Question about Cars & Trucks

1 Answer

Where is the diagnostic port located on an isuzu trooper 1995 V6 model

What does it look like and how many pins does it carry?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 76,649 Answers

You can get the check engine light codes yourself on 1985-94 Isuzu vehicles by using a jumper wire between terminal pins 1 and 3 or A and B in the diagnostic connector. This diagnostic connector can be located anywhere from the driver side kick panel, passenger kick panel and sometimes at the center console. When using A and B terminal pins, getting the codes is similar to GM vehicles. Once the jumper wire is connected, turn your key on and read the codes being flashed in the dash panel.


where is the diagnostic port located on an isuzu t - 11_2_2012_5_38_56_pm.jpg

Posted on Nov 02, 2012

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Mr BrokRench
  • 1623 Answers

SOURCE: Location of the a/c low pressure port in a Isuzu trooper 91 v6

On or near the receiver/dryer.

Posted on May 21, 2009

  • 508 Answers

SOURCE: Location of the a/c low pressure port in a Isuzu trooper 91 v6

The low pressure side is the line that gets cold when the ac is running. It usually will have an inline dryer canister attached to it. Kind of about the size of a 16 ounce beer can. Close by you should see the port connection to add more freon or r-134 whichever your system uses.

Posted on May 22, 2009

  • 10 Answers

SOURCE: where is my oil pump

The oil pump is in the oil pan. the lifters will continue to tick until they are properly oiled. Be careful not to use to thick of oil as this will only make the pump work harder and could further damage your engine.

Posted on Sep 18, 2010

airjer995
  • 5332 Answers

SOURCE: need to locate auto trans

I'm pretty sure that year does not have a dipstick or dipstick tube. Instead there will be two drain plugs on the transmission pan. One is the drain plug and the one more to the rear and to the side (i'm going off memory here so I might be wrong) if the fill plug. The engine will need to be running when you remove the fill plug. I will warn you that it is common for the nut for the fill plug to break loose inside of the drain pain making it impossible to remove. The fix for this is to replace the pan. If you get the plug out you will need to use a pump to add fluid to the trans until fluid starts to come out of the fill hole. When the fluid is done draining back out the trans fluid is full and the level plug can be reinstalled. Have a drain pan under the trans before you start removing the fill plug to catch any fluid that may come out or any fluid that comes out after you fill the trans. If you have any questions i'll be happy to answer them.

Posted on Sep 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the location of the camshaft sensor for 1995 Isuzu Trooper


no engine stated, 4 banger or v6 but same answer.
there is no such sensor until 1996
why not post the problem or a symptom
and ask for help.
like
wont' crank.
cranks but will not start.
starts and stalls.
starts, runs but misfires.
like that.
get a tuneup yet?> (crystal ball)
V6 (guessing yours)
if you meant crank sensor its on the right side of engine block center.

seen here, CKP "crank sensor"
if you look for a CMP on line you will find it
but its Bunk, it's not there, stores mix parts up. et cetra.
http://jeepdied.com/look/alien-stuff/Isuzu/head%20cam%20sensors/CMP-wonder.pdf


836e5646-c779-44fe-b203-3249404738be.jpg

Dec 20, 2016 | Isuzu Trooper Cars & Trucks

1 Answer

What does this code mean? No tach signal to ECM - No Distributor Reference Pulses{4}


ISUZU INFORMATION AND LINKS - Front Range 4x4 Forums

www.frontrange4x4.com > Forum > Tech Topics > Make & Model Links
Apr 7, 2008 - 8 posts - ‎2 authors 12 No tach signal to ECM - No Distributor Reference Pulses{4} ... solenoid circuit failure - 1987 and 1995 Amigo/Pick-up, 1989 to 1994 V6 models ... {9}-Amigo, Pickup,Rodeo & Trooper w/2.6L engine & 1988-91 Impulse.

Sep 18, 2015 | 1995 Isuzu Trooper

1 Answer

V6. What are the size and length of the starter mounting bolts?


Probably 12mm X 1.5mm. Length is about 1 1/2 inches and 3 1/2 inches. They are metric.

Aug 06, 2015 | 1995 Isuzu Trooper

2 Answers

Where is the obd port on my 1993 isuzu Amigo


wow no engine size stated, and MATTERs.!
with no tech1 or 1a scan tooL (real scan tools)
what good is DLC?>
sure jumper CODES< (DTC errors in todays parlance)
there is abs tool.. but only on some cars.

and more. read the FSM yet?
lets pretend you said how do i get the PCM flash error codes
easy jumper the DLC. 'diag, link connector"

google Isuzu DLC jumpers, nets you all this.

http://www.troublecodes.net/isuzu/

there is no world standards for OBD1 so DCL are
every freakn where.

in cab or engine bay or like hondas, on PCM casiing
wild and wolly DLC>


quote

Multi-Port Fuel Injection

Amigo,Trooper II , Rodeo & Pickup
On Rodeo, Amigo, and Pickup (except 1993-95 models W/3.2L engine), connect the single wire diagnostic leads located behind the left hand kick panel together. On 1993-95 Rodeo models W/3.2 engine, the data link is located under the left hand side of the instrument panel. On all models, turn the ignition switch to the On position. At this point, the "Check Engine" light should flash. codes


25011203-uqsqk1sqel1nykdqv4diatnw-3-0.jpg 12pin version below.
jump pins,(for PCM errors) pins A > B
25011203-uqsqk1sqel1nykdqv4diatnw-3-1.gif
the codes are here.
http://www.troublecodes.net/isuzu/iszucel/





25011203-uqsqk1sqel1nykdqv4diatnw-3-3.jpg see no in the engine bay at all, like the 1 guess

Aug 26, 2014 | 1993 Isuzu Amigo

2 Answers

Where is the timing marks in isuzu trooper1995?


the timing marks are on the top (camshaft)and bottom (crankshaft)pulleys,but you may have to clean off the faces to see them,try using chalk.

Apr 18, 2010 | 1995 Isuzu Trooper

1 Answer

I need a belt diagrame of a 1996 V6 isuzu trooper


Click on the following free, direct Link. It has the Belt Diagrams for your 1996 Isuzu Trooper with the 3.2L DOHC V6. It also has the positioning for what Belts go where on the Crank Pulley.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1996/make/isuzu/model/trooper/1996_isuzu_trooper_drive_belt_routing_diagram.htm

Apr 16, 2010 | 1996 Isuzu Trooper

1 Answer

Location of the a/c low pressure port in a Isuzu trooper 91 v6


The low pressure side is the line that gets cold when the ac is running. It usually will have an inline dryer canister attached to it. Kind of about the size of a 16 ounce beer can. Close by you should see the port connection to add more freon or r-134 whichever your system uses.

May 21, 2009 | 1993 Ford Taurus

2 Answers

Where is the obd port on my 1995 Isuzu Rodeo?


d2610cc.jpg
Here is a photo of the obd connector on a 1993 Isuzu Trooper.

The connector is on the transmission hump about 6 inches from the accelerator pedal. It is inside a black hood. Right next to the white OBD connector is an identical green connector that I have not tested.

The OBD port is a white 3 hole plug. Right next to it in the photo is a green 3 hole plug that I believe is for automatic transmission diagnostics. The plug is different from other plugs under the dash as it will not accept a .25" tab connector.

The picture shows a 20 ohm resistor being used to short pin 1 and 3 of the white plug. The resistor is to prevent a melted wire in case the plug shorted is the wrong plug.

To read the error codes from the engine computer, the mechanic is supposed to short pin 1 and pin 3 of the OBD port plug. Then the mechanic turns on the ignition switch and counts flashes of the "check engine" light to determine the error values being reported.

Jan 23, 2009 | Isuzu Rodeo Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...