switch (TPS) A Circuit Malfunction
The TPS (Throttle Position Sensor) is a potentiometer that is mounted to the throttle body. It detects the throttle blade angle. As the throttle blade moves, the TPS sends a signal to the PCM (Powertrain Control Module). Usually a three wire sensor: A 5 volt reference from the PCM to the TPS, a ground from the PCM to the TPS, and a signal return from the TPS to the PCM. The TPS sends the throttle position information back to the PCM on this signal wire. When the throttle is closed the signal is near .45 volts. At WOT (Wide Open Throttle) the TPS signal voltage will approach a full 5 volts. When the PCM sees a voltage that is outside of normal operating range, P0120 will set. NOTE: The PCM knows that any large change in throttle position means a cooresponding change in manifold pressure (MAP). On some models the PCM will monitor MAP and TPS operation for comparison. Meaning that if the PCM sees a large percentage change in throttle position, it expects to see a cooresponding change in manifold pressure and vice versa. If it doesn't see this comparitive change, P0120 may set.

Dec 11, 2014 | 2001 Toyota Sienna

1 Answer

Changed all sensors oc co etc etc still my truck is bogging when you accelerate


Year make and model ?
Did you replace the fuel filter and check fuel pressure ?

Aug 03, 2012 | Cars & Trucks

1 Answer

Where is the thorttleposition sensor on 2001jeep cherokee


The 3 wire Throttle Position Sensor (TPS) is mounted on the throttle body and is connected to the throttle blade.
The TPS is a 3wire variable resistor that provides the Powertrain Control Module (PCM) with an input signal (voltage) that represents the throttle blade position of the throttle body. The sensor is connected to the throttle blade shaft. As the position of the throttle blade changes, the resistance (output voltage) of the TPS changes.
The PCM supplies approximately 5 volts to the TPS. The TPS output voltage (input signal to the PCM) represents the throttle blade position. The PCM receives an input signal voltage from the TPS. This will vary in an approximate range of from .26 volts at minimum throttle opening (idle), to 4.49 volts at wide-open throttle. Along with inputs from other sensors, the PCM uses the TPS input to determine current engine operating conditions. In response to engine operating conditions, the PCM will adjust fuel injector pulse width and ignition timing.
The PCM needs to identify the actions and position of the throttle blade at all times. This information is needed to assist in performing the following calculations:

selectachapter.gif

Cherokee, Grand Cherokee, 1999-2005
Throttle Position Sensor

Print


Operation

The 3 wire Throttle Position Sensor (TPS) is mounted on the throttle body and is connected to the throttle blade.
The TPS is a 3wire variable resistor that provides the Powertrain Control Module (PCM) with an input signal (voltage) that represents the throttle blade position of the throttle body. The sensor is connected to the throttle blade shaft. As the position of the throttle blade changes, the resistance (output voltage) of the TPS changes.
The PCM supplies approximately 5 volts to the TPS. The TPS output voltage (input signal to the PCM) represents the throttle blade position. The PCM receives an input signal voltage from the TPS. This will vary in an approximate range of from .26 volts at minimum throttle opening (idle), to 4.49 volts at wide-open throttle. Along with inputs from other sensors, the PCM uses the TPS input to determine current engine operating conditions. In response to engine operating conditions, the PCM will adjust fuel injector pulse width and ignition timing.
The PCM needs to identify the actions and position of the throttle blade at all times. This information is needed to assist in performing the following calculations:


Ignition timing advance Fuel injection pulse-width Idle (learned value or minimum TPS) Off-idle (0.06 volt) Wide Open Throttle (WOT) open loop (2.608 volts above learned idle voltage) Deceleration fuel lean out Fuel cutoff during cranking at WOT (2.608 volts above learned idle voltage) A/C WOT cutoff (certain automatic transmissions only)


Removal & Installation

3.7L & 4.0L

  1. Disconnect TPS electrical connector.
  2. Remove TPS mounting screws.
  3. Remove TPS.

To Install:
The TPS is mounted to the throttle body. The throttle shaft end of throttle body slides into a socket in the TPS. The TPS must be installed so that it can be rotated a few degrees. (If sensor will not rotate, install sensor with throttle shaft on other side of socket tangs). The TPS will be under slight tension when rotated.
  1. Install TPS and retaining screws.
  2. Tighten screws to 7 Nm (60 inch lbs.) torque.
  3. Connect TPS electrical connector to TPS.
  4. Manually operate throttle (by hand) to check for any TPS binding before starting engine.

4.7L
  1. Remove air duct and air resonator box at throttle body.
  2. Disconnect TPS electrical connector.
  3. Remove two TPS mounting bolts (screws).
  4. Remove TPS from throttle body.

To Install:
The throttle shaft end of throttle body slides into a socket in TPS. The TPS must be installed so that it can be rotated a few degrees. If sensor will not rotate, install sensor with throttle shaft on other side of socket tangs. The TPS will be under slight tension when rotated.
  1. Install TPS and two retaining bolts.
  2. Tighten bolts to 7 Nm (60 inch lbs.) torque.
  3. Manually operate throttle control lever by hand to check for any binding of TPS.
  4. Connect TPS electrical connector to TPS.
  5. Install air duct/air box to throttle body.

Hope this helps

Dec 31, 2011 | 2001 Jeep Grand Cherokee

1 Answer

2003 Yukon Denali XLT lights flicker, rpm goes up and down when on park or stopped or driving and slow speeds. Sometimes it turns off. I thought it might be bad spark plugs or cables so I changed them and...


Your vehicle has electronic throttle control . Position sensor's in the gas pedal an the throttle body , inputs to the Throttle Actuator Control Module
The TAC module is the control center for the throttle actuator control system. The TAC system is self-diagnosing and provides diagnostic information to the PCM through a dedicated serial data line. The TAC achieves throttle positioning by providing a pulse width modulated voltage to the TAC as directed by the PCM.

The throttle actuator control (TAC) system delivers improved throttle response and greater reliability and eliminates the need for mechanical cable. The TAC system performs the following functions:
• Accelerator pedal position sensing
• Throttle positioning to meet driver and engine demands
• Throttle position sensing
• Internal diagnostics
• Cruise control functions
• Manage TAC electrical power consumption
The TAC system components include the following:
• The accelerator pedal position (APP) sensors
• The throttle body assembly
• The throttle actuator control module
• The powertrain control module (PCM)
Accelerator Pedal Position (APP) Sensor
The accelerator pedal assembly contains 2 individual APP sensors within the assembly. The accelerator pedal position (APP) sensors 1 and 2 potentiometer type sensors each with 3 circuits:
• A 5-volt reference circuit
• A low reference circuit
• A signal circuit
The APP sensors are used to determine the pedal angle. The control module provides each APP sensor a 5-volt reference circuit and a low reference circuit. The APP sensors then provide the control module with signal voltage proportional to pedal movement. APP sensor 1 signal voltage is low at the rest position and increases as the accelerator pedal is applied. APP sensor 2 signal voltage is high at the rest position and decreases as the accelerator is applied.
Throttle Body Assembly
The throttle body assembly consists of the throttle body, the throttle position (TP) sensors, and the throttle actuator motor. The throttle body functions similar to a similar to a conventional throttle body with the following exceptions:
• An electric motor opens and closes the throttle valve.
• The throttle blade is spring loaded in both directions and the default position is slightly open.
• There are 2 individual TP sensors within the throttle body assembly.
The TP sensors 1 and 2 are potentiometer type sensors each with 3 circuits:
• A 5-volt reference circuit
• A low reference circuit
• A signal circuit
The TP sensors are used to determine the throttle plate angle. The control module provides each TP sensor a 5-volt reference circuit and a low reference circuit. The TP sensors then provide the control module with signal voltage proportional to throttle plate movement. Both TP sensor signal voltages are low at closed throttle and increase as the throttle opens.

Flickering light's could be caused by a bad diode in the alternator . Fluctuating idle could be caused same alternator problem or dirty throttle plate.
Throttle Body Cleaning To Restore Idle Quality

Jul 15, 2017 | 2003 GMC Yukon

1 Answer

Changing throttle position sensor on a 2004


Removal & Installation
  1. Disconnect the negative battery cable.
  2. Disconnect the throttle position (TP) sensor electrical connector.
  3. Remove the screws and the TP sensor.

923d1f7.gif
Throttle position (TP) sensor electrical connector


b3a94a2.gif
TP sensor


To install:
  1. Install the screws and the TP sensor. Tighten screws to 7 inch lbs. (3 Nm)
  2. Connect the throttle position (TP) sensor electrical connector.
  3. Connect the battery ground cable.

Apr 25, 2010 | 2004 Ford Taurus

1 Answer

Grand cherokee 1998, 4.0 L, throttle position sensor.


check computer ground in black and blue wire

Apr 07, 2009 | 1989 Jeep Wrangler

1 Answer

Crankshaft position sensor


You will have to pull the harmonic balancer to change this,You can use A standard puller but you have to have specific bolts to go through the elongated holes and thread into the backplate.A snapon puller and a mack puller usually come with the correct bolts! Good luck

Mar 26, 2009 | 1998 Pontiac Bonneville

2 Answers

Check engine light is on and high idle (1500rpm)


Some times the E.G.R. will stick half open. This will make the engine surge or have high idle. Try replaceing the E.G.R. located under the upper intake. Do not go with after market E.G.R. The spring in them are to powrefil and the E.G.R. wil not open. Also try replaceing the O2 sensors. This could give the engine more fuel thus a higher idle. Some vehicles the T.P.S. can be ajusted, do some checking to see if yours is adjustable.

Please contact me if your problem presists.
Thanks, Charlie

Feb 03, 2009 | 2000 GMC Jimmy

1 Answer

Lossof power and ets off inicator on


check fuel pressure 1 fuel pump 2 fuel pressure regulator and 3 fuel filter.

Oct 30, 2008 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...