Question about Cars & Trucks

1 Answer

2003 crown vic police car cant do dianostics keeps saying no communacation with com all fuses check and are good

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 76,073 Answers

Duplicate question

Posted on Nov 02, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 178 Answers

SOURCE: 2003 ford crown vic hard steering

i would have to say to check for a relay in your fuse boxes for power steering pressre switch or it may have its own police pkgs have a lot of relays due to all the extras

Posted on Sep 11, 2008

ltfrc
  • 227 Answers

SOURCE: 2005 Crown Vic Police Interceptor: Starts then stalls

Have you checked the fuel filter. Fuel pump will pressure up, but fuel filter could be clogged and not work without the pressure of the fuel pump.

Posted on Jan 17, 2009

  • 14036 Answers

SOURCE: 2001 crown vic keeps burning 30A PCM relay fuse

have fuel pump checked i have known a bad fuel pump shorting out causing pcm fuse to blow.

Posted on May 10, 2009

  • 1 Answer

SOURCE: where is fuelpump on 2003 crown vic police intercepter

Dear cdkkks,

Replacing a fuel pump in modern cars requires some preliminary electrical, fuel test analysis work. I have noted some professionals indicating you need to run car until gas lines, tank is empty; more than likely, if your fuel pump is defective, you cannot start the car, car is unoperative; you will attempt to start car, starter will turn the engine over rapidly without starting, let's assume you are in this condition.

First we need to test the fuses and fuel pump relay, basically the electrical opportunities on your vehicle, the relay panel is on the fender well, driver side, lift the relay control assembly from the fuse center and press the tab on the end, push down and this will release relays from the cover. This relay control panel includes the PCM power relay (left side in original position) Fuel pump relay (Center) this is the relay you are concerned with and the Air Conditioning relay on (Right). If you have friends, or associates who have electrical equipment to test the fuel pump relay, utilize their help, some automotive shops will provide this service. Checking the relay circuit with a jumper wire, any scrap piece of wire, 16-18 gauge will do; as you are looking directly down at the relay opening, you will note an opening at the 6:00 and 12:00 clock positions, 6:00 is the positive, 12:00 is the neutral, volt meter set for volts will confirm. Open the gas cap from the fuel tank filler pipe, insert the jumper wire and carefully listen for a whirring sound. If there is no sound and you have confirm electrical pump fuses, fuel pump relay is working properly (Voltage is pressure, battery voltage and slightly less voltage at the relay circuit when ignition key is turned on) then we have couple more checks to perform before we replace fuel pump. Let's check the fuel rail pressure on your Ford Crown Vic, obtain a fuel compression gauge with a Ford Schrader valve adapter, check to verify that no fuel pressure exists. If "NO" fuel pressure exists, and we have confirmed the voltage integrity of relay/fuel pump circuit, then we are ready to remove fuel pump. Use a simple gas siphoning kits from your local auto parts outlets to safely remove all remaining gas from gas tank, use appropriate gas tanks to store fuel; safety is the key here, gas and gas fumes are extremely dangerous; use appropriate chemical/gas gloves when siphoning/handling gas.

(A) Park your Crown Vic, perferably in a garage, concrete floor and make sure there is enough room around the back of the vehicle for you to work and move tools around.

(B) Raise the back of your car using a floor jack and support it safely on wheel/jack stands; remember, the driver side rear wheel must be removed in order to remove the fuel tank filler pipe, place your wheel stand (supplement with 2 by material for proper height on frame,slightly forward of rear wheel); safety is the key issue here and I cannot overly emphasize this issue, heavy wheel stands should be supporting the right rear wheel and frame, slightly forward of rear wheel, driver side).

(C) Disconnect the fuel tank filler pipe and the fuel pump connector located above the cross member underneath the vehicle, you must remove the (3) screws on the topside (fuel tank fiiler pipe) and approximately (4) screws on the bottom side, and the (1) screw adapter plate where the fuel tank filler pipe is inserted into the gas tank, top of wheel opening, underneath the vehicle. After these connections are removed, push the fuel tank filler pipe further into the fuel tank, allowing you additional room to lower the filler pipe from it's current position, downward; once you have sufficient clearance, twist, turn left, slightly back and forth movements and carefully pull outward, removing the filler pipe from gas tank. Do not damage the rubber groment in gas tank as you remove the filler pipe. As a note, when you reinstall the filler pipe, insert small amount of vasoline on filler pipe end that is inserted into the gas tank to facilitate the installation process.

(D) Support the fuel tank with a jack and remove the nuts from the holding strap using a wrench or ratchet and socket. Move the strap away and slightly lower the fuel tank in order to disconnect the vapor tube from the tee connector on the right and the vapor line from the canister tube. Discard the fuel tank mounting studs and replace with new fuel tank mounting studs on the reinstallation process.

(E) Unplug the pressure transducer electrical connector located on the top rear corner of the fuel tank.

(F) Clean area around the mounting fuel pump mounting flange. Remove/disconnect the fuel lines attached to fuel pump mounting flange then remove the fuel pump mounting flange mounting bolts in a crisscross pattern.

(G) Lift the fuel pump assembly off the tank. Replace the new fuel pump in the assembly and install the assembly in the tank. Install the flange screws and torque to approximately 89 inch lbs using a crisscross pattern. If no torque wrench is available, tighten to a snug fit and stop.

(H) Afterwards, raise the fuel tank enough to attach fuel lines and vapor lines indicated above, item D. After connecting all lines, raise tank with floor jack to its original position "carefully" and utilize the new mounting bolts, securing straps in their original position and torque bolts to approximatlely 25-30 lbs torque.

(I) Install the fuel tank filler pipe per the aforementiond process reversed.

(J) Review your connections and then carefully lower the vehicle, use a gas container, input 4-5 gallows of gas and start the engine and check for leaks.

Wishing you the very best,

drprice

Posted on May 20, 2009

  • 66 Answers

SOURCE: 99 crown vic police interceptor steering wheel??

i have ran into 2 issues in these vehicles---if it binds while sitting still also, check the steering shaft, i have found the u-joints in the shaft tighten up and binds dangerously tight---if they are free, sounds like you may have a steering box issue or restriction in a line---hope this was helpful!!

Posted on Jul 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuse for a cigarette lighter in a 2003 Crown Victoria Police Interceptor?


fuse panel is below and to left of steering column by brake pedal fuse number 25 page 166 and 167 of owners manual following link is your owners manual for 03 crown vic
2003 Ford Crown Victoria Owner Manual

Aug 10, 2016 | Cars & Trucks

1 Answer

2003 ford crown vic police car unalbe to do dianostics keeps saying unable to connect to pcm done checked all fuses and wiring looks good


Check pin #16 of diagnostic connector it should have 12 volts. See diagram below. Also did you check the fuses under the hood?
11_2_2012_12_22_39_am.jpg

Nov 01, 2012 | Cars & Trucks

1 Answer

Fuse panel diagram 2006 crown vic


The diagram is part of the owners manual, you can access a free pdf copy HERE.

Jun 01, 2012 | Cars & Trucks

1 Answer

Brake light wont work on police interceptor 2004 victoria


First check fuse for brake light with test light if fuse is good test brake light switch under dash with test light if you dont understand how to do the above contact me at Ken17402@msn.com title the message crown vic problem

Nov 15, 2010 | 2004 Ford Crown Victoria

1 Answer

2003 Crown Victoria: lost my only key to my 2003 police cron vic....


not to sound crazy ! do u own this car out rite! if so you can go to the dealer with the reg and they can cut u a key through the vin number! the key will cost 30 to 45 dollars ! its cheaper than a locksmith

May 05, 2010 | 2003 Ford Crown Victoria

1 Answer

2003 CROWN VIC HAS NO SPARK AND NO POWER TO FUEL PUMP CHECKED RELAYS AND FUSES CHANGED CRANK AND CAM SESOR LOOKED FOR BAD GROUND AND BROKEN WIRES AND HELP PLEASE


DID YOU CHECK THE FUEL PUMP SHUTOFF SAFETY SWITCH ON THE LH/DRIVERS SIDE IN THE TRUNK & MAKE SURE IT IS DOWN ,& EVEN IF IT IS SOMETIMES YOU CAN TAKE SOMETHING & PUSH IT UP & THEN PUSH IT BACK DOWN & IT WILL CRANK,& BELOW THAT SWITCH IN THE TRUNK IS A FUEL PUMP DRIVER MODULE ,IT MAY BE BAD,THOSE ARE A COUPLE OF THINGS THAT HAVE WORKED FOR ME ,& THATS PRETTY MUCH ALL I DO IS WORK ON FORDS, & LX CROWN VICS & P71 POLICE CROWN VICS WHERE I AM WORKING, HOPE THAT IT MIGHT HELP YOU FIX IT. SEAN

Nov 02, 2009 | 2003 Ford Crown Victoria

2 Answers

Check engen light keeps coming on


It is located in the rear under the fuel tank.You will see a black plastic cover over it.

Jun 24, 2009 | 2003 Ford Crown Victoria

2 Answers

I have a 2003 Crown Vic The air conditioning don't work, Where do I start looking for the problem? Is there a Fuse I can check?


When the Police decommissioned the car they removed Relay 204 in the fuse box under the hood. I replaced the Relay. Problem solved.

Jun 22, 2009 | 2003 Ford Crown Victoria

1 Answer

2003 ford crown vic hard steering


i would have to say to check for a relay in your fuse boxes for power steering pressre switch or it may have its own police pkgs have a lot of relays due to all the extras

Sep 10, 2008 | 2003 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

233 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...