Question about Cars & Trucks

Open Question

How to bleed cooling system on a jeep liberty

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 14036 Answers

SOURCE: How do i bleed the cooling system of a 1987 jeep

TO BLEED COOLANT SYSTEM.ALL YOU HAVE TO DO IS FILL RADIATOR WITH COOLANT UNTIL ITS JUST BELOW THE CAP.CRANK CAR UP LET ENGINE IDLE UNTIL IT WARM UP UNTIL THERMOSTAT OPEN UP.ADD COOLANT UNTIL COOLANT LEVEL STOP DROPPING WHEN COOLANT STOP DROPPING YOUR COOLANT LEVEL IS CORRECT AIR BLEED OUT.BECAREFUL DONT GET SCALDED.WHEN ENGINE GETS HOT WAIT UNTIL IT COOLS BEFORE REMOVING RADIATOR CAP.USE A LARGE RAG OVER RADIATOR CAP OPEN CAP A LITTLE AT A TIME THIS WAY YOU WONT GET SCALD.

Posted on May 25, 2010

Ad
  • 57 Answers

SOURCE: bleeding brakes on 2005 jeep liberty

you will have too take brake lines off by the master cyclinder by the brakes and have some one pump the brake pedal in and out catching the fluid in a gug and keep pooring fluid in fill container till all aire is out of lines

Posted on Jul 12, 2010

  • 6982 Answers

SOURCE: how do i bleed the

All you need to do on those is on level ground, run it with the heater on high heat with the radiator cap open. Fill as necessary 'till no more can be added, close it up and add vcoolant to the full line on the overflow tank.
If you are consistently encountering an overheat and finding air in the system you may have a head gasket or cracked cylinder head that is permitting combustion gasses in there. (a hydrocarbon test at the radiator will tell you that).
If you are having any other problem there, ask and I'll try to help.

Posted on Nov 22, 2010

clifford224
  • 1975 Answers

SOURCE: 2002 jeep liberty sport wiring

Here's the information you needed. I hope this helps and good luck.


clifford224_318.jpg

clifford224_319.jpg
clifford224_320.jpg

Posted on Aug 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the position of radiator fan relay on jeep liberty 2006


no idea to be honest earlier jeeps had then at the front of the wing down below as i remember ?? newer one would i imagine be in the electrical box under the bonnet near the battery

Dec 02, 2016 | Jeep Cars & Trucks

2 Answers

Where is the location of the slave cylinder in a Jeep Liberty 2005


Near the engine on the transmission side of the connection.

Jan 16, 2015 | 2005 Jeep Liberty

1 Answer

Need cooling system diagram for 2010 jeep liberty 3.7 v6


It is electric.It is mounted in the center on top off the air plenum. You have to remove the dash to get to it. Last one I did was the heater core. 2003, had to remove the dash out of the vehicle, drop the steering column and remove the air plenum. All day job. You need a manual, lots of nuts, bolts, and screws to remove.

Dec 28, 2014 | 2010 Jeep Liberty

2 Answers

Bleeding air out of a 2003 jeep liberty sport with a 3.7 motor


Let it cycle the therm state a few times w motor running and cap off....there is a bleeder valve on the upper hose above the serpentine belt..make sure to take that out to relieve any air stuck in hose/pipe

Sep 15, 2014 | 2003 Jeep Liberty

1 Answer

Heat varies on 2002 Jeep Liberty


The most common fault is air pockets in the cooling system.
Is the radiator full of liquid coolant ?

Feb 14, 2014 | Jeep Liberty Cars & Trucks

2 Answers

Heater not blowing hot air


it appears that you have an air lock in the coolant system. bleed out the air by loosing of the highest hose until only water comes out or have the system pressure bled at a radiator shop.

Jan 25, 2014 | Jeep Liberty Cars & Trucks

1 Answer

Installing a master cylinder on a 2005 jeep liberty sport


Remove it, bench bleed the new one, install it and bleed lines. More simple it can't be!!

Sep 27, 2009 | 2005 Jeep Liberty

1 Answer

My jeep just starting to run hot and i want to try to change the thermostat but i don't see it. I follow the hose but it runs under the air cond and the alternator, how do i get to it. thank You


the thermostat on this vehicle is located on the lower rad hose at the engine end of hose..small plastic housing with 2 bolts..make sure you remove coolant bleed plug at top of engine before you refill system..make sure cooling fan is working properly also

May 10, 2009 | 2003 Jeep Liberty

1 Answer

Troubled brakes


TAKE IT TO THE DEALER, SINCE VEHICLE HAS ABS SYSTEM . THE BRAKES MAY NEED TO BE BLEED WITH DRB/SCANNER. OR YOU MAY HAVE LINES CLOGGED.

Dec 30, 2008 | 2005 Jeep Liberty

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,239 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...