Question about Dodge Cars & Trucks

Open Question

Code po036 in a dodge dakota

Had traced the wires back to pcm and no breaks cleared code comes back right away

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2000 Jeep Grand Cherokee Laredo PO123

I have ordered a reconditioned pcm for my Jeep. Once I have installed it I will get back to the forum and let you know if this fixed the problem

Thanks

Posted on Nov 07, 2008

simard2
  • 124 Answers

SOURCE: Where is the EGR valve in my 2005 Dodge Ram 1500 4.7?

Go to the following page to view more information on your EGR Valve:

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800ba857

Hope you find what you are your looking for! Good Luck!
If you have any more problems let me know.

Thank you for using Fix Ya!

Don't forget to rate the overall satisfaction of this answer!

Posted on Jan 31, 2009

csmock132
  • 4669 Answers

SOURCE: 2003 dodge dakota 4.7 auto.quad cab stalls for no

Check Engine Light? Any codes? Possible cam or crank sensor.

Posted on Mar 02, 2009

csmock132
  • 4669 Answers

SOURCE: PCM Troubleshooting Check light on with no code reader power

You can't jump the connector to get codes on OBD II. (Pre 1996) Try hooking back up you code reader. If it doesn't communicate, check the fuse for the cig lighter. This fuse should also power up the diagnostic plug.

Posted on Mar 09, 2009

  • 4044 Answers

SOURCE: i have 02 dakota with

Check your fuel pump pressure at the rail. These codes are an indication that the fuel pressure sensor is faulty or the fuel pump is not bringing the Fuel pressure to the proper level. The first is a warning there is a problem, the second is telling you the pressure is too high which can cause damage to the injector assemblies. The only things that increase pressure are a faulty Fuel pump or blockage issue. This is possibly caused by the Filter being partially clogged and the pump nit compensating but is most likely the fuel pump itself.

Posted on Sep 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

01 dodge dakota 3.9. no power to coil replaced engine control relay still no power can jump across relay get power but no start and get code for no rpm


If you're getting a code for no RPM, the PCM is not receiving a signal from the crankshaft position sensor. The PCM uses the signal from the crankshaft position sensor to fire the coil/spark plugs. Check the wiring to the crankshaft position sensor and check the sensor itself.

Oct 29, 2016 | 2001 Dodge Dakota

1 Answer

Wiring diagram running light, need wiring diagram for 2006 dodge dakota ,right tail light is out but brakeand turn signal works


With a test light check if you have power there with lights on and with lights off, compare left side with right side as far as location in the tail lamp plug for the tail lamp park lights.Trace the harness back to the left side underneath usual corrosion in this area.

Aug 30, 2014 | 2006 Dodge Dakota

1 Answer

Trouble code p1491, rad fan relay.


Did you clear or erase the codes after you replaced these parts?

Dec 05, 2013 | 2000 Dodge Dakota Quad Cab

1 Answer

95 Dodge Dakota 3.9 , voltage regulator is over chargeing battery.


Hate to say it, but probably a faulty PCM.
The regulator is directly controlled by the PCM on most models.
You might try a used PCM to make sure, or exchange the rebuilt under warranty.

Jul 01, 2012 | 1995 Dodge Dakota

1 Answer

2001 Dakota compression loss, smells like gas, white smoke from exhaust


Sorry but this has happened to me before, you might have a blown head gasket. that is where oil and or water are getting in to the piston cylinder and causing the white smoke cause the oil and water is being burnt or boiled.take it to a shop unless you have all the right tools and knowledge to do this job. i cost me like $1500 labor and parts.

May 26, 2012 | 2001 Dodge Dakota

1 Answer

Have a 2000 dodge dakota 3.9 2WD truck shifts great when check engine light is on but when you clear the codes it will not shift until the lite comes back on then its fine again. Dave


well if all ur doing is clearing the codes ur not to worried about what the actual problem is so just leave the light on but other then that find out what the code ur getting means an fix the problem an it will stop doing that just cause u clear the codes doesnt mean the problem goes away

Apr 20, 2011 | Dodge Dakota Cars & Trucks

1 Answer

P 206 engine code what does this mean on a dodge dakota 2001?


This code refers to a bad fuel injector circuit for your number 6 cylinder. There may be a short in the wiring coming from ecu (electronic control unit/computer) to the injector somewhere and the problem would have to be traced from injector back to source. You can do this yourself with a multimeter by checking input voltage with that plug and comparing it to another one which is good. If you get no reading at connector try checking that point coming from the ecu to determine is you have either a break between those points or if its a problem with the computer itself. Haynes service manuals have detailed wiring schematics to make it simplier in tracing wiring (get them at your local parts store fairly cheap) good luck and let me know if you need any further help

Jan 09, 2011 | Dodge Dakota Cars & Trucks

1 Answer

Check Engine Light comes on and off w/ P0304 code


this may be a defective fuel injector or a defective PCM (powertrain control module).

May 30, 2009 | 2000 Dodge Dakota Quad Cab

2 Answers

Obd codes


did computer check.... codes are 920, 921, 950, 999 what is this..... meaning?

Jun 20, 2008 | 1999 Dodge Dakota

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...