Question about Chevrolet Cars & Trucks
Posted by Anonymous on
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
the dealer will have to do it its a program in the car computer that is set up to monitor tire pressure since you changed the pressure the computer knows the change and is letting you know there is a possible leak.you can have it altered at the dealer only.
Posted on Feb 02, 2010
Not sure about your vehicle , but most chevys have a reset button in the fuse panel. It hase multiple functions , so you will have to check the owners manual or ask a chevy dealer the exact procedure. If memory serves me correctly , you push and hold the reset till the light flashes , then release and press it again. good luck
Posted on Mar 12, 2010
Well first you can please follow the below steps -
1. Make sure the ignition key is in the off position and the headlight switch is off. Release the hood latch.
2. Open the hood and locate the top of the headlight assembly where you intend to change the headlight. If a plastic shroud is present, locate the center bolt and remove it with a ratchet and a socket. Lift the shroud out of the way to access the headlight assembly retaining brackets. Some later models may feature a snap-release shroud requiring no tools to remove.
3. Locate the brackets on the top rear of each side of the headlight assembly. Lift them all the way up to align the hole on the bottom of each bracket to the retaining tabs on the assembly.
4. Pull the assembly forward away from the Malibu, but be careful not to scratch the bumper. There are three guide pins that require unseating. The guide pins are what aim the headlights and it may take some wiggling to get the pins from their seats.
5. Support the assembly with one hand and then reach behind the unit with the other. The low beam bulb is on the outside, the high beam bulb is on the inside. You can also replace the parking light if desired. Locate the wire harness connection. Un-clip the wire harness from the back of the bulb socket. Remove the bulb by turning it counterclockwise 1/3 of a turn to align the release tabs of the ring and the assembly. Wiggle the bulb out of the assembly.
6. Place the latex gloves on your hands before opening the package of the replacement bulb. Oil in our skin can damage the glass bulbs of halogen headlights.
7. Carefully insert the new bulb into the ring and then align the tabs of the ring to the tabs of the headlight assembly. Push inward and then twist clockwise 1/3 of a turn to lock the bulb in place. Reattach the wire harness. Rest the headlight assembly inside its cavity and test the operation of the headlight before securing the headlight assembly in place. Be sure to turn the lights and ignition back off.
8. Align the three guide pins to their seats and push the assembly back into them gently until they snap into place. Replace the retaining brackets by pushing them downward to lock into place. Replace shroud, if applicable. Remove the tools and old bulb and close the hood. Post comments for further help or information......
Posted on Mar 27, 2010
SOURCE: My service tire monitor light
This means you need to check the pressure in your tires. One or more is below the recomended limit. Fill it up and drive for a mile. Light should go out.
Posted on Sep 25, 2010
Tips for a great answer:
Feb 07, 2016 | Cars & Trucks
May 04, 2014 | 2008 Chevrolet Malibu
Feb 09, 2011 | 2008 Chevrolet Malibu
Jan 12, 2011 | 2008 Chevrolet Express
Dec 23, 2017 | 2008 Chevrolet Express
Jul 28, 2010 | 2008 Chevrolet Silverado 1500
Mar 12, 2010 | 2008 Chevrolet Express
Mar 02, 2010 | 2008 Chevrolet Malibu
203 people viewed this question
Usually answered in minutes!