Question about Cars & Trucks

Open Question

Timeing marks for crank-cam-asseserydrive nta-855-c. cummins

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
psds4
  • 293 Answers

SOURCE: timing marks,cam and crank,2.4l

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528018d02c

Posted on Oct 09, 2008

Ad
alicantecoli
  • 22156 Answers

SOURCE: 1998 zx2 timing

timing mark is on flywheel for crank and on the rear end of the cams under the rocker cover.be carefull with this as the pulleys do not have keyways and can come loose resulting in smashed valves and piston.make sure retaining bols have locktite or better still araldite on the threads and use a impact gun on them.fairly easy job to do though,make sure you remove tensioner though and remove the dust cover and give a little drop of oil and some new grease then push seal cover back on ,saves the cost of a new bearing as these are not cheap.

Posted on Nov 09, 2008

gregstobbe
  • 56 Answers

SOURCE: timing mark for charade 90 model 3 cylinder

here is the site for timing marks.
http://www.2carpros.com/car_repair_information/tec_info/1990/daihatsu/charade/1990_daihatsu_charade_timing_belt_diagram_marks.htm
Ps. dont forget to rate my solution please. Thanks.

Posted on Dec 27, 2008

  • 137 Answers

SOURCE: NEED TIMING MARKS 2.0L DUAL CAM FORD CONTOUR

the cam marks are on the cams under the valvecover the crank has a mark o nthe timing cover that you need to line it up to

Posted on Jan 20, 2009

  • 1757 Answers

SOURCE: timing marks on twin overhead cams 2.4 and crank mark.

Click on the following direct, Free Link. It has several Diagrams including the Timing Belt + Marks for your 2004 Hyundai Sonata 2.4L DOHC In-Line 4-Cylinder Engine (located on the bottom half of the Page on the Link). There are additional Diagrams that will prove to be helpful while you are doing this...

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/2004/make/hyundai/model/sonata/2004_hyundai_sonata_timing_belt_diagram_marks.htm

Posted on Apr 16, 2010

Testimonial: "tHANKS, tHIS WILL DO THE JOB."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Instruction changing timing belt 1979 Alfa Romeo Spider Veloz?


With Cam Caps loosened, FIRST loosen timing chain tensioner, press it in to loosen tension, Crank using ratchet to TDC (Top Dead Center on crank pully, (to keep from damage to pistons), align Exhaust Cam Timing Mark to mark on #1 Exhaust cam cover, then take up slack between Exhaust & Intake Cams (on top between the cams), Then align the Intake Cam to mark on #1 Cam Cap, "Now" loosen the 17mm bolt to tighten timing chain, rotate engine using rachet two times, reset TDC at the crank, and look at "Cam Timing Marks on both the Exhaust, and Intake Cams. If you did all this correctly the "Timing Marks" should be lined up so TDC,Exhaust, and Intake marks are all the same.

Oct 10, 2014 | 1979 Alfa Romeo

2 Answers

Problems of gm


You can rotate the cam/crank into a positon that will not move as you remove the old belt, as long as the new belt places the cam/crank in same position as the old belt had them, it don't matter where the timing marks are. Leave your old belt on, rotate to a position that will not move or have tension on belt, (no matter the marks) and replace the belt. Make sure to recheck timing marks after new belt is installed by rotating the crank/cam back to timing marks, or just trust that the belt was replaced without the cam or crank rotated. Easy off, easy on, just make sure the cam/crank are still in time as the old belt had them located. NOTE: timing marks are there in case of a broke belt, or for a car that has jumped time. As long as cam and crank are held in same positon, and car was in time before the procedure, it don't matter where the timing marks are at during belt replacement.

Dec 15, 2013 | Cars & Trucks

2 Answers

Where is the timing marks on a 5.9 cummins 96 model


2_22_2013_3_04_32_am.jpghere is the timing diagram for a cummings 5.9 good luck

Apr 17, 2010 | 1996 Dodge Ram 2500 Club Cab

2 Answers

Cam Crankshaft timing


8 degrees before tdc

Mar 10, 2010 | 1983 Chevrolet Chevy

2 Answers

What are the symptoms of a broken timing belt on a dodge cummins diesel engine?


if the timing belt is broke - the motor will not crank - if it jumped time - it may run , but be low on power

Sep 25, 2009 | 1999 Dodge Ram 2500 4WD

1 Answer

Changed timing chain and need to align to cam with the crang


Align the chain with the colored links on the chain over the marks on the cams.Twin cams Have a small hole on the cam gears that will align with a hole in the front of head.Crank Gear has a pip mark that goes straight up.colored links on crank go to the 5 & 7 Oclock position on the lower crank gear with pip mark on crank gear at 12:00.Hope this helps

May 22, 2009 | 1995 Saturn Sl

1 Answer

91 chevy G20


well not sure exactly why it wont line up use something to turn the crank and cam to appropiate position start sliding crank gear until cam gear is touching then start to push both at same time make sure your crank key and cam pin are bothin place On many OHV pushrod engines, the crankshaft sprocket is installed on the crankshaft nose and the crankshaft is rotated to position piston #1 at TDC. At this point, a mark stamped onto the crankshaft sprocket is pointing directly upward (toward the camshaft).
The camshaft sprocket is then temporarily bolted to the cam and used to rotate the cam until a mark stamped on the cam sprocket is pointing directly downward (toward the crankshaft). The sprocket is then removed from the cam (without allowing the cam to rotate).
The timing chain is looped over the cam gear, the mark on the cam gear is positioned directly downward, and the chain is looped around the crankshaft sprocket. When the cam sprocket is attached to the cam, the timing marks on the crank and cam sprockets should be pointing toward one another.

Feb 10, 2009 | 1992 Chevrolet G20

1 Answer

NEED TIMING MARKS 2.0L DUAL CAM FORD CONTOUR


the cam marks are on the cams under the valvecover the crank has a mark o nthe timing cover that you need to line it up to

Jan 02, 2009 | 1996 Ford Contour

1 Answer

Timing Belt Markings


Mark are on the crank and cam timing gears. Cam gear mark at 12 o"clock crank gear mark lined up with TGC mark on block when installing timing belt.

Dec 16, 2008 | Hyundai Motor 2002 Elantra

1 Answer

TIMING MARKS??


normally on most cars there is a mark indented in the cam\cams and a matching mark on the block usally a small dot. and the same on the crank on some cranks it also has a degree mark for setting the advance timing at the crank...not always though

Jul 14, 2008 | 1998 Plymouth Breeze

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...