Question about Peugeot Cars & Trucks

Open Question

How to remove heater blower motor from peugeot 806

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1861 Answers

SOURCE: Heater Blower Motor

Remove the glovebox door, and the under dash cover/trim panel.

Look behind where the glove box was, you will see the heater box

At the bottom of this box, there is a round plate with a wiring connector and 3 screws holding this plate to the heater box.

This plate is the bottom of the heater fan assembly; remove the connector, and the 3 screws. The fan motor will drop staright down. Real easy to do.

Posted on Oct 21, 2008

Ad
johnny5846
  • 379 Answers

SOURCE: How to remove a blower motor

1.) remove screw from right door sill trim plate, (that piece of trim that covers the edge of the carpet when the door is open) 2.) remove right hinge pillar trim panel (passenger side kick panel) 3.) disconnect blower motor electrical connectors 4.) remove blower motor cover 5.) disconnect the cooling tube (rubber hose that attaches to the motor ) .6.) loosen courtesy light screws and move light out of way (if equipped) 7.)remove right side dash support bolt (under dash twist your head around like the excorsist, , lol , where the dash meets the side panel pillar) 8.)remove blower motor-to-case screws 9.) remove blower 10.) remove fan from blower motor shaft 11.) to install reverse removal procedure ,.. not as bad as it sounds , cheers.

Posted on Jan 10, 2009

  • 318 Answers

SOURCE: 2003 corolla how to remove test heater blower

Why not check it in the car? It is under the glove box.

Posted on Jul 13, 2009

  • 14036 Answers

SOURCE: How can I change the gearbox oil on a peugeot 806

MOST MANUAL TRANSMISSION BEFORE CHANGING FLUID YOU DRIVE CAR AROUND.TO WARM THE OIL.SO IT WILL DRAIN OUT EASILY.NOW SAFELY RAISE VECHICLE AND SUPPORT IT ON JACK STANDS.LOCATE DRAIN PLUG ON DIFFERENTIAL PORTION OF THE CASE.GET SOME RAGS ON HAND.AND A DRAIN PAN.PLACE THE DRAIN PAN UNDER TRANSMISSION. REMOVE THE DRAIN PLUG.LET THE OIL DRAIN.WHEN FINISH.PUT IN NEW GEARBOX OIL.

Posted on Sep 06, 2009

Testimonial: "prompt, concise and clear explanation. I was pleasently surprised"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the heater/blower resistor on a Peugeot 308


Those resistors are located with the blower motor.

Jan 28, 2017 | Peugeot 308 Cars & Trucks

1 Answer

How do i change the heater matrix on a peugeot 806


Clamp the hoses to the matrix or drain the coolant but you will still get a bit off leakage when you disconnect the hoses in the footwell
remove the glovebox door and the panel below and you can then see the blower housing

Jan 10, 2017 | Peugeot Cars & Trucks

1 Answer

Timing on 1.9 diesel 806


There is no mark there is a hole in the block behind the starter motor which you have to insert a pin which locates into the flywheel to lock the crank into place you might find it easier to remove the starter motor

Nov 14, 2013 | 1987 Peugeot Liberte

1 Answer

Heater resistor on 806


The blower motor resistor is located right next to the blower motor under the dash.

Oct 31, 2012 | Peugeot Cars & Trucks

1 Answer

My heater blower has stoped working on my peageot


There is a 4" long Green ceramic resistor by the blower motor, prone to fail, I think Valeo does them on the aftermarket.

Nov 19, 2009 | 2005 Peugeot 405

1 Answer

How can I change the gearbox oil on a peugeot 806 manual vehicle the reg is 1996 I have had to put in a different model and year on the form as my car is not available as an option. My car is definatley a...


MOST MANUAL TRANSMISSION BEFORE CHANGING FLUID YOU DRIVE CAR AROUND.TO WARM THE OIL.SO IT WILL DRAIN OUT EASILY.NOW SAFELY RAISE VECHICLE AND SUPPORT IT ON JACK STANDS.LOCATE DRAIN PLUG ON DIFFERENTIAL PORTION OF THE CASE.GET SOME RAGS ON HAND.AND A DRAIN PAN.PLACE THE DRAIN PAN UNDER TRANSMISSION. REMOVE THE DRAIN PLUG.LET THE OIL DRAIN.WHEN FINISH.PUT IN NEW GEARBOX OIL.

Sep 06, 2009 | 1991 Peugeot 505

1 Answer

Location of horn (s), Peugeot 806 2.0 HDi (2001)


in the corner of the bumper, i think n/s remove in **** shield or undo from bumper and pull back

Apr 09, 2009 | 2005 Peugeot 405

1 Answer

No power supply to the heater fan switch


not sure if its a green 30amp fuse in the glove compartment / under dashboard foot well. / under the hood maybe. i think they only use one fuse for the blower motor.

Jan 17, 2009 | 2006 Peugeot 604

1 Answer

Peugeot 306 blower not working


have a look at the wiring to the reostat and heater motor they are known to burn out at the plug connectors. also mebe sure the motor has not siezed

Jan 11, 2009 | Ford Escort Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

371 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

mike hayward

Level 2 Expert

279 Answers

lloyd cole

Level 2 Expert

250 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...