Question about Chevrolet Cars & Trucks

Open Question

How to reset your oil change light for a 2008 chevy trailblazer

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

chuck943
  • 783 Answers

SOURCE: Need to reset the oil change indicator, changed oil myself

press and release the setup button to display oil life= xxx
then press and hold the reset button for about 2 sec it should then display oil life set to 100%

Posted on Jan 30, 2009

  • 1 Answer

SOURCE: my oil light with a little wrench beside it came on

If the service light is on in your TrailBlazer, open the door, turn the key to ignition position and push the accelerator pedal 5 times, the service light will flash. flash your high beams and you're done.

Posted on May 13, 2009

  • 2 Answers

SOURCE: How do I get the "Change Oil " light to go off after change .

Turn key to the run posistion and pump the gas peadle 3 times under 5 seconds.

Posted on Jul 18, 2009

greg_margo
  • 1959 Answers

SOURCE: how to reset oil light after oil change on 2005 trailblazer

  1. Turn the key to the "ON" position
  2. Press the accelerator all the way to the floor 3 times within 5 seconds
  3. You should see the oil light flash, once it stops flashing, turn the key off
  4. Wait 10 seconds before starting the vehicle, the oil light should now be reset
  5. If this doesn't reset the light, repeat steps 1-4 paying careful attention to pressing accelerator all the way to the floor 3 times within 5 seconds
Best of luck.
Greg

Posted on Aug 10, 2009

techbuster
  • 5081 Answers

SOURCE: Reset oil change for a 2008 dodge aveneger

To reset your maintenance reminder system (even if the light hasn’t come on yet), you’ll need to turn your key to on (but don’t start!) and make sure your odometer is on TRIP A. Then key off. Press and hold the Odometer/Trip button. While holding down on the button, key the ignition to on (Don’t start the engine!) The display panel will count down from “------“ to “-“Continue pressing the button until the Trip A is displayed. After this step, you are done.

Posted on Oct 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to reset oil warning light on a chevy trailblazer ls 2006


The way to reset the oil light on your Trailblazer is.You first turn the key on but do not start the vehicle.Press the gas pedal 3 times all the way to the floor within 5 seconds.The change oil light will flash several time then go out.The oil life has been reset.Remember don`t start the vehicle just key on engine off.Hope this helps.Good luck.

Dec 09, 2011 | 2006 Chevrolet Trailblazer

1 Answer

2006 chevy trail inline 6. Change engine oil light came on all of sudden. I changed the oil just 2000 miles ago. What does it mean? How do I reset ?


{: ) It could be that it was not reset properly and successfully when you last changed your oil. A scan tool can reset it better. Also, double check for oil level and leaks.

May 29, 2011 | 2006 Chevrolet Trailblazer

1 Answer

How many quarts of oil does a 2008 chevy trail bl...


with new filter it takes 7 quarts. that is assuming you do not have an ss trailblazer or v8 model

May 20, 2010 | 2008 Chevrolet Trailblazer

1 Answer

How do I reset my oil light on a 2005 Chevy


Turn the ignition to the "ON" position without starting the vehicle. Press the gas pedal in 3 times, holding it in for 2 seconds each time. When the "Change Oil" light flashes, start the vehicle.

Feb 11, 2010 | 2005 Chevrolet TrailBlazer

1 Answer

I have a 2008 Chevy Impala and I just had an oil change done about 3 weeks ago. Just recently the warning light turned on saying "please change oil engine soon? I checked the oil and it is still full with...


YOU HAVE TO RESET OIL LIGHT.ITS DISPLAYED ON THE DRIVER SIDE INFORMATION CENTER.IT A CHECK MARK LOOKING SYMBOL..YOU PRESS HOLD RESET BUTTON FOR 5 SECONDS.

Jan 23, 2010 | 2008 Chevrolet Impala

3 Answers

My oil light with a little wrench beside it came on this morning, I have a 2007 chevy trailblazer and I just had a oil change 1 month ago


If the service light is on in your TrailBlazer, open the door, turn the key to ignition position and push the accelerator pedal 5 times, the service light will flash. flash your high beams and you're done.

May 06, 2009 | 2007 Chevrolet TrailBlazer SS

1 Answer

How do I reset the oil change light in a 2008 Chevy Suburban


Try this: turn the key to the RUN position (don't start it), press the accelerator to the floor 3 times within 5 seconds. The oil life light should flash twice, indicating that it's been reset.

If you have steering wheel controls, you can navigate to where it says Oil Life and then hold the arrow down, that should also reset the oil life.

Mar 30, 2009 | 2008 Chevrolet Suburban

3 Answers

Reset button to push after changing oil


turn key on in the run position press gas peddle to the floor 3 times with in 5 seconds the wait ten 10 seconds i do these all the time

Feb 13, 2009 | 2005 Chevrolet Trailblazer Ext

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...