Question about Cars & Trucks

Open Question

How to replace thermostat in 1998 isuzu rodeo

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2000 isuzu rodeo V6 3.2l thermostat replacement

Well, as you said, Isuzu engineers are not the brightest. We are in the process of trying to figure out how the oil got full of water! If anyone has experience in the 3.2 V6 2000 model and where the likely failed spot for the cooling system is, I'm all ears.
To your problem, the thermostat housing is located under the intake manifold, yes under it. You will have to remove the intake and fuel injection system (lots of fun) to get at the hard pipe lines under and in the front of the engine. Once there removal and replacement of the thermostat is easy.

Posted on Jan 27, 2009

Ad
  • 4 Answers

SOURCE: timing settings for a 1998 isuzu rodeo

You didn't say whether you had a V6 engine or a 4cyl. Here is the procedure for a V6.

It sounds like he moved the cam shaft independently of the crankshaft or other camshaft so you will need to do all these procedures:

1. Turn the crankshaft until the mark on the spocket is lined up with the mark on the oil pump housing (the mark is on the driver's side at 90 degrees to the sprocket itself).

2. Back off the crankshaft counterclockwise 1/8 turn to ensure the pistons aren't at top dead center. This gives the valves room to move without hitting the piston.

3. Turn the passenger's side camshaft until it "jumps" into place with the alignment mark on the camshaft pully is pretty close to being lined up with the mark on the engine head.

4. Turn the driver's side camshaft until it "jumps" into place but this won't be perfectly lined up with the mark but will be about an 1/8 turn off from the mark. Then line it up by hand.

5. The idler pulleys and tensioner pulleys should be installed on the engine but the tenioner pulley adjuster (it is a little cylinder with a rod coming out of it that is held in place by 2 bolts) should be removed.

6. Place the new belt on the crankshaft first. Be sure the arrows on the belt point in a clockwise direction. If you have a belt with lines and dots then the lines will line up with all markings that you have lined up together. The dots should line up at the 270 degree point on the crankshaft (opposite of the lines and the markings).

7. Loop the belt around the tensioner pulley, around the passenger's side cam, under the waterpump, around the driver's side cam, and finally around the idler pulley. Check all alignments.

8. Put the tesioner adjuster in a vise and squeeze it together until you can place a small drill bit or allen wrench through the holes to keep it compressed.

9. This is the tricky part. You will need to install the tensioner adjuster and that will require some moving of the belt to allow enough play to get the adjuster in place. This may move the passenger's side alignment. If so, you will need to try it again. I find that if you move passenger's side alignment mark clockwise by one tooth of the sprocket, then when you go to put the tensioner in place it lines up. You may find other tricks to overcome this challenge.

10. Once you think you have everything lined up. Use a wrench to turn the crankshaft sprocket 2 full turns. Listen closely and feel for any hard resistance as you do this to determine if the pistons are hitting the valves. If you believe they are hitting each other thenrepeat the adjustment procedure. Not doing this can ruin the valves or more.

11. If everything seems OK. remove the drill bit or allen wrench from the tension adjuster. Perform step 10 again for one final check.

I hope this helps.

Posted on Feb 22, 2009

  • 15 Answers

SOURCE: 1998 isuzu rodeo thermostat location

0eafb73.gif
Hope this will help...

Posted on May 07, 2009

  • 22 Answers

SOURCE: replacing the power steering pump on a 1998 isuzu rodeo

Remove low pressure and high pressure hoses (this one could be hard to break loose). You might want to have an oil pan handy, to capture the oil. Disconnect electrical sensor. Remove the bolt that holds belt tension adjustment plate. And finally remove the bolt that holds the pump in place. It is bolted from the back and located at the right lower corner of the pump if you are facing the front of the car. Remove the pump assy. I could not remove belt pulley at home, no matter how hard I tried. Ended up taking it to an automotive shop and they removed it in no time, using one of those "pneumatic impact guns". Assemble new pump. Fill the reservoir with PS oil. Make sure both of the front wheels are off the ground, start the engine and slowly spin the steering wheel back and forth for about 5 minutes or untill screeching sound stops and the liquid in the reservoir stops foaming. That will bleed any air that is in the system. Don't go all the way to the end of stroke. Good luck.

Posted on May 09, 2009

honeymokey
  • 3113 Answers

SOURCE: water pump replacement 96 isuzu rodeo

Remove belt, fan, fan shroud and fan bracket. Remove timing covers, timing belt and water pump. Replace timing belt and the hydraulic tensioner with new ones. I suggest you get a mechanic to do this as you can easly get it out of time. Not an easy job.

Posted on Jul 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does the starter relay fuse for a 1998 Isuzu rodeo look like and where is is located in the fuse box


Crystal, this is what I found on the Rodeo starter fuse/relay.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
99 Isuzu Rodeo LS Underhood Fuse Box Diagram Circuit Wiring Diagrams
1997 Isuzu Rodeo Question Fuse Box Diagram Electrical Problem
1999 Isuzu Rodeo Main Fuse Box Diagram Circuit Wiring Diagrams
1998 Trooper Relay Solenoid Starter 1998 Isuzu Trooper All of

Jul 06, 2016 | Isuzu Cars & Trucks

1 Answer

COST OF STARTER REPLACEMENT ON ISUZU RODEO 1998


costs vary by a zillion factors.
country
city.
shop
taxes, rent, labor costs, insurance.
and if the parts are rusty. or related parts are destroy'd.
and if old parts have core value.
why ask here, we know NONE of this,
ask your mech. ask them, in your town.

Jul 14, 2014 | 2003 Isuzu Rodeo

1 Answer

How do you change the thermostat in a 1998 Rodeo


Follow the upper Radiator hose from the radiator back to the motor. remove the hose on the motor end and then remove that coupling that it was attached to. The thermostat is under that coupling. Remove the old seal and any remnants of that seal, put the new thermostat in place, put the new seal in place and bolt the coupling back down and reattach the hose, top off the radiator and test drive.

Feb 23, 2011 | 1998 Isuzu Rodeo

1 Answer

Where is thermostat located ,top right of motor behind where hose from rad connects?just had rad replaced but no flow through rad hope its t stat?


Check the nest graphic...

e615fe3.jpg

Fig. Exploded view of the thermostat housing (1), thermostat (2) and outlet pipe (3)

Hope help with this (remember rated this post).

May 19, 2010 | 1998 Isuzu Rodeo

1 Answer

Where is the thermostat located on a 1998 isuzu rodeo 3.2L


Hello joshmalik81: My name is Roger and I will help you. First drain down the coolant in the radiator. Next follow the upper radiator hose back to the top of the engine. You will find it connects to a metal tube held down by four bolts. Remove the four bolts and lift up the tube. You will find the thermostat under this metal tube.
Should you need further help please just ask. Please rate the answer. This way I know it was helpful. Thank You for using Fix Ya. Roger

Dec 12, 2009 | 1998 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...