Question about Cars & Trucks

1 Answer

Coolant bleeder screw for 2006 chevy monte carlo

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 75,130 Answers

Duplicate question.

Posted on Nov 02, 2012

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2039 Answers

SOURCE: Jump starting a chevy monte carlo 1997

negative any metal part of engine wiggle the cable to have good contact that it cheers pierre

Posted on Jun 24, 2008

michigan man
  • 3533 Answers

SOURCE: 2006 monte carlo stuck in park

sometimes if the steering wheel is locked it won't come out of park try applying on the brakes and at the same time move the wheel back and forth and if this does not work and you have tilt it may be a problem in the steering column

Posted on Jan 21, 2009

Healeyman
  • 1198 Answers

SOURCE: i need a diagram for my 1980 chevy monte carlo

'80 Monte Carlo, a good ride. A Chilton's book is a good investment. It will show you wiring and vacuum hoses and how to do the brakes, etc.

Posted on May 03, 2009

ourhowse
  • 2007 Answers

SOURCE: belt diagram for a 2006 chevy monte carlo

There should be a decal on the bottom side of your hood, or somewhere in the engine compartment. If there isn't just put it on the crankshaft (bottom pulley) and go ribs to ribs, and flats to flats, and work your way around.

Posted on Jun 10, 2009

litoshop
  • 298 Answers

SOURCE: 2002 chevy monte carlo won't start

this vehicle is equipped with a factory anti theft system if when you try to start the engine and the anti theft light is on then the starter won't start even if your check engine light is not on you would have to scan the body module to pin point the problem to see if it's the anti theft system or the starter, go to a auto parts store like auto zone or pep boys or western auto these store offer free scanning to there customers. if this information has been helpful please let use know good luck

Posted on Jul 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does the heater in my 2005 chevy monte carlo only blow cold air?


Try this...I found it on the web.

The cooling system in these cars must be bled. That is all the air removed after the cooling system is serviced. Set the heating controls to full heat & open the bleeder screw, which is probably located at or near the thermostat housing until coolant flows smoothly out. Leave the screw open for an additional 10 seconds & you should be all set

Nov 11, 2014 | Cars & Trucks

1 Answer

2006 Chevy equinox ls 3.1 how do you bleed the radiator coolant system


If you look on the passenger front of the engine you should see a pipe coming up from the water pump housing. There should be a bleeder screw on the top. use a 9/32" socket to loosen the bleeder. Start the engine and keep bleeder open until coolant comes out. Close it and let the engine come up to temp while periodically opening the bleeder to let any additional air out. Keep an eye on the coolant level and top off as necessary.

Dec 15, 2012 | 2006 Chevrolet Equinox

1 Answer

I can't find the starter on my 2006 chevy monte carlo


if you are standing front of the car , look down at the radiator it is right there under the front front exhaust manifold

Dec 03, 2012 | 2000 Chevrolet Monte Carlo

1 Answer

Where is the coolant bleeder screw for 2006 monte carlo


It is located at the thermostat housing

Nov 02, 2012 | Cars & Trucks

1 Answer

Where does the coolant temp sensor go in the 2006 chevy monte carlo


It should be located just below the thermostat housing. Look on the engine where the top radiator hose mounts connects. From the front of the car, look towards the driver's side about two inches below the thermostat. You should see a wiring harness going from the sensor to the exhaust manifold.

Jul 27, 2011 | 2006 Chevrolet Monte Carlo

2 Answers

Where is ect sensor located on 2006 monte carlo 3.5 engine


The ECT (Engine Coolant Temp sensor) should be located by the coolant thermostat housing or where the upper radiator hose connects to the engine. It screws in with a plug or small/short wire harness attached to it. -------------------------------- To replace ect sensor:---
  1. Drain and recycle the engine coolant.
  2. Remove the intake manifold cover, if necessary.
  3. Remove the exhaust crossover.
  4. Disconnect the Engine Coolant Temperature (ECT) sensor electrical connector.
  5. Remove the ECT sensor.
see fig below:--- techmecho.jpg

.Thanks.

Jan 04, 2011 | 2006 Chevrolet Monte Carlo

1 Answer

After replacing the water pump how much coolant to water should i add


it will usally take 1-2 gallons of coolan. th best way to fill it up is by removing the bleader screw/s and filling the system cold. after coolant comes out of the bleeders put them back on and start the car till the t-stat is opened and double check the level once the engine has cooled down.

Nov 19, 2010 | 2004 Chevrolet Monte Carlo

1 Answer

How do I bleed the air out of the coolant on a 2000 Monte Carlo LS 3.4L?


Look for a bleeder screw at the highest point of the coolant system, it is usually located on the thermostat housing. Once located open screw with engine off and cool, and pour coolant into the coolant resevoir/ radiator until steady stream of coolant starts to come out of bleeder screw.

Nov 24, 2009 | Chevrolet Monte Carlo Cars & Trucks

1 Answer

Belt diagram for a 2006 chevy monte carlo


There should be a decal on the bottom side of your hood, or somewhere in the engine compartment. If there isn't just put it on the crankshaft (bottom pulley) and go ribs to ribs, and flats to flats, and work your way around.

Jun 10, 2009 | 2006 Chevrolet Monte Carlo

1 Answer

Ac coolant


R-134A is the proper refrigerant for your car. Hope this answers your question. Best of luck.
Greg

Jun 01, 2009 | 1996 Chevrolet Monte Carlo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...