Question about 2006 Hyundai Sonata
Which O2 sensor needs replacing?
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
there is two wires then suposed to be same color they are not what you looking for but if you have a grey and a black wires it willl be one of those i hope and this help
Posted on Jun 20, 2008
SOURCE: check engine light on,2 days
This is a trans range switch code, try this: on top of the transmission, by the selector lever, there is the range switch, remove the electrical connector to the switch and clean the terminals inside the connector, add some dielectric gears to the terminals (avail at any parts store), and reconnect. Disconnect negative battery terminal for 60 sec., reconnect switch, drive the car a few d ays and see if MIL light come on again.
Posted on Aug 28, 2008
try autozone.com to see if they have your car listed for diagrams pictures and step by step instructions if your car is not listed then try your local library they have all the car manuals and even copy them for you
Posted on Mar 20, 2009
This is a very simple repair just make sure the car is overnight cold and use antiseize compound . Also sign up for this site all the diagrams you could want http://www.hmaservice.com/
Posted on Jul 01, 2009
You need to check two things.
First, there is a heat shield on top of the front of the motor where the o2 sensor you already replaced is. It's got (4) 12mm bolts. Remove it and check the exhaust manifold (big thing you put the o2 sensor into) for cracks. If there are any cracks, you'll get o2 sensor codes. Replace the manifold.
Second, if the manifold is fine start the car and listen to the exhaust pipe under the engine for leaks. Or if you already know the exhaust is loud... that's gonna do it too. A leaking exhaust pipe on an Accent will set secondary o2 sensor codes.
SHOULD you try to change it yourself, you will need a 7/8" wrench, and a new o2 sensor, or flex pipe, or manifold depending on what's broke. Do NOT touch the tip of the new or old o2 sensor to ANYTHING when you take it out or install it or it will be ruined permanently. Run the car until it's at it's normal operating temperature. Raise the vehicle, and take the o2 sensor out of the car (see below to understand which one) using the 7/8" wrench or if you got fancy and bought an 02 sensor tool... use it.
Replace whatever parts are bad (manifold or pipe) or just replace the sensor you need. Then restart the car and take it to a parts store and have them clear the code. The code (and check engine light) won't return right away, it usually takes a few days. If you did everything right you should be good. If not, it's not a terribly expensive job to have done and by now you should be able to explain to them what's wrong based on what you found when you looked at the car. Just tell them everything you checked and what you saw.
Education: I'm not sure where that half baked answer about o2 sensor 1 being near cylinder one came from but here's the real deal.
Sensor 1 is always BEFORE the catalytic converter
Sensor 2 is always AFTER the catalytic converter
Bank 1 and Bank 2 refer to which SIDE of the exhaust on 6 and 8 cylinder engines. Bank 1 is usually left side, Bank 2 is usually right side.
So... O2 sensor B1S1 refers to the O2 sensor BEFORE the converter on the LEFT side of the motor.
Posted on Nov 23, 2009
Tips for a great answer:
Jan 27, 2017 | 2008 Chevrolet Silverado
Apr 22, 2014 | 2006 BMW 325i
May 04, 2011 | Saturn LS Cars & Trucks
From this website:
P0140 - 02 Sensor Circuit No Activity Detected (Bank 1 Sensor 2)
What does that mean?
The Powertrain control module (PCM) will provide a .45 volt reference voltage to the Oxygen sensor. When the O2 sensor reaches operating temperature, it will generate a voltage that will vary depending on the oxygen content of the exhaust. Lean exhaust generates a low voltage (less than .45V) and rich exhaust generates a high voltage (greater than .45V). O2 sensors on a specific bank marked as "sensor 2" (as this one is) are used to monitor emissions. A Three-Way Catalyst (TWC) system (catalytic converter) is used to control tailpipe emissions. The PCM uses the signal received from Oxygen sensor 2 (#2 indicates aft of catalytic converter, #1 indicates pre-converter) to read efficiency of TWC. Normally this sensor will switch between high and low voltage at a noticeably slower rate than the front sensor. This is normal. If the signal received from rear (#2) O2 sensor indicates that the voltage has "stuck" between .425V to .474 V, the PCM determines this sensor is inactive and this code will set.
Your check engine light(CEL), or malfuction indicator lamp (MIL) will be illuminated. There will not likely be any noticeable drivability problems other than the MIL. The reason is this: The rear or post catalytic converter Oxygen sensor does not affect fuel deliver(this is an exception on Chryslers). It only MONITORS the efficiency of the catalytic converter. For this reason, you will likely not notice any engine trouble.
The causes for a P0140 code are fairly few. They could be any of the following:
Shorted heater circuit in O2 sensor. (Usually requires replacement of heater circuit fuse in fuse block also)
Shorted signal circuit in O2 sensor
Melting of harness connector or wiring due to contact with exhaust system
Water intrusion in harness connector or PCM connector
This is a fairly specific problem and shouldn't be too difficult to diagnose.
First, start engine and warm up. Using a scan tool, watch the Bank 1, sensor 2, o2 sensor voltage. Normally the voltage should switch slowly above and below .45 volts. If it does, the problem is likely intermittent. You'll have to wait for the problem to surface before you can accurately diagnose.
However, if it doesn
Apr 15, 2011 | Dodge Pickup Cars & Trucks
Feb 06, 2011 | Hyundai Elantra Cars & Trucks
Aug 06, 2010 | Hyundai Elantra Cars & Trucks
Jan 31, 2010 | 2006 Hyundai Elantra
Jan 27, 2010 | Hyundai Motor 2002 Elantra
171 people viewed this question
Usually answered in minutes!