Question about 2001 Ford Crown Victoria

Open Question

I have a 2001 ford crown vic.That cranks but will not start,Fuel pressure is ok but has no spark.I replaced the crank sensor but still no spark.I checked for voltage at the crank sensor and there is none.Fuses and relays are ok and there are no codes

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: 1992 crown vic 4.6l

did you check the inertia switch?? that's what happened to mine

Posted on Aug 13, 2008

Ad
motor1258
  • 6674 Answers

SOURCE: 1997 ford explorer cuts off while driving down

If you confirmed spark is there, and you hear fuel pump working, I'd still try spraying WD-40 in throttle body intake for a couple of seconds, when it won't start, just to see if it kicks over, just in case pump is running but not up to pressure. If it fires for a second or 2 with WD-40, then you know lack of fuel is the problem.

Posted on Jun 11, 2009

  • 2 Answers

SOURCE: 89 ford probe, 2.2 turbo, no spark.

Check out your "fuel cut-off switch" located by the windshield washer tank behind the driver's side wheel-well panel in the trunk. It's a small box with a push-button at the top. If the button is "soft" when you push it, that's probably your problem. Replace the unit by removing the washer fluid tank first. The box simply plugs in. Probably about $ 100. I replaced three in my Probe. They rot out, and the car simple dies.

Posted on Nov 11, 2009

  • 104 Answers

SOURCE: 2003 CROWN VIC HAS NO

DID YOU CHECK THE FUEL PUMP SHUTOFF SAFETY SWITCH ON THE LH/DRIVERS SIDE IN THE TRUNK & MAKE SURE IT IS DOWN ,& EVEN IF IT IS SOMETIMES YOU CAN TAKE SOMETHING & PUSH IT UP & THEN PUSH IT BACK DOWN & IT WILL CRANK,& BELOW THAT SWITCH IN THE TRUNK IS A FUEL PUMP DRIVER MODULE ,IT MAY BE BAD,THOSE ARE A COUPLE OF THINGS THAT HAVE WORKED FOR ME ,& THATS PRETTY MUCH ALL I DO IS WORK ON FORDS, & LX CROWN VICS & P71 POLICE CROWN VICS WHERE I AM WORKING, HOPE THAT IT MIGHT HELP YOU FIX IT. SEAN

Posted on Dec 05, 2009

  • 1 Answer

SOURCE: Location of fuel pump relay on a 2001 Ford Crown Vic

where is the fuel pump relay on a 2001 crown vic p71

Posted on Apr 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 95 Ford crown Vic it will turn over but won't crank,it has half a tank of gas,changed the fuel relays,all fuses good in all fuse boxes but it will not start only turn over I'm lost


check codes first--may find problem there.
check spark on more then 1 cylinder.
check fuel pressure and volume--if fuel filter is stopped up, may have overworked fuel pump. With fuel cap off you should hear fuel pump running (key on) If not running, check for power at sub harness--Lastly tap on bottom of fuel tank with RUBBER hammer while someone else is cranking vehicle--if it starts get it to where you can remove tank before turning off--very often one time deal.

Jan 26, 2015 | 1995 Ford Crown Victoria

3 Answers

Crown vic 2005 no start replaced fuel pump


check your crankshaft position sensor. fuel+spark+compression+timing=ignition.

Mar 13, 2014 | Cars & Trucks

1 Answer

Engine cranks but will not start


Have a pressure test done on the fuel manifold to check for pump---pressure regulator and filter- The carbon on a plug indicates excess fuelling, either from bad injectors or over pressure.. Back firing in the exhaust is from unburnt fuel accumulating in the exhaust system and igniting . Misfiring is always thought to be plugs and leads but injectors and fuel pressure play an equal role in that area.

Feb 24, 2014 | 1999 Ford Crown Victoria

1 Answer

2001 ford crown vic cranks but wont start


Do you have spark and normal fuel pressure when cranking the engine ?

Jan 20, 2014 | Cars & Trucks

1 Answer

1999 ford crown vic won't start. changed fuel


Maybe your problem is with the one or many injectors, if just one is bad, you will have problems. Get yourself a multimeter and set it to read in ohms and find what spec the injectors should be at. If out of spec, then you need to replace that one injector(s).

Mar 25, 2013 | Cars & Trucks

Not finding what you are looking for?
2001 Ford Crown Victoria Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...