Question about 2008 Dodge Grand Caravan

Open Question

2008 dodge caravan drink holder removal

How do i remove the front console drink holder

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: tensioner pulley 1995 dodge caravan

Hi my name is Allen!

To help you I need to know what engine you have?

For example; 3.0 liter or 3.3 liter

If it is the 3.0 liter the nut for the tensioner is toward the firewall side of the engine tucked tightly under the exhaust manifold, very hard to get too.

If its the 3.3 liter you would have already seen it, both have only one nut holding the tensioner on. This one is easier.

For further assistance contact me at FixYa!

Posted on Dec 28, 2008

Ad
  • 548 Answers

SOURCE: dodge caravan sliding doors

First, keep in mind that as you begin to remove these doors you run the risk of causing serious scratches to the paint and glass, so put some masking tape and/or plastic sheeting around both sides of the door (rear quarter panel and rear glass, front door and front door glass)
I would get a Haynes repair guide since that's what I have to work from and it will tell you step by step with pictures, what to do. It's not hard, but you need to get all of the attach points unhooked to be successful. Suggest you have a helper working with you to keep the door steady.

Posted on Jan 25, 2009

  • 840 Answers

SOURCE: 2008 Dodge Caravan Overhead Console Rattles

I hate to tell you this they really can not do anything they may just make sure its all pushed in/ What happens is plastic and plastic meet and when they shift it causes noise even if you took it back to dodge they would take it out and because all the snap ins are plastic it could make it worse I have seen that happen If you took it back to dodge atleast it would be noted every wherever you take the vehicle so thats the good news but its under warranty / Please rate my response Thank you very much

Posted on Jan 31, 2009

  • 285 Answers

SOURCE: removing/installing 2000 dodge grand caravan window glass

after u remove the bolts that hold it to the window regulator tip the window towards the front of the door and the top rear corner of the window should pop out and then u just lift hte window out,hope this helps

Posted on Sep 05, 2009

Testimonial: "Thank you!"

  • 1986 Answers

SOURCE: how do I remove the passenger side power mirror on 98 caravan?

If you're lucky, on the inside of the door, will be a triangular panel right behind the mirror that you can pop off. If you're not as lucky and it's one piece or the panel is blocked by the door panel, you'll need to remove the door panel to change it.

On the inside trim, you can remove screws (these screws may be covered by filler pieces or may be visible, or they may require you pry a plastic piece off that covers the screws) that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can remove the bolts holding the mirror onto the door

Posted on Oct 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the lower center console on a 2000 Olds Intrique


Item Part Number Description 1 060024 Floor console armrest 2 06010 Floor console storage bin 3 04338D Floor console finish panel (front) 4 044D90 Floor console finish panel (center) 5 - Floor console cup holder screws (2 required) 6 13562 Floor console cup holder 7 - Floor console front screws (2 required) 8 - Floor console rear screws (3 required) 9 - Floor console nut 10 045A36 Floor console Removal and Installation
  1. Position the seats as needed to remove the console.
  1. Disconnect the battery. For additional information, refer to Section 414-01 .
  1. Remove the floor console storage bin.
    1. Remove the 3 screws and the armrest.
    1. Remove the floor console storage bin screw.
    1. Remove the pin-type retainer.
    • Disonnect the electrical connectors.
  1. Remove the floor console front finish panel.
    • Pull upward from the front of the trim panel to release the retainers.
    • Disconnect the electrical connectors.
  1. Remove the floor console center finish panel.
  1. If necessary, remove the 2 screws and the floor console cup holder.
  1. Remove the 2 floor console front screws.
  1. Remove the 3 floor console rear screws.
    • To install, tighten to 4 Nm (35 lb-in).
  1. NOTE: Lift the console from the rear and slide it rearward to release the rear seat heater ducts from the instrument panel. Remove the nut and the floor console.
    • Disconnect the electrical connector.
    • To install, tighten to 8 Nm (71 lb-in ).
  1. To install, reverse the removal procedure.

Jun 10, 2015 | 2000 Oldsmobile Intrigue

1 Answer

How to install a center console on a pacifica


Hi Melissa, I'm glad to help, here is the instruction below I said I'd send. Have an awesome day.


23 - Body/Interior/CONSOLE, Floor, Front/Removal REMOVAL [img id=LOPTableImg src="https://w05.dealerconnect.chrysler.com/service/mds2002/common/images/collapse.gif"> Click to display a list of Labor Operations associated with this procedure 1. Remove shift bezel. (Refer to 23 - Body/Interior/BEZEL, Shifter - Removal) .
2. Remove transmission range indicator surround bezel Figure 1.
3. Remove two screws attaching front floor console to the lower instrument panel Figure 2. 4. Open cup holder and remove two attaching screws to bottom of cup holder. 5. Open bin and remove two attaching screws to bottom of bin. 6. Remove front floor console sidewall attaching screws, three per side. 7. Raise front floor console and disconnect wiring harness. 8. Remove front floor console from vehicle.
374297.jpg Figure 1 - TRANSMISSION RANGE INDICATOR SURROUND BEZEL 1 - INSTRUMENT PANEL 2 - AUTOSTICK SHIFTER ASSEMBLY 3 - TRACTION CONTROL SWITCH 4 - TRANSMISSION RANGE INDICTOR SURROUND BEZEL 5 - KNOB SET SCREW 6 - SHIFTER KNOB 7 - FLOOR SHIFT BEZEL 8 - WIRE CONNECTOR 9 - INSTRUMENT PANEL WIRING HARNESS 10 - INSTRUMENT PANEL WIRING CLIP
374299.jpg Figure 2 - FRONT FLOOR CONSOLE 1 - FORWARD CONSOLE CLOSEOUT PANEL 2 - CLOSEOUT PANEL PUSH PIN RETAINER 3 - INSTRUMENT PANEL WIRING 4 - FLOOR CONSOLE BASE 5 - FRONT FLOOR CONSOLE ATTACHING SCREWS TO LOWER INSTRUMENT PANE AND BASE 6 - FRONT FLOOR CONSOLE WIRING CONNECTOR 7 - FRONT FLOOR CONSOLE 8 - ATTACHING L-BRACKETS

May 17, 2014 | 2006 Chrysler Pacifica

1 Answer

I'm an idiot and put my engagement ring in my change holder in my 2006 Chrysler Pacifica. When I went to put it back on, it was no where to be found. I believe it slipped behind the small crack


Print I hope this helps you,good luck.Randy


Removal & Installation

Instrument Panel

  1. Disconnect and isolate the battery negative cable.
  2. Remove the center console closeout panel by removing the left and right attaching screws, then the left and right panels.
  3. Remove or disconnect the following:

    Remove the shift bezel. Remove the transmission range indicator surround bezel. Remove the two screws attaching the front floor console to the lower instrument panel. Open the cup holder and remove the two attaching screws on the bottom of the cup holder. Open the bin and remove the two attaching screws on the bottom of the bin. Remove the front floor console sidewall attaching screws, three per side. Raise the front floor console and disconnect the wiring harness. Remove the front floor console from the vehicle.

    0996b43f807cb4f3.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of front floor console and shift bezel


    0996b43f807cb4f4.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of front floor console, showing attaching screws

  4. Remove the floor console base assembly by removing the two screws attaching the L-brackets to the instrument panel.
  5. Remove the nuts attaching the floor braces to the instrument panel.

    0996b43f807cb4f5.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. View of floor brace, attaching nuts, center brace, and floor bracket

May 02, 2012 | 2006 Chrysler Pacifica

1 Answer

I am not getting any heat from the front control


If your getting air through the vents but it wont get warm it's probably the Air Blend Actuater Door Motor located behind the radio. You can get to it by taking the bottum panel off under the ashtray drink holder. remove the ashtray/drink holder and you will see it,it has three screws holding it on. When you take the old one off and you can move the the plastic piece on the back then it needs replacing.I just changed one in my mom's mini van now she has heat a lot of heat.An average person can do this repair in about 30 minutes.

Dec 29, 2011 | 1999 Ford Windstar

1 Answer

Need to remove center console to replace seat belt. After removing 12 screws, console is still firmly in place. What else has to be done?


  1. Remove the two oval covers from the sides of the floor console. Remove the four (two on each side) retaining bolts. Lift or remove the front seat center armrest from the floor console.
  2. Remove one screw from the top rear end of the floor console (directly under the front seat center armrest.
  3. Remove four screws retaining the utility tray beverage holder to floor console. Lift or remove the utility tray beverage holder from the console.
  4. Remove two screws (directly under the utility tray beverage holder) retaining the front end of the floor console to the console panel front mounting bracket.
  5. Lift the floor console from the front and rear console panel mounting brackets.

Feb 27, 2011 | 1996 Ford Explorer

1 Answer

The front cup holder is off track. How do I fix this?


Just did this myself.
Open the front compartment under the drink holder, lightly push to one side and then pull on the side where the crack you've just made is to disengage the clips, repeat for the other side.
When you have that cleared, remove the screws that have the face plate attached to the drink holder.
Stick your hand up in through the hole where the lower compartment was and with the other hand push the drink holder in and out, changing the angle a little bit until you can pull it free.

Nov 19, 2010 | 2007 Chevrolet Uplander LS Minivan

1 Answer

Center console disasembly instructions . we are trying to remove the center console


Base Console, Floor, Ranger, Explorer Removal and Installation
  1. Remove the two oval covers from the sides of the floor console. Remove the four (two on each side) retaining bolts. Lift or remove the front seat center armrest (644A22) from the floor console.
  1. Remove one screw from the top rear end of the floor console (directly under the front seat center armrest.
  1. Remove four screws retaining the utility tray beverage holder to floor console. Lift or remove the utility tray beverage holder from the console.
  1. Remove two screws (directly under the utility tray beverage holder) retaining the front end of the floor console to the console panel front mounting bracket.
  1. Lift the floor console from the front and rear console panel mounting brackets.

c758709.gif

Apr 01, 2010 | 1996 Ford Explorer

1 Answer

I entered code# in book but shows err1,etc


Remove centre console drink holder then centre console watch for wires to cig lighter It all just unclips then pull firmly on ashtray assembly and you can get at radio Good luck

Jul 10, 2009 | 2001 Mitsubishi Diamante

1 Answer

How do i take off my center console to get to my distibiter cap


Directly below the ashtray there is a small cover that snaps in place....remove this cover to expose two 10mm nuts that hold the top of the "dog box" in place. There are also two on the bottom (just above the floor). Have both front seats pushed back as far as you can to allow more room. After the outer cover (glove box/drink holders) are out of the way there will be a cross strap that holds the inner cover in place. remove that strap by pulling down on the handles in the front and then pull the engine cover off and out of the way. The distributer is right there on the top of the motor.

Feb 27, 2009 | 2002 GMC Savana

1 Answer

1996 accord center console


If your vehicle is an automatic, it should light up your console where the gears are marked. There's a bulb under the console. in order to get to it, you'll need to empty the console and remove the plastic piece covering the screws (very bottom of console middle) and remove the screws. Then you'll need to remove the drink holder (pops out) and remove the screws under it. Lift the rear piece of the console over the E brake, and loosen the screws to the piece with the gear indicator. You should be able to see the lamp holder and twist lock connector. If the connector hasn't just fallen out, replace the bulb and twist the connector securely back into place.

Feb 21, 2009 | 1996 Honda Accord

Not finding what you are looking for?
2008 Dodge Grand Caravan Logo

Related Topics:

298 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6918 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...