Question about Cars & Trucks

1 Answer

I changrd out o2 sensors po171,po174 and po340 and reset drove 100miles light came back on checked it again and said thoughs sensors were bad what could the problem be?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 54 Answers

Shorting out bare wires

Posted on Nov 02, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 66 Answers

SOURCE: O2 sensor problem

I have a 97 gmc sierra .This truck is the same as the chevy ok.Its a 350 5.7 liter 4x4 Z71.I took it to auto zone which was my first mistake.They put it the scanner and said bad O2 sensor.Ok so which one is it i said.They dont know.Well there four (4) O2 sensors in this truck i hope you know that.I had to replace all four of them before i had to take it to a real shop.It seems the fuel pump i replaced a week earlier with an auto zone fuel pump was bad.Ive changed my feul pump 4 times now and have 235000 miles on still running.You need to get your fuel pressure checked.It should be 65 psi to start it and 55 psi to run it.If the pressures are good it could be a different O2 sensor or maybe the mass air flow senor.My last option would be the fuel pressure regulator because it seems to be a waste of time and money.I would get that fuel pressue checked first.Good luck.

Posted on Nov 25, 2008

3mac
  • 61 Answers

SOURCE: 1995 Windstar OBD II showing codes PO340, PO171, and PO174.

Symptoms of a faulty Camshaft Position Sensor can include hard starting (or no starting), rough running/misfiring and/or loss of power.

Code 340 COULD be caused solely by a faulty Camshaft Position Sensor. However, this code refers to the entire circuit. So, replacing the sensor may not fix the issue. The problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM.

Codes 171 and 174 typically appear together. They are caused by the 02 sensors reading too much air (lean) in the exhaust. In most cases, simply cleaning the MAF sensor does the trick. I typically take it off and spray it with electronics or brake cleaner. Just make sure it dries before reinstalling. If this doesn't eliminate the codes, inspect all vacuum and PCV hoses, check for a dirty fuel filter and ensure the furl pressure is within limits.

For clarification, the first trip to the shop your car showed codes 402, 732, 733, 171 and 174. After changing the DPFE/EGR, did ALL those codes go away and now only codes 340, 171 and 174 exist? Or do you have the second set of codes in addition to the first codes?




Posted on Jan 15, 2009

  • 195 Answers

SOURCE: 1995 Windstar OBD II showing codes PO340, PO171, and PO174

Hello;
With those codes, the first place I would check is the fuel pressure. Also check the fuel filter and replace it if you haven't already. Then clear codes and recheck. Even if your fuel pressure is with in range it still may not push enough fuel to operate your vehicle.

Posted on Jan 15, 2009

  • 1 Answer

SOURCE: 1998 FORD EXPLORER SPORT 4X2 4.0 OHV

I have 98 explorer im getting same codes ive worked on cars all my life I havent replaced anything but my fuel filter so far on the explorer and that wasnt it.I know people tell you to replace all that other stuff,but if you know cars and how the stuff works thats on a car then you can fix anything with out people telling you;you need to buy this and then this and there just fishing when the dont know there as* and whole in the ground.Im going to replace my lower and upper intake seals like he says above.At least theres one more smart one out there and not someone that thinks they know it all like people that work in the parts places and some dealers.

Posted on Jan 23, 2009

moparownr
  • 667 Answers

SOURCE: code po171 7 po174

your computer is reporting bank 1 and 2 too lean, usually caused by the mass air flow (MAF) sensor, you can usually clean this sensor and reset the light. Clean it with electric cleaner or brake cleaner, make sure it is dry before reinstalling, also take care not to damage it. Hope this helps, let me know

Posted on Jun 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I HAVE CODES PO171 AND PO174 04 CADILLAC SRX 4.6L


please go to : repairpal.com/obd-II-code-po171-and-PO174 FOR MORE INFO, good-day!

Apr 17, 2014 | 2004 Cadillac SRX

2 Answers

Check engine light on, 0430 code


This code is not uncommon with the X-Type, a dealer will recommend replacing the Cat. very expensive. get a 1" spark plug extender and drill a 1/2 hole through it and screw it into the lower O2 sensor hole for bank 2 (rear of the engine) and then screw the O2 sensor into it, reset the code and you should be all set.

Jan 04, 2014 | 2002 Jaguar X-Type

1 Answer

I have a 2004 ford f-150 heritage xlt. check engine light came on and codes are po171 and po174. my book tels me its system adaptive fuel too lean (bank1and2). how should i start my problem solving?


check bank 1 and bank o2 sensor wires make sure a mouse didnt chew them up most wires are soy based and them mouses chew them and make homes in the cabin filter in stuff if not you got bad o2 sensors

Dec 02, 2012 | Ford F-150 Cars & Trucks

1 Answer

Po171 po174 restricted performance


Common fault is leaking gasket on intake manifold towards the back, do you have the following symptoms - uneven idle - sudden cut out on idle but starts up again with no problem?
If so you will find a leak on the inlet manifold. The codes show a leak after the MAF- so this is the area to check. Hope this helps.

May 29, 2012 | 2003 Jaguar S-Type

2 Answers

Riding rough what do i change with these codes po171, po174, po300


171 and 174 are lean mixture codes, 300 is a random misfire (any cylinder). Check for a vacuum leak, listen for a hissing noise with engine idling.

Mar 04, 2010 | 2002 GMC Sierra 1500

1 Answer

2006 jeep wrangler code po174


Check wiring to sensors.

Jul 13, 2009 | 2006 Jeep Wrangler

1 Answer

Code po171 7 po174


your computer is reporting bank 1 and 2 too lean, usually caused by the mass air flow (MAF) sensor, you can usually clean this sensor and reset the light. Clean it with electric cleaner or brake cleaner, make sure it is dry before reinstalling, also take care not to damage it. Hope this helps, let me know

Jun 09, 2009 | 1997 Ford Thunderbird LX

3 Answers

1995 Windstar OBD II showing codes PO340, PO171, and PO174.


Symptoms of a faulty Camshaft Position Sensor can include hard starting (or no starting), rough running/misfiring and/or loss of power.

Code 340 COULD be caused solely by a faulty Camshaft Position Sensor. However, this code refers to the entire circuit. So, replacing the sensor may not fix the issue. The problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM.

Codes 171 and 174 typically appear together. They are caused by the 02 sensors reading too much air (lean) in the exhaust. In most cases, simply cleaning the MAF sensor does the trick. I typically take it off and spray it with electronics or brake cleaner. Just make sure it dries before reinstalling. If this doesn't eliminate the codes, inspect all vacuum and PCV hoses, check for a dirty fuel filter and ensure the furl pressure is within limits.

For clarification, the first trip to the shop your car showed codes 402, 732, 733, 171 and 174. After changing the DPFE/EGR, did ALL those codes go away and now only codes 340, 171 and 174 exist? Or do you have the second set of codes in addition to the first codes?




Jan 15, 2009 | 2001 Ford Windstar

1 Answer

1995 Windstar OBD II showing codes PO340, PO171, and PO174


Hello;
With those codes, the first place I would check is the fuel pressure. Also check the fuel filter and replace it if you haven't already. Then clear codes and recheck. Even if your fuel pressure is with in range it still may not push enough fuel to operate your vehicle.

Jan 15, 2009 | 1995 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...