Question about Chrysler Cars & Trucks

Open Question

I HAVE CODE PO 571 IT LED ME TO THE BRAKE LIGHT SWITCH AND REPLACED PROBLEM WENT AWAY FOR 3 WEEKS AND HAVE THE SAME PROBLEM AGAIN REPLACED THE SWITCH AGAIN AND STILL HAVE THE SAME PROBLEM

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 16 Answers

SOURCE: 1998 Plymouth Breeze

change your sparkplug wires that will salve yor problem

Posted on Dec 11, 2008

Ad
  • 1 Answer

SOURCE: brake lights blows fuse right away

I had the smae problem, i replaced the tail light circuit board and the problem was solved.

Posted on Mar 16, 2009

  • 42 Answers

SOURCE: 2000 s10 Blazer dies very 3-6 weeks for no reason

i would check your ignition system. you would need a meter for this but look for broke or loose connections. if it was a fuel problem i dont think it would just start up after 20 minutes. or you might try your ignition switch. if its shorting or something then ya well it would cut your engine off real quick

Posted on Mar 20, 2009

cadman000
  • 607 Answers

SOURCE: 1999 cadillac deville brake light switch

Replace the brake light switch - sticking . Hope this helps

Posted on Apr 23, 2009

emissionwiz
  • 76846 Answers

SOURCE: Check Engine Light comes on and off w/ P0304 code

this may be a defective fuel injector or a defective PCM (powertrain control module).

Posted on May 30, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 jeep grand cherokee overland code po871 tranny problem


code p 0871 refers to transmission fluid pressure (TFP) sensor C ---range /performance problem ==== causes --wiring ---poor connections ---TFP sensor ---ECM---TCM
code p 0841 refers to TFP sensor A same problems and same causes
if the connections are clean and tight and the wiring is in good condition , you change out both sensors and check the transmission control module (TCM) for operation

Aug 29, 2017 | Jeep Cars & Trucks

2 Answers

Po 171, po 305, po 441


Hi, I know from my past experiances the spark plug wires at the boot ends than slide onto the sparkplugs usually over time short out due to the metal tubes that protect the sparkplugs from heat kind of ark across from the metal tube through the plug boot causing an error code. Sometimes in the dark you can actually see them arking at the tube on the engine, and also hear a crackling noise. As to the code for the O2 sensor that's a normal wear and tear item that may need replaced. As all vehicle age over time electrical connections, and things have issues develop and cause havick with sensors and computers in these vehicles too.


As with the 441 code and then the other code for the O2 sensor showing up may mean both O2 sensors are going bad if your system has 2 sensors in the exhaust, usually one before the cat converter and one behind it. A lot of this also is due to what gasoline you use in the vehicle over time. Lower octane gas may be what is causing things to act up.

Jan 03, 2014 | Dodge Ram 1500 Cars & Trucks

1 Answer

Code 571


The code is not complete it should be P0571
P0571 KIA - Brake Switch A Circuit
Symptoms - Engine Light ON (or Service Engine Soon Warning Light)
- Stop light inoperative
- Cruise control system inoperative Possible causes - Misadjusted brake switch
- Brake switch open or short circuit
- Poor brake switch electrical connection
- Failed brake switch

Jan 27, 2012 | 2006 Kia Sorento

1 Answer

I have a problem with my 93 Bronco, I installed new LED bulbs, brake/tail/turn lights with the right size, now my brake lights stay on really faint and they light up bright when I step on brake pedal. The...


The LED- Light emitting diodes- use very little current and voltage to light up and so when you changed from the normal incandescent type +12 , these require only a fraction of the votlage. NOW what seems to HAPPEN is that the return voltage from the switch has RESIDUAL voltage which makes the LED light up, this can be a fraction of a volt and can be a LEAK from the switches, park, brake or otherwise.
Check the wiring once again , check the ground once again and isolate the switches to confirm the LEAK. You can also use a resistor to reduce the voltage if needed which can cut off the light when switch is off.

Oct 17, 2011 | Cars & Trucks

1 Answer

The light came on after I drove about 5 miles. Went off after a few more. Came on the next day after 3 miles and stayed on all the way to my destination. 2000 taurus 3.0 6 cyl running fine. PO 723 gear 4...


It sounds to me that your 4th gear is just starting to slip. It will gradually get worse until you are forced to overhaul the transmission.

My recommendations:

Clear the codes and drive the vehicle while at the same time, putting some money away so you will have the funds for an overhaul. It may do like this for a few weeks or several months, but it is well on its way,,,

Jul 10, 2011 | Ford Taurus Cars & Trucks

1 Answer

6 months ago, replaced head gaskets. 1 week later, service engine soon light came on. Tech said it was an oxygen sensor. Cleared code. 3 weeks ago, got oil change, replaced headlights and replaced...


CHECK TURN SIGNAL FUSE.IT COULD BE BLOWED OR YOU HAVE FAULTY TURN SIGNAL SWITCH.BECAUSE BACK LIGHTS AND TAIL LIGHTS SHARE SAME CIRCUIT WITH TURN SIGNAL SWITCH.

Jun 26, 2011 | 1999 Chevrolet Venture

1 Answer

I have a 1996 mitsubshi galant with a 2.4 motor check engine light comes on the code is 505 the car idles up and down at stop lights etc I did clean throttle body the problem went away after 3 weeks it is...


Bad idle air control valve. Most likely needs to be replaced. I'm guessing you have around 125K miles on your Galant, right? See other posts for solution.

Jun 24, 2010 | 1998 Mitsubishi Galant

1 Answer

I took my Camry 2000 (V6) to Sears for brake and power steering fluid flush. My brake light went on after the maintenance. Took it back the next day. They said my hand brake was not totally down. I did not...


if sears adjusted the brakes then the emergency brake handle can come on sometimes this has to be adjusted also ( always be careful when haveing anything power flushed as this can easely pop a seal and start leaking a few weeks down the line

Mar 03, 2010 | 1997 Toyota Camry

3 Answers

Tail lights and brake lights not working - not fuse - what can it be?


Brake light switch, located on upper brake pedal should be checked, that is most likely your brake light issue, but U say tail lights aren't working, but running lights do, tail lights and running lights I would consider to be the same, so can u clarify that for me? Let me know how the u do w/ brake light switch, and if u have issue w/ tail lights?

Nov 01, 2008 | 1994 Ford Thunderbird

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8560 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...