Question about GMC Cars & Trucks

Open Question

How do you remove intake manifold 3.5 gmc canyon

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2039 Answers

SOURCE: 2007 GMC Canyon

they have so many electrical component there nothing wrong with it manly all car today that dont run daily do that park a mercedes for 2 weeks the same will hapen bmw ect charge our battery and drive it thanks for using fixya pierre

Posted on Jun 23, 2008

psds4
  • 293 Answers

SOURCE: 1998 chevy tahoe 5.7 intake manifold removal

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528008effd
this should help

Posted on Oct 23, 2008

  • 1 Answer

SOURCE: Remove radio/cd from 2004 GMC Canyon

Check out Crutchfield.com. They have detailed instructions on how-to install radios in your Canyon.

Posted on Jan 03, 2009

  • 17 Answers

SOURCE: intake manifold cover

remove oil cap steam an it should just lift off

Posted on Feb 23, 2009

michigan man
  • 3533 Answers

SOURCE: How do i remove the intake manifold to reach back

give these websites a try www.alldatadiy.com and www.autozone.com if all fails stop by your local library and get your hands on a Haynes auto repair manual for your car wish you the best of luck Michigan Man.

Posted on Jan 25, 2010

Testimonial: "HONESTLY,I'VE BEEN SEARCHING FOR HOURS FOR A SOLUTION TO MY HEAD ACHE. YOUR ANSWER WASN'T AS DIRECT AS I WAS HOPING, BUT GOOD SO FAR. THANKX! "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace MAP sensor for 2004 gmc canyon


manifold absolute pressure /v8 remove intake cover.disconnect map.detach retaining clips /easy /its the same on v6 but u have intake aiair duct and resonator.its connected to the side i would give u a pic but its cold here

Jan 23, 2013 | 2004 GMC Canyon

1 Answer

Location to change camshaft sensor for a 2005 gmc canyon


4 cyl or V6 engine ?
I think the 4 cyl is on the side of the block under the manifold.

Sep 22, 2012 | 2005 GMC Canyon

1 Answer

How to change a fuel rail on a 2005 canyon in line 5


In a nutshell... Take the intake manifold off and then you can access the fuel rail for removal.

Aug 30, 2012 | 2005 GMC Canyon

1 Answer

Where is the egr valve located on a 2005 gmc canyon truck


The 5 cyl engine looks like it is mounted on top of the exhaust manifold.

Aug 16, 2012 | 2005 GMC Canyon

1 Answer

I HAVE ANTIFREEZE LEAKING OUT OF MY INTAKE MANIFOLD ON MY 1987 GMC JIMMY


I had this happen to me the first time I replaced my intake manifold gaskets. It was hard to install the intake and gasket moved just enough and I had a coolant leak. Removed manifold and installed new gaskets and problem was solved. Good Luck.

Jul 26, 2011 | 1987 GMC Jimmy

1 Answer

How to replace an intake manifold gasket on a 1996 gmc jimmy


Hello,

Here is a detailed summary on the procedure of how to replace the intake manifold gasket on a 1996 gmc jimmy;
REMOVING THE UPPER INTAKE MANIFOLD(PLENUM)
STEP 1 Disconnect Battery (may not be absolutely necessary, but a good practice to avoid shorting a positive wire to ground).


STEP 2 Remove serpentine belt.

STEP 3 Drain the coolant.

STEP 4 Remove air cleaner ducting and disconnect wires.

STEP 5 Disconnect throttle linkage and bracket.

STEP 6 Disconnect cruise control cable.

STEP 7 Remove brake booster vacuum hose at manifold.

STEP 8 Remove PCV hose.

STEP 9 Remove ignition coil and bracket.

STEP 1O Remove purge solenoid and bracket.

STEP 11 Relieve fuel pressure at test port.

STEP 12 Remove fuel lines and bracket.

STEP 13 Remove upper intake manifold.

REMOVING THE LOWER INTAKE MANIFOLD
STEP 1 Remove the distributor and label the spark plug wires.

STEP 2 Remove heater hoses and bypass hose.

STEP 3 Remove upper radiator hose.


STEP 4 Remove EGR valve?

STEP 5 Remove sensors and bracket on right side.

STEP 6 Remove EGR tube, clamp and bolt.

STEP 7 Remove PCV valve (and replace).

STEP 8 Unbolt A/C compressor and move it aside.

STEP 9 Loosen compressor bracket and slide forward, but do not remove it.

STEP 10 Remove alternator bracket bolt (or remove alternator and set aside)

STEP 11 Unplug all vacuum lines from intake manifold.


STEP 12 Unplug all electrical connectors from manifold.

STEP 13 Take note of the intake manifold bolts and mark the location of the bolts.


STEP 14 Remove intake manifold bolts, and manifold.

STEP 15 Clean mating surfaces

THE MAIN INSTALLATION
STEP1 Set the new gaskets in place and apply silicone to flat areas on front and rear of engine block.

STEP2 Apply thread locking compound to manifold bolts.

STEP 3 Install the manifold and tighten bolts to 35 ft-lbs, in proper sequence.

STEP4 Install the distributor.

STEP5 Install the upper intake manifold.



The remaining installation procedures are basically the reverse of removal.


Have a nice day.

Dec 04, 2010 | 1996 GMC Jimmy

1 Answer

Hot do you take off a 98 GMC 5.7 vortec intake


Note, removing the upper intake manifold is not necessary when removing lower intake manifold, they are removed as an assembly.
Disconnect negative battery cable. Drain cooling system. Remove air cleaner assembly and inlet duct. Mark and remove distributor. Remove upper radiator hose at thermostat housing. Disconnect accelerator and cruise control cables. Remove heater hoses from intake manifold. Remove EGR pipe.
Disconnect fuel lines at rear of engine. Remove AC compressor and set aside(leave hoses connected). Remove canister purge solenoid. Disconnect theSCPI injector, ignition coil, Ignition Control Module, generator,IAC motor, TP sensor, O2 sensor, Exhaust Gas Recirculation valve and Engine Coolant Temperature sensor wiring harness connectors. Remove PCV valve and hose. Remove lower intake manifold bolts. Remove lower intake manifold.
Installation.
Always use New O-rings when reconnecting fuel lines at rear of engine. Apply a bead of RTV silicone sealer along the front and rear sealing surfaces of the block.See Fig.6. Install new gaskets and intake manifold on block while RTV is still wet to the touch. Use Threadlock 12345382 or equivalent to lower intake manifold bolts. Tighten lower intake manifold bolts in sequence to specification table. See fig. 7. To complete installation, reverse removal procedure.f52665d.gifabc2b5f.gif

Oct 10, 2009 | 1998 GMC Sierra

1 Answer

2006 gmc canyon 3.5 inline 5 cyl.


Not much of a vacuum diagram on this vehicle. Uses vacuum mainly for the EVAP system ( not a good source). Best bet would be to use a source that stems directly from the intake manifold. Good luck

Jul 07, 2008 | 2006 GMC Canyon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...