Question about 2006 Chevrolet Aveo

1 Answer

Install a aveo map sensor

Where is the map sensor

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Chevrolet Master
  • 2,620 Answers

Usally there mount on top of the intake manifold.

Posted on Nov 02, 2012


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Fuel pump relay

Run fault codes and check for idle speed sensors/MAF/MAP sensors. If the pump was faulty then it would not supply fuel to the manifold. Test it by having a pressure test done on the fuel. manifold

Aug 25, 2013 | 2005 Chevrolet Aveo

1 Answer

2006 aveo stalling and no power. # 1 cylinder not firing properly. Start it again and for a couple of minutes starts running rough again. changed plug and checked spark, both ok. ses codes p0106 the first...

code p 0106/7 refers to manifold absolute pressure (MAP) and BARO pressure sensor --range /performance and low input problems ===causes wiring ---MAP sensor---Baro sensor --wiring short to ground ---ECM
no 1 not firing would be a problem injector

Oct 29, 2017 | 2006 Chevrolet Aveo

2 Answers

Where does the map sensor sit

Hi, see the picture below. Before replacing the MAP sensor, check the vacuum line for leaks. If the vacuum is good and you have a voltmeter, check the signals. With the key on, there should be 5 volts DC between the outer terminals of the connector. Don't take it off--just stick your meter probes in the back of the connector until they touch the bare wires. If you don't have 5 volts there, the problem is not the sensor--it's the wiring or the computer. If you do have 5 volts there, check the voltage from the white wire to either of the other 2. That voltage should be between 1 and 5 volts, and it should change a lot when you start the engine. If it doesn't change at least a couple of volts, the sensor is probably bad. Please let me know if you have questions, and thanks for using FixYa.



Sep 03, 2011 | 2006 Chevrolet Aveo

1 Answer

Check engine light came on and is giving codes P0171,P0106,P0172,P2188, P2187. What do these mean?

check for a broken vacuum hose or vacuum fitting(s). you can use a can of spray carb cleaner. while running the engine use the spray to test hoses and fittings. give a little squirt to suspected areas. The idle speed will change when you find a vacuum leak. pay particular attention to the hose to the MAP sensor. There may be a problem with the elelctrical connection to the map sensor, or the sensor itself may be bad.

Manifold Absolute Pressure Sensor printpage_icon.gif


Oct 22, 2010 | 2006 Chevrolet Aveo

3 Answers

2005 Aveo; hold light blinking, check engine light on, car chugs

Try a toon-up..
Or might be a sensor.. There are several..
Trying to figure these things out is a process of elimination.. Unless looked at by a shop..

Hope this helps !!
rate me good ;o)

Jul 13, 2009 | 2004 Chevrolet Aveo

3 Answers

Hold light blinking, check engine light on, engine slows down

check tps sensor (throttle position sensor in backside of the throttle cable) and map sensor (manifold absolute pressure on front little 1 inch sensor with vacuum line) make sure there plugged in. the ecm (engine control module driver side inner fender) and tcm (transmission control module under dash) both need the data to know when to upshift and increase fuel/air. Otherwise the computer runs default values and guesses off of other sensors giving poor performance. also disconnect battery for 15 min. usually resets aveo service lights if you dont have a scanner.

Jul 13, 2009 | 2004 Chevrolet Aveo

1 Answer

Car will turn over but will not start 2005 aveo

Suggest look under the hood for any wires or connectors you might have bumped loose while repairing the MAP sensor.
Check to see that you are getting a spark to the plugs.
Use care because you are dealing with high voltage and could get zapped.
If still same problem suggest obtain a good Volt/Ohm meter and trace-out your circuits to find the problem.
Shop manual with wiring diagrams is a must have for this.
Sometimes they are available online for free as a PDF file.
Be safe when working with electrical parts.

Dec 15, 2017 | 2006 Chevrolet Aveo

1 Answer

2004 aveo wont start

sounds like it was burning real rich if it melted the o3 sensor harness chances are the converter melted inside and is restrickting the exhaust if you unhook the exhaust at manifold and it runs replace converter and fid out what is making it run rich before you burn out new converter

Oct 02, 2008 | 2006 Chevrolet Aveo

Not finding what you are looking for?
2006 Chevrolet Aveo Logo

Related Topics:

177 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides